SOMFY SOLIRIS Uno User manual

1
SOLIRIS Uno
Supply:
Degree of protection:
Class:
Operating temperature:
Environmental conditions:
Relay contacts load:
33 mm 17 mm
EN60669
EN50081-1
EN50082-1
SOLIRISUnoisawindandsunautomaticcontrolsystemforanACmotor.
Thewindspeedandamountofsunshinearemeasuredbyacombinedsensor.
Arainsensorcanalsobeconnected.
Whenthesunshines,theawning/blindisactivatedautomatically,eitherfullyortoanindi-
viduallyprogrammedintermediateposition.
Adynamicretractiondelayavoidsfrequentactivationcommandscausedbyvarying light
conditions. Manualoperationisalsopossibleandthesunfunctioncanbeswitchedoff.
Ifthewindistoostrongtheawning/blindisautomaticallyretractedandmanualoperation
isblocked. Thewindfunctionisasafetyfunctionandisalwaysactivated.
220–240V ~ 50/60Hz
IP40
II
+5°Cto+40°C
dry living areas.
cos >0,8/3A/230V/50Hz
Settingup,testing,commissioningand troubleshooting for thisequipmentshould only be car-
riedoutbyatrainedelectrician. Beforestartingwork,disconnectthe power to all connecting
wires,andtakestepstopreventtheir accidental reconnection. Correctoperationis only guar-
anteedwhenprofessionally installed and powersupplyisadequate.
!
80 mm
80 mm
INSTALLATION guide
Ref.9007509
inteoSOLIRIS Uno
1
Characteristics:
2
Installation:
We reserve the right to make changes due to technical improvements.

SOLIRIS Uno
2
2 x
Connectthewires to the termi-
nalsofthe connecting bracket
inaccordancewith the terminal
layout(chapter2.2).
Pressthesafety cover onto the
backofthe bracket then fitthis
oneonthe recessed box.
Toremovethe safety cover,usea screw-
driverto press gently in the slot providedin-
sidethe terminal block.
PlugtheSOLIRIS Uno control
unitintothe bracket,together
withthecover frame.
Whensetting(chapter 3) and
programming(chapter4) is
completed,the cover platecan
beclippedonto the control unit.
Terminal layout2.2
NL N
Soliris Uno connecting
Bracket
Terminal layout
Main Phase (L )
Main Neutral (N )
Motor Neutral (N)
Motor Up (▲)
Motor Down (▼)
N is bridged
internally
Common (C)
Sun sensor ( )
Wind sensor ( )
Rain sensor ( )
C
Mounting2.1
Test: When operating powerhasbeenconnected,the direction of
themotorcan be tested usingthe and buttons.
Soliris sensor Rain sensor
Soliris Uno
4x0,75mm2
2x 0,75 mm2
3x 0,75 mm2
Supply
3x 1,5 mm2
Supply
3x 1,5 mm2
We reserve the right to make changes due to technical improvements.
SOLIRISUnois suitable for mountingina60mmØconcealed connection box orsuitablesurfacemountingcap(Somfyaccessories).
NL N
C
SUPPLY
230V 50Hz
Phase
Neutral
Earth
LT motor DOWN
PE
N
UP
Soliris sensor
Soliris uno
C
Rain sensor
brown
brown blue
blue yellow/green

3
SOLIRIS Uno
The sun control function can be turned on and off using the sliding switch:
SuncontrolON :
theSOLIRISUno reacts in accordancewiththewind,the sun and with
themanualUP/DOWN/STOP commands.
SuncontrolOFF :
theSOLIRISUno reacts in accordancewiththewindinformationandwith the
manualUP/DOWN/STOPcommands.
The potentiometers allow the threshold values for brightness and wind speed to be set.
The wind and sun controls can be checked as follows
-Setthe suncontrolslidingswitchto SuncontrolON : .
-Setthe wind potentiometer to5km/handtheSunpotentiometertoTestposition
➜TheyellowSun LED shines continuously:The sundetectionisworkingcorrectly.
➜TheredWind LEDisilluminatedwhentheanemometerstarts to rotate :The wind detectionisworkingcorrectly.
5
20
40
60
max
km/h kLux
20
35
50
maxTest
kLux
20
35
50
maxTest
5
20
40
60
max
km/h
Wind and sun controls
3.1
We reserve the right to make changes due to technical improvements.
3
Settings:
MODE
UP button
LED red/green
Wind adjustment
Sun adjustment
LED yellow
SUN on/off switch
MODE button
STOP/IP button
DOWN button
Allmanualor
automatic
commandsare
inhibitedaslong asthe
windspeedis higher
thantheadjusted
threshold.
Whenthewind
speedexceedsthe
thresholdseton
theSOLIRISUno,
theredLED lights
onand theawning
isretractedafter 2
seconds.
Whenthewind
speedfallsbe-
lowthethreshold
setting,thered
LEDbeginsto blink.
Amanualcontrol canbe
givenafter30 secondsand
anautomaticsun control
canbegiven after12minutes.
after 12 min. after 30 sec.
Wind control operation
WIND
Windspeedsetting range:5-80km/h
Factory setting:approx.20 km/h
SUN
Brightnesssettingrange:20-60kLux
Factory setting:approx.35 kLux
after 2 secs.
Whenthedaylight levelfallsbelow the thresholdsetting,theyellow
LEDblinksand theawningis automatically retractedaftera variable
timingbetween30 to15mins.
Thistimingdepends onthesun presence durationandit avoidsfre-
quentmovementsof theawningon cloudy days.
shortperiodof sun(<30’) ➜ 30mins.before retraction.
longperiodof sun(>90’) ➜ 15mins.before retraction.
Moreover,If the daylightfallsbelow 12kLux,the timingisdecreased
toapprox.5 minutestoretract theawningmore quicklyattwilight.
Whentheintensity
ofthedaylight ex-
ceedsthethreshold
setbythe SOLIRIS
Uno,theyellowLED
lightsonand aDOWNorder is sent
totheawning after2minutes.
Theawninggoesto theintermediatepositionIP (see
4.2)ortoits downendlimitposition if nointermediate
positionhasbeenmemorised.
IP after 30-15 mins. or 5 mins.
Sun control operation

Inthe“US”mode,each time Up or arepressedbriefly this constitutes alongmovecommand,and if they arehelddownforalongerperiod
oftimethis constitutes a movecommandwithoutanautomaticstop. Aslat tilting command canbeprogrammed(chapter4.3).
Programmingvenetianblind mode“US”:
Press forapprox.2 seconds. TheredandyellowLEDsflashalternately. Then press untilthegreen LED lights uptwicebriefly(briefly
once–pause – briefly once).
➜Venetianblindmode“US”isprogrammed.
MODE
SOLIRIS Uno
4
Anoptionalrain sensor with afloatingcontactcanbeconnectedto the SOLIRIS Uno. Incaseofrain,the blind/awning is retractedautomatically.
TheredLED is illuminated. In thissituationallmanualcommandsandsun control commands areinhibited.They areagainpossibleassoonas
therainstops.
4.1.1 Awning mode
TheSOLIRISUno offers a rangeofextraprogrammablefunctions,allowing a greaterlevelofcomfort. Theadditionalprogrammingcapability ofthe
SOLIRISUnodepends on the operatingmodeselected(chapter4.1).
Precondition for programming
Duringprogramming,no information(e.g.sun,wind,etc)mustcomein(LED unlit),setthesuncontrolslidingswitch to Sun controlOFF .
Itisbest to raise theblind/awningtoitshighestposition(retracted).
Oncetheblind/awning is in itsfinalposition(retracted),the relay must haveswitchedoff(eitherautomaticallyafter3 minutesorpress the button.
Mode of operation
4.1
Inawningmode,eachtime or is pressed thisconstitutesamovecommand.Thismode is set bydefaultinfactory.
Programmingawningmode:
Press forapprox.2 seconds. TheredandyellowLEDsflashalternately. Then press forapprox.2 secondsuntiltheyellowLEDlights up
brieflytwice(briefly once – pause–brieflyonce).
➜Awningmodeisprogrammed.
MODE
4.1.2 Venetian blind mode“EU”
4.1.3 Venetian blind mode“US”
Test: The programming oftheoperatingmodecanbetested. Press briefly
➜theLEDallocated to the setoperatingmodelightsupbriefly.
YellowLED :awningmode.
RedLED: Venetianblind“EU”mode.
GreenLED:Venetianblind“US”mode.
MODE
We reserve the right to make changes due to technical improvements.
4
Programming:
Inthe“EU”mode,each time or are pressedbriefly,thisconstitutesashortmove command,andiftheyarehelddownfor a longer periodof
time,this constitutes alongermovecommand. Aslattiltcommand can be programmed(chapter4.3).
Programmingvenetianblind mode“EU”:
Press forapprox.2 seconds. TheredandyellowLEDsflashalternately. Then press untilthered LED lights upbrieflytwice(brieflyonce –
pause–briefly once).
➜Venetianblindmode“EU”isprogrammed.
MODE
Rain control
3.2

5
SOLIRIS Uno
1.Move the awning/blindtoitsUPposition(awning/blindretracted).
2.Press and simultaneouslyforapprox.3 secondsuntiltheawning/blindbeginstomove down.
➜theLEDshines green.
3.Stop the awning/blindatthepositionyouwishto record as theintermediateposition(Correctingthepositionusing , and willnotaf-
fecttheprogramming process.)
4.Press for approx.2seconds.
➜ThegreenLED lights off,theintermediatepositionisprogrammed.
Iftheawning/blind is above theintermediateposition,press .
➜ Theawning/blindwill move to theintermediateposition.
Iftheawning is below theintermediateposition,nothinghappens.
IftheSun control sliding switchissettosuncontrolOn and the awning/blind isabovetheintermediateposition,the awning/blind willauto-
maticallymoveto the intermediate positionassoonasthebrightnessexceeds the value setontheSunpotentiometer.
Theawning/blindmust be in theintermediateposition. Tocancel the intermediate position,press for approx.10seconds.
➜TheLEDwill shine red,theintermediatepositionisnow cancelled.
Inawningand venetian blind modes(chapter4.1)itispossibleto program an intermediatepositionfromtheUPlimitposition (awning/blind re-
tracted).
Freely selectable intermediate position
4.2
Intermediate position
To programme theslattiltingoperationanintermediateposition must already have been
programmed(chapter4.2).
1.Set the venetianblindatitsUPlimit position(blind retracted).
2.Press .
➜ Theblindwill move to theintermediateposition,theslats are closed.
3.Press and simultaneously.
➜ Afterapprox.3 secondstheslatswillmomentarilymoveUP and the LEDshinesgreen.
4.Adjustthe right tiliting angleusing ,and .
5.Press for approx.2seconds.
➜ThegreenLED light off,theslattiltingprocedureis now programmed.
Slat tilting
4.3
InVenetianblindmode (chapter 4.1.2 and4.1.3)itispossibletoprogramme a slat tiltingoperation.
UPlimitposition DOWN limit positionIntermediate position
We reserve the right to make changes due to technical improvements.
4.2.1 Programmingtheintermediate position
4.2.2 Reachtheintermediate position
4.2.3 Canceltheintermediate position
4.3.1 Programmingtheslat tilting operation
Oncetheintermediate position has beenreached(chapter4.2.2),the blind automatically movesupwardswiththeprogrammedslat tilt.
Iftheblind is below theintermediatepositionandthelastorder was a DOWNcommand,youwillonly get the tiltingoftheslatsbypressing .
To cancel,theblindismoveddown from its highest finalposition(blindretracted)tothe intermediate position using the button. Whenit
reachestheintermediate position the slattiltingoperationautomaticallyopenstheslats. Tocanceltheslat tilting operation,press forapprox.
10seconds.
➜Assoonas the red LEDisilluminated,theslat tilt and intermediatepositionarecancelled.
4.3.2 Callingupthe slat tilting operation
4.3.3 Canceltheslat tilting operation

Fordemonstratingthe control functions itispossibletoshortenthe
reactiontimesof the SOLIRIS Uno.
To do this,the SOLIRISUnocanbeswitchedtodemo-mode.The
maximummovementtime from highest tolowestendpositionin
demo-modeisapprox.30seconds. Allothersettingsandprogram-
mingwillbe performed as previously.
SOLIRIS Uno
6
Demo setting
4.4
4.4.1 Demo setting – awnings
Intheawning demo setting,eachtime or arepressedthis constitutes one command.
Programmingtheawning demo setting
Press forapprox.2 seconds. TheredandyellowLEDsflashalternately. Then press and simultaneouslyuntilthe yellow
LEDlightsup 4 times (twicebriefly–pause–twicebriefly).
➜Awningdemosettingisprogrammed.
MODEMODE
4.4.2 Demo setting – venetian blind“EU”
Inthe“EU”blinddemosetting,each time or arepressed briefly this constitutesoneshortmovecommand,and if theyarehelddown
foralonger time this constitutesalongermovecommand. Aslattilting operation can beprogrammed(chapter4.3).
Programmingthe“EU”venetianblinddemosetting
PressModefor approx.2seconds. TheredandyellowLEDs flash alternately. Thenpress and simultaneously until the redLED
lightsup4 times (twice briefly–pause–twicebriefly).
➜“EU”venetian blind demoisprogrammed.
MODE
4.4.3 Demo setting – venetian blind“US”
Inthe“US”blinddemosetting,each time or arepressed briefly this constitutesonelongmovecommand,and if theyarehelddown
foralonger time this constitutesashortmovecommand. Aslattilting operation can beprogrammed(chapter4.3).
Programmingthe“US”venetianblinddemosetting
PressModefor approx.2seconds. TheredandyellowLEDs flash alternately. Thenpress and simultaneouslyuntilthegreenLED
lightsup4 times (twice briefly–pause–twicebriefly).
➜“US”venetian blind demoisprogrammed.
MODE
Test: The programming oftheoperatingmodecanbetested as follows. Press briefly
➜theLEDallocated to the setoperatingmodelightsuptwicebriefly.
YellowLED :awningdemosetting
RedLED:“EU”venetianblinddemosetting
GreenLED:“US”venetianblinddemosetting
Quittingdemomode
To quit thedemomode,programin the desired operatingmode,asdescribed in chapter 4.1
MODE
We reserve the right to make changes due to technical improvements.
Normal mode Demo mode
SUNappearing: 2 min. 10sec.
SUNdisappearing: 15/30 min. 15/30sec.
WINDappearing: 2 sec. 2sec.
WINDdisappearing: 30sec. 12min. 15sec.
Outputrelays: 180 sec. 30sec.
TIMINGS