SOMFY Animeo Series User manual

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 1/56
68
© 2019, SOMFY ACTIVITES SA . ALL RIGHTS RESERVED . REF. 5147817A –2019/01/31

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 2/56
Table of contents
1Definitions.......................................................................................................................................4
1.1 Manual Command............................................................................................................................4
1.2 Automatic Command........................................................................................................................4
1.3 US push button ergonomics.............................................................................................................4
1.4 EU push button ergonomics.............................................................................................................4
1.5 Screen push button ergonomics ......................................................................................................4
1.6 On/Off/Toggle...................................................................................................................................4
1.7 Position of the slats..........................................................................................................................5
2Installation ......................................................................................................................................6
3Wiring diagramm............................................................................................................................7
4Settings in the delivery state ........................................................................................................7
4.1 Function of the Reset/Prog button ...................................................................................................8
4.2 Selection of different user ergonomics.............................................................................................9
4.3 Changing the ergonomics ................................................................................................................9
4.4 Manual learning-in of move times..................................................................................................10
4.5 Manual learning-in of the intermediate position 1 ..........................................................................10
4.6 Resetting to the delivery state........................................................................................................11
5Communication objects...............................................................................................................12
5.1 Object overview..............................................................................................................................12
6Parameter......................................................................................................................................22
6.1 Menu index card “General”.............................................................................................................22
6.2 Menu index card “Configuration for motor 1...4” ............................................................................25
6.3 Menu index card “Functions for motor 1...4” ..................................................................................28
6.4 General information for Binary inputs.............................................................................................30
6.5 Menu index card “Binary inputs - Venetian blind Up/Down” ..........................................................31
6.6 Menu index card “Binary inputs – Switch/Dry contact” ..................................................................32
6.7 Menu index card “Binary inputs – 8-Bit value (rising edge)” ..........................................................34
6.8 Menu index card “Binary inputs – Dimming” ..................................................................................35
6.9 Menu index card “General Binary inputs”.......................................................................................38
6.10 Menu index card “Electronic motors” .............................................................................................39
6.11 Menu index card “Bus safety”.........................................................................................................40
6.12 Menu index card “Feedback motor position”..................................................................................42
6.13 Menu index card “General Radio inputs” .......................................................................................44
6.14 General information for radio input.................................................................................................44
6.15Menu index card “Radio inputs – Venetian blinds Up/Down”.........................................................45
6.16 Menu index card “Radio inputs – Switch”.......................................................................................46
6.17 Menu index card “Radio inputs – 8-Bit value” ................................................................................49
6.18 Menu index card “Radio inputs – Dimming”...................................................................................51
6.19 Menu index card “Radio inputs – Venetian blind slow tilting”.........................................................53
7Technical data ..............................................................................................................................55

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 3/56
Before starting up it is necessary to follow the safety instructions in these instructions.
SOMFY cannot be held liable for defects and damages when these have been caused as a re-
sult of not following instructions (wrong installation, incorrect service etc.). Establishing, testing
and starting up of the equipment is permitted only by a qualified person (in accordance with
VDE 0100). Switch on all connections without voltage. Take precautions against unintentional
turning on.
The installation of the Somfy products may occur only at easily accessible places. If maintenance and re-
pair become substantially hindered by accessibility (e.g. stuck or extensively stuck flooring, installation
behind lamps or behind façades), any originating supplementary costs therein cannot be charged to the
seller.
Subject to technical changes.
The animeo KNX 4 DC Motor Controller WM 24 V DC is suited for selecting up to four individually param-
eterable motors for Venetian blinds, roller shutters, awnings and windows. The local push button inputs
can be used as conventional push buttons or as universal KNX binary inputs.
Functions and advantages
•Time savings through easy installation, for example using spring connectors, strain relief cable bind-
ers, sufficient enough clamping space.
•A group input can be used to control all four motors independently of ETS programming.
•Testing the moving direction of the motors is possible without ETS.
•The device can be used in delivery state without programming with the ETS software.
•Four local push button inputs can be used as maximum to connect eight universal KNX binary inputs,
for example window contacts, temperature switches or presence detectors. By using conventional
push buttons, lighting can also be controlled and dimmed.
•User-friendly and intuitive parameter settings in the ETS software.
•Intelligent change-over between manual operation and automatic operation to guarantee excellent
user friendliness and energy savings.
•Position messaging of the motors during the movement and when reaching the upper or lower end
position.
•Two different safety positions, freely determinable for every individual motor output.
•Safety position with mains voltage return freely determinable and messaging over building.
•Automatic cascading of the outputs with mains voltage return and bus-safety functions to minimise
power peaks.
•Plug and Play! Any time extendable with animeo RTS Radio Module (ref. 1860105) or animeo
EnOcean Receiver (ref. 1860220). Without additional wiring the four motors can be controlled individu-
ally per radio using Somfy RTS technology.
•Alternatively the animeo KNX RTS Receiver (ref. 1860191) or animeo KNX EnOcean Receiver (ref.
1860229) can be used. Here, without additional wiring, up to 5 universal KNX radio binary inputs can
be gained (e.g. light ON/OFF with DIM).
A complete commissioning is possible if the KNX Motor Controller is connected to and powered
by the KNX bus.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 4/56
1 Definitions
1.1 Manual Command
A manual command is a command which is generated by local conventional push buttons or by a Somfy
RTS radio hand transmitter. A telegram which is sent on the objects 1-12 (bit commands) is also understood
as a manual command.
1.2 Automatic Command
A telegram which is sent on the objects 13-20 (byte commands) is understood as an automatic command.
1.3 US push button ergonomics
With this parameter it is ensured that the Venetian blind is controlled in the US ergonomics over the local
push button inputs or over the Somfy RTS radio hand transmitter.
Short pressing of the push button (< 0.5 s): A move command is carried out.
Long pressing of the push button (> 0.5 s): A turn command is carried out, as long as the push button is
pressed. When released, the turn command is stopped.
If the current position of the Venetian blind is beyond the turn, a move command is carried out with pressed
push button.
1.4 EU push button ergonomics
With this parameter it is ensured that the Venetian blind is controlled in the EU ergonomics over the local
push button inputs or over the Somfy RTS radio hand transmitter.
Short pressing of the push button (< 0.5 s): A turn step is carried out.
Long pressing of the push button (> 0.5 s): A turn command is carried out as long as the push button is
pressed.
If the current position of the Venetian blind is beyond the turn, a move command is carried out.
1.5 Screen push button ergonomics
With this parameter it is ensured that the end product is controlled in screen ergonomics over the local push
button inputs or over the Somfy RTS radio hand transmitter.
Short pressing of the push button when the end product is moving: A stop command is carried out.
Long pressing of the push button when the end product is not moving: A drive command is carried out.
1.6 On/Off/Toggle
1.6.1 On
If an “On” telegram is generated the value “1” is transmitted on the corresponding KNX group address.
1.6.2 Off
If an “Off” telegram is generated the value “0” is transmitted on the corresponding KNX group address.
1.6.3 Toggle
If a “Toggle” telegram is generated the value is firstly inverted and then transmitted to the corresponding
KNX group address.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 5/56
1.7 Position of the slats
1.7.1 90°/0° Venetian blind
Turning direction Turning direction
Angle: 45 °
Turn: 50 %
KNX value: 50%
Angle: 90 °
Turn: 0 %
KNX value: 100%
Max. closed 50% turned
Turning direction
Angle: 0 °
Turn: 100 %
KNX value: 0%
Max. turned
1.7.2 90°/-90° Venetian blind
Turning direction Turning direction
Angle: 0 °
Turn: 50 %
KNX value: 50%
Angle: 90 °
Turn: 0 %
KNX value: 100%
Max. closed 50% turned
Turning direction
Angle: -90 °
Turn: 100 %
KNX value: 0%
Max. turned

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 6/56
2 Installation
Choose the right place for installation: Level surface with sufficient space
Installation of the Motor Controller 4 DC WM
Complete wiring and connect power supply

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 7/56
3 Wiring diagramm
The “US”-LED blinks regularly when the mains (24 V) and the KNX bus voltage are
connected actively on the device. The device is ready for operation when the “US”
LED blinks.
Connecttion to …
Cable
Twisted pair
Max. length
Stripping
length
Motors
Min.: 2 x 0.6 mm/22 AWG
Max.: 2 x 2.5 mm2/13 AWG
-
6 mm/0.24‘‘
Switch
Min.: 3 x 0.6 mm/22 AWG
Max.: 3 x 2.5 mm2/13 AWG
Recommended
100 m/330 ft
6 mm/0.24’’
Group control
Min.: 3 x 0.6 mm/22 AWG
Max.: 3 x 1.5 mm2/15 AWG
Recommended
100 m/330 ft
6 mm/0.24’’
KNX-Bus
2 x 0.8 mm/20 AWG
Required, according
to KNX guidelines
6 mm/0.24’’
24 V DC
Min.: 2 x 1.5 mm2/15 AWG
Max.: 2 x 2.5 mm2/13 AWG
-
10 m/33 ft
6 mm/0.24’’

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 8/56
4 Settings in the delivery state
The Motor Controller KNX can be used in the delivery state also without prior programming by the ETS soft-
ware. Practical presets are implemented in the device. These settings apply to all four motor outputs.
•Move times UP/DOWN, CLOSED/OPEN = 5 minutes
•Connection of local conventional push buttons is possible
The local push button inputs are assigned directly to the motor outputs: Push button input 1 controls motor
output 1 (fig. 1). The motor outputs can be controlled through bridging the wire at the push button inputs
when required (fig. 2).
4.1 Function of the Reset/Prog button
HThe basic settings in the KNX Motor Controller can be made using this push button. These basic settings
are possible only in the delivery state, before the device with the ETS was programmed, or after the device
was unassigned by the ETS.
The basic settings are overwritten by the settings in the ETS.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 9/56
4.2 Selection of different user ergonomics
Using the Reset/Prog button the press button user ergonomics for the local push button inputs or Somfy RTS
radio hand transmitter can be determined. These settings are possible only in the delivery state, before the
device is programmed with ETS software or after the device is unassigned with the ETS.
As soon as the device with the ETS is programmed, no further settings of the user ergonomics can be made
via the Reset/Prog button. When the device is unassigned by the ETS, the adjusting of the user ergonomics
is possible again via the Reset/Prog button.
HThe selection of the user ergonomics must match with a corresponding end product.
= Learning-in of animeo RTS radio module
SCR = Screen ergonomics*
EU = Venetian blind, EU ergonomics*
US = Venetian blind, US ergonomics*
*see chapter 1 “Definitions”
4.3 Changing the ergonomics
To change to different ergonomics
press briefly the Reset/Prog button.
Repeat till such time as the desired
LED shines.
The delivery state is Venetian Blind
with EU ergonomics
Save and
exit the
setting mode

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 10/56
4.4 Manual learning-in of move times
The move and turn times per motor output can be set via local conventional push buttons. These settings are
possible only in the delivery state before the device has been programmed with the ETS. As soon as the de-
vice with the ETS is programmed, the move times and turn times can no longer be set via local conventional
push buttons. When the device is unassigned by the ETS, the adjusting of the move times and turn times via
local conventional push buttons can be done again.
HAlternatively to the conventional push buttons, the settings can also be done using the Somfy RTS Trans-
mitter and animeo RTS Radio Module (ref. 1860105). A setting using animeo KNX RTS Receiver (ref.
1860191) and Somfy RTS Transmitter resp. animeo EnOcean Receiver (ref. 1860220) or animeo KNX
EnOcean Receiver (ref. 1860229) und EnOcean Receiver is not possible!
4.5 Manual learning-in of the intermediate position 1
Intermediate position 1 can be learned-in individually per motor output via conventional local push buttons. At
the same time, it is possible to carry out the intermediate position 1 via settings in the ETS parameters. Prior
to this, the move and turn times must be learned-in!
HAlternatively to the conventional push buttons, the settings can also be done using the Somfy RTS Trans-
mitter and animeo RTS Radio Module (ref. 1860105). A setting using animeo KNX RTS Receiver (ref.
1860191) and Somfy RTS Transmitter resp. animeo EnOcean Receiver (ref. 1860220) or animeo KNX
EnOcean Receiver (ref. 1860229) and EnOcean Sender is possible through using the objects 64-67!
4.5.1 Save intermediate position 1 (IP1)

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 11/56
4.5.2 Call intermediate position 1 (IP1)
4.6 Resetting to the delivery state
When the device has not been programmed with the ETS software.
The setting made via the Reset/Prog push button can be set back to the delivery state by pressing the
Reset/Prog button for 10 seconds.
When the device has been programmed with the ETS software.
When the device has been programmed with the ETS software, a reset in the delivery state is no longer pos-
sible via the Rest/Prog button. Over the function “Unload”in the ETS, all settings of the device can be set
back in the delivery state. The Reset/Prog button is then freed again.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 12/56
5 Communication objects
5.1 Object overview
At the most, 177 communication objects are available for use, but not all at once. A maximum of 250 group
addresses can be connected.
5.1.1 List of Objects
No.
Object name
Type
DPT_ID
Description
1
Motor 1 Up/Down, Close/Open
1 bit
1.008
If a telegram with the value “0” is received on this
communication object, the appropriate blind goes
up or the window closes. If a telegram with the
value “1” is received, the appropriate blind goes
down or the window opens. At expiration of the
adjusted running time for the UP and DOWN
direction the relays of the outputs are deac-
tivated.
2
Motor 2 Up/Down, Close/Open
1 bit
1.008
3
Motor 3 Up/Down, Close/Open
1 bit
1.008
4
Motor 4 Up/Down, Close/Open
1 bit
1.008
9
Motor 1 Step/Stop
1 bit
1.008
With Venetian blinds: If the Venetian blind is
moving, the move is stopped with the receiving of
a telegram on one of these communication ob-
jects, no matter whether “0”or “1”is received. If
the Venetian blind is stationary, a turn is carried
out. In addition, the slats turn CLOSED with the
receiving of a telegram with the value “1”and UP
with the receiving of a telegram with the value
“0”. The duration of the turning step is defined in
the parameter settings.
With vertical awnings, roller shutters, awnings
and windows: When one of the end products is
moving, the move is stopped with the receiving of
a telegram on one of these communication ob-
jects, no matter whether “0”or “1”is received. If
one of these end products is not moving and a
telegram is received on one of these communica-
tion objects, then no operation is carried out.
10
Motor 2 Step/Stop
1 bit
1.008
11
Motor 3 Step/Stop
1 bit
1.008
12
Motor 4 Step/Stop
1 bit
1.008
13
Motor 1 Position Up/Down
1 Byte
5.001
If a telegram is received on one of these commu-
nication objects, the corresponding blind will
move to the position which is defined by the
received value “0”= upper/”100”= lower.
With Venetian blinds: When the position is
reached, the same slats angle is moved to at
which the Venetian blind was before.
14
Motor 2 Position Up/Down
1 Byte
5.001
15
Motor 3 Position Up/Down
1 Byte
5.001
16
Motor 4 Position Up/Down
1 Byte
5.001
17
Motor 1 Slat position
1 Byte
5.001
With Venetian blinds: If a telegram is received on
one of these communication objects, the corre-
sponding slats will move to the position which is
defined by the received value. If a Venetian blind
18
Motor 2 Slat position
1 Byte
5.001
19
Motor 3 Slat position
1 Byte
5.001

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 13/56
No.
Object name
Type
DPT_ID
Description
20
Motor 4 Slat position
1 Byte
5.001
is moving and receives a value on the corre-
sponding object, the position of the slats is
moved to only when the move has been com-
pleted. Depending on the parameter settings on
the card index “General”the position is defined
as follows:
”100”= slats max. closed/
”0”= slats max. turned
or
”0”= slats max. closed/
”100”= slats max. turned
value (0/100)
value (100/0)
25
Motor 1 Move to IP1
1 bit
1.008
If a telegram with the value “1”is received on one
of these communication objects, the correspond-
ing blind moves to the ETS parameterized per
local switch or to the radio transmitted, learned-in
intermediate position 1, if the learned-in position
is valid. With the receiving of a telegram with the
value “0”on one of these communication objects,
the corresponding blind moves to the upper end
position.
26
Motor 2 Move to IP1
1 bit
1.008
27
Motor 3 Move to IP1
1 bit
1.008
28
Motor 4 Move to IP1
1 bit
1.008
29
Motor 1-4 Move to IP1
1 bit
1.008
If a telegram with the value “1”is received on this
communication object, the blinds 1-4 move to the
ETS parameterized per local switch or to the
radio transmitted, learned-in intermediate position
1, if the learned-in position is valid. With the re-
ceiving of a telegram with the value “0”on this
communication object, the blinds 1-4 move to the
upper end position.
30
Motor 1 Move to IP2
1 bit
1.008
If a telegram with the value “1”is received on one
of these communication objects, the correspond-
ing blind moves to the intermediate position 2 pa-
rameterized in the ETS parameters. With the re-
ceiving of a telegram with the value “0”on one of
these communication objects, the corresponding
blind moves to the upper end position.
31
Motor 2 Move to IP2
1 bit
1.008
32
Motor 3 Move to IP2
1 bit
1.008
33
Motor 4 Move to IP2
1 bit
1.008
34
Motor 1-4 Move to IP2
1 bit
1.008
If a telegram with the value “1”is received on this
communication object, the blinds move to the
Intermediate Position (IP) 2 parameterized in the
ETS parameters. With the receiving of a telegram
with the value “0”on this communication object
the blinds 1-4 move to the upper end position.
40
Motor 1 Security, low prio
1 bit
1.001
If a telegram with the value “1”is received on one
of these communication objects, the correspond-
ing blind moves to the position parameterized in
the ETS parameters (Security, low prio) and any
41
Motor 2 Security, low prio
1 bit
1.001
42
Motor 3 Security, low prio
1 bit
1.001

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 14/56
No.
Object name
Type
DPT_ID
Description
43
Motor 4 Security, low prio
1 bit
1.001
further move commands will be blocked. With the
receiving of a telegram with the value “0”on one
of these communication objects, the security is
turned off and move commands will be accepted
again. If “Repeat last telegram after security
(Yes)”has been selected in the ETS parameters,
the blind moves to the position it was, before
security was activated.
If on one of the communication objects 45-48
(Security, high prio) a telegram is received with
the value “1”, the corresponding blind moves to
the position parameterized in the ETS (Security,
high prio).
44
Motor 1-4 Security, low prio
1 bit
1.001
If a telegram with the value “1”is received on this
communication object, the blinds 1-4 move to the
position parameterized in the ETS parameters
(Security, low prio) and any further move com-
mands will be blocked. With the receiving of a tel-
egram with the value “0”on this communication
objects, the security is turned off and move com-
mands will be accepted again. If “Repeat last tel-
egram after security (Yes)”has been selected in
the ETS parameters, the blinds move to the posi-
tion they have been before security was acti-
vated.
If on the communication object 49 (Security, high
prio) a telegram is received with the value “1”, the
blinds 1-4 move to the position parameterized in
the ETS (Security, high prio).
45
Motor 1 Security, high prio
1 bit
1.001
If a telegram with the value “1”is received on one
of these communication objects, the correspond-
ing blind moves to the position parameterized in
the ETS parameters (Security, high prio) and any
further move commands will be blocked. With the
receiving of a telegram with the value “0”on one
of these communication objects, the security is
turned off and move commands will be accepted
again, if the corresponding object 40-43 (Secu-
rity, low prio) has the value “0”. Otherwise the
parameterized action for low security will be
carried out. When “Repeat last telegram after
security (Yes)”has been selected in the ETS
parameters and both securities for the corre-
sponding channel have the value “0”, the blind
moves to the position it was, before any security
was activated.
46
Motor 2 Security, high prio
1 bit
1.001
47
Motor 3 Security, high prio
1 bit
1.001
48
Motor 4 Security, high prio
1 bit
1.001

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 15/56
No.
Object name
Type
DPT_ID
Description
49
Motor 1-4 Security, high prio
1 bit
1.001
If a telegram with the value “1”is received on this
communication object, the blinds 1-4 move to the
position parameterized in the ETS parameters
(Security, high prio) and any further move com-
mands will be blocked. With the receiving of a tel-
egram with the value “0”on this communication
object, the security is turned off and move com-
mands will be accepted again, if the object 44
(Security, low prio) has the value “0”. Otherwise
the parameterized action for low security will be
carried out. If “Repeat last telegram after security
(Yes)”has been selected in the ETS parameters
and both securities have the value “0”, the blinds
move to the position they were, before any secu-
rity was activated.
50
Motor 1-4 Status positions
1 bit
1.001
If a telegram with the value “1”or “0”is received
on this communication object, the current status
positions of the corresponding blinds are sent to
the bus (objects 73-80).
51
Motor 1 Block functions
1 bit
1.001
If a telegram with the value “1”is received on one
of these communication objects, the functions
parameterized in the ETS for the corresponding
blind is blocked. If a telegram with the value “0”is
received on one of these communication objects,
the functions parameterized in the ETS for the
corresponding blind is no longer blocked and
freed again.
52
Motor 2 Block functions
1 bit
1.001
53
Motor 3 Block functions
1 bit
1.001
54
Motor 4 Block functions
1 bit
1.001
55
Motor 1-4 Block functions
1 bit
1.001
If a telegram with the value “1”is received on this
communication object, the functions parameter-
ized in the ETS for the blinds 1-4 are blocked. If a
telegram with the value “0”is received on this
communication object, the functions parameter-
ized in the ETS for the blinds 1-4 are no longer
blocked and freed again.
56
Motor 1 Prio automatic/manual
1 bit
1.003
Over these communication objects the priority
automatic function and priority manual function
can be switched. If a telegram with the value “1”
is received on one of these communication ob-
jects, the automatic functions for the correspond-
ing blind is prioritized activated. If a telegram with
the value “0”is received on one of these commu-
nication objects, the manual functions for the cor-
responding blind is active.
57
Motor 2 Prio automatic/manual
1 bit
1.003
58
Motor 3 Prio automatic/manual
1 bit
1.003
59
Motor 4 Prio automatic/manual
1 bit
1.003
60
Motor 1 Reset priority
1 bit
1.001
If a telegram with the value “1”or “0”is received
on one of these communication objects the prior-
ity switching for the corresponding blind is reset.
Automatic functions or manual functions are then
switched to priority active again. Whichever prior-
ity is active depends on the status of the commu-
nication objects 62-65 or whichever priority has
been parameterized in the ETS.
61
Motor 2 Reset priority
1 bit
1.001
62
Motor 3 Reset priority
1 bit
1.001
63
Motor 4 Reset priority
1 bit
1.001
64
Motor 1 IP1 Save/Delete
1 bit
1.002
If a telegram with the value “1”is received on one
of these communication objects the actual posi-
tion for the corresponding blind is learned as IP1.
If a telegram with the value “0”is received on one
of these communication objects the IP1 is deleted.
65
Motor 2 IP1 Save/Delete
1 bit
1.002
66
Motor 3 IP1 Save/Delete
1 bit
1.002

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 16/56
No.
Object name
Type
DPT_ID
Description
67
Motor 4 IP1 Save/Delete
1 bit
1.002
68
Main power failure (24 V)
1 bit
1.002
A mains power failure is signaled with this com-
munication object. 20 seconds after the mains
voltage cut out a telegram with the value “1”is
sent to the bus. With return of mains voltage this
communication object sends the telegram with
the value “0”.
73
Motor 1 Feedback UP/DOWN
1 Byte
5.001
Through these communication objects, the actual
position, based on the learned-in move time
(UP/DOWN direction) of the corresponding blind,
is sent to the bus. This kind of sending (on de-
mand, status change, cyclic) is set in the ETS
parameters.
“0“= upper/“100“= lower.
74
Motor 2 Feedback UP/DOWN
1 Byte
5.001
75
Motor 3 Feedback UP/DOWN
1 Byte
5.001
76
Motor 4 Feedback UP/DOWN
1 Byte
5.001
77
Motor 1 Feedback slat
1 Byte
5.001
Through this communication objects, the actual
slats position, based on the learned-in turn time,
is sent to the bus. This kind of sending (on de-
mand, status change, cyclic) is set in the ETS
parameters. The position, dependent of parame-
ter settings on the menu list “General”, is defined
as follows:
”100”= slats max. closed/”0”= slats max. turned
(standard)
or
”0”= slats max. closed/”100”= slats max. turned
78
Motor 2 Feedback slat
1 Byte
5.001
79
Motor 3 Feedback slat
1 Byte
5.001
80
Motor 4 Feedback slat
1 Byte
5.001
81
Motor 1 Upper end position
1 bit
1.002
Through these communication objects a telegram
with the value “1”for the corresponding blind is
sent when the upper end position is reached.
When leaving the upper end position of the corre-
sponding blind, a telegram with the value “0”is
sent. The upper and lower end position is deter-
mined by the parameterized move times.
82
Motor 2 Upper end position
1 bit
1.002
83
Motor 3 Upper end position
1 bit
1.002
84
Motor 4 Upper end position
1 bit
1.002
85
Motor 1-4 Upper end position
1 bit
1.002
Through this communication object a telegram
with the value “1”for the blinds 1-4 is sent when
all four blinds have reached the upper end posi-
tion. When all 4 blinds leave the upper end posi-
tion, a telegram with the value “0”is sent. The
upper and lower end position is determined by
the parameterized move times.
91
Motor 1 Lower end position
1 bit
1.002
Through this communication objects a telegram
with the value “1”for the corresponding blind is
sent when all four blinds have reached the lower
end position. When leaving the lower end posi-
tion of the corresponding motor, a telegram with
the value “0”is sent. The upper and lower end
position is determined by the parameterized
move times.
92
Motor 2 Lower end position
1 bit
1.002
93
Motor 3 Lower end position
1 bit
1.002
94
Motor 4 Lower end position
1 bit
1.002
95
Motor 1-4 Lower end position
1 bit
1.002
Through this communication object a telegram
with the value “1”is sent for the blinds 1-4 when
all four blinds have reached the lower end posi-
tion. When the corresponding blinds leave the
lower end position, a telegram with the value “0”
is sent. The upper and lower end position is de-
termined by the parameterized move times.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 17/56
No.
Object name
Type
DPT_ID
Description
96
Switch input 1: UP/DOWN
1 bit
1.008
A long pressing of the button on input A gener-
ates a telegram on this communication object
with the value “0”. The Venetian blind moves UP.
A long pressing of the button on input B gener-
ates a telegram on this communication object
with the value “1”. The Venetian blind moves
DOWN.
97
Switch input 1: STEP/STOP
1 bit
1.008
A short pressing of the button on input A gener-
ates a telegram on this communication object
with the value “0”. The slat turns UP. When the
Venetian blinds are making a move then a short
pressing of the button generates a stop com-
mand on input A. A short pressing of the switch
on input B generates a telegram with the value
“1”. The slats turn CLOSE. When the Venetian
blind is making a move then a short pressing of
the button generates a stop command on input B.
98
Input 1: A, Switch
1 bit
1.001
According to the parameter settings and the state
at input 1 contact A a switching telegram is sent
over this communication object with the value “1”
or “0”.
99
Input 1: B, Switch
1 bit
1.001
According to the parameter settings and the state
at input 1 contact B, a switching telegram is sent
over this communication object with the value “1”
or “0”.
100
Switch input 1: A, 8-Bit value
1 Byte
5.010
According to the parameter settings, with a rising
edge on input 1 contact A, the parameterized
value (0-255) is sent.
101
Switch input 1: B, 8-Bit value
1 Byte
5.010
According to the parameter settings, with a rising
edge on input 1 contact B, the parameterized
value (0-255) is sent.
102
Switch input 1: A/B, Dimming
1 Bit
1.001
On/Off:
According to the parameter settings, with a short
pressing at the input 1 contact A/B, a telegram is
generated with the value “1”or “0”.
Toggle/Toggle:
According to the parameter settings, with a short
pressing at the input 1 contact A/B, a telegram is
generated with the value “1”or “0”.
103
Switch input 1:
A/B, Dimming, Value
4 Bit
3.007
Brighter/darker dimming:
According to the parameter settings, brighter dim-
ming is done with a long pressing at the input 1
contact A. According to the parameter settings,
darker dimming is done with a long pressing at
the input 1 contact B.
Brighter/Darker toggle:
According to the parameter settings, over input 1
contact A, 100 % is dimmed with longer pressing
of the switch. When releasing the corresponding
switch at the input A, a stop command is gener-
ated. The last activated dimming step becomes
inverted. According to the parameter settings,
over input 1 contact A, 100 % is dimmed with
longer pressing of the switch. When releasing the
corresponding switch at the input B, a stop com-
mand is generated. The last activated dimming
step becomes inverted.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 18/56
No.
Object name
Type
DPT_ID
Description
104
Switch Input 2: UP/DOWN
1 Bit
1.008
see description of object 96, C/D instead of A/B
105
Switch Input 2: STEP/STOP
1 Bit
1.008
see description of object 97, C/D instead of A/B
106
Switch Input 2: C, Switch
1 Bit
1.001
see description of object 98, C instead of A
107
Switch Input 2: D, Switch
1 Bit
1.001
see description of object 99, D instead of B
108
Switch Input 2: C, 8-Bit value
1 Bit
5.010
see description of object 100, C instead of A
109
Switch Input 2: D, 8-Bit value
1 Bit
5.010
see description of object 101, D instead of B
110
Switch Input 2: C/D, Dimming
1 Bit
1.001
see description of object 102, C/D instead of A/B
111
Switch Input 2: C/D, Dimming,
value
4 Bit
3.007
see description of object 103, C/D instead of A/B
112
Switch Input 3: UP/DOWN
1 Bit
1.008
see description of object 96, E/F instead of A/B
113
Switch Input 3: STEP/STOP
1 Bit
1.008
see description of object 97, E/F instead of A/B
114
Switch Input 3: E, Switch
1 Bit
1.001
see description of object 98, E instead of A
115
Switch Input 3: F, Switch
1 Bit
1.001
see description of object 99, F instead of B
116
Switch Input 3: E, 8-Bit value
1 Bit
5.010
see description of object 100, E instead of A
117
Switch Input 3: F, 8-Bit value
1 Bit
5.010
see description of object 101, F instead of B
118
Switch Input 3: E/F, Dimming
1 Bit
1.001
see description of object 102, E/F instead of A/B
119
Switch Input 3: E/F, Dimming, value
4 Bit
3.007
see description of object 103, E/F instead of A/B
120
Switch Input 4: UP/DOWN
1 Bit
1.008
see description of object 96, G/H instead of A/B
121
Switch Input 4: STEP/STOP
1 Bit
1.008
see description of object 97, G/H instead of A/B
122
Switch Input 4: G, Switch
1 Bit
1.001
see description of object 98, G instead of A
123
Switch Input 4: H, Switch
1 Bit
1.001
see description of object 99, H instead of B
124
Switch Input 4: G, 8-Bit value
1 Bit
5.010
see description of object 100, G instead of A
125
Switch Input 4: H, 8-Bit value
1 Bit
5.010
see description of object 101, H instead of B
126
Switch Input 4: G/H, Dimming
1 Bit
1.001
see description of object 102, G/H instead of A/B
127
Switch Input 4: G/H, Dimming,
value
4 Bit
3.007
see description of object 103, G/H instead of A/B
128
Radio Input 1: UP/DOWN
1 Bit
1.008
A long pressing of “UP”button at channel 1
learned in remote generates a telegram with the
value “0” on this communication object. The
Venetian blind goes UP.
A long pressing of “DOWN”button at channel 1
learned in remote generates a telegram with the
value “1” on this communication object. The
Venetian blind goes DOWN.
129
Radio Input 1: STEP/STOP
1 Bit
1.008
A short pressing of “UP”button at channel 1
learned in remote generates a telegram with the
value “0” on this communication object. The slat
will tilt to reverse (open). If the Venetian blind is
in the fully moving process with a short pressing
of “UP”button at channel 1 learned in remote, a
stop order is generated.
A short pressing of “DOWN”button at channel 1
learned in remote generates a telegram with the
value “1” on this communication object. The slat
will tilt to close. If the Venetian blind is in a fully
moving process with a short pressing of “DOWN”
button at channel 1 learned in remote a stop
order is generated.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 19/56
No.
Object name
Type
DPT_ID
Description
130
Radio Input 1: Switch “my”button
1 Bit
1.001
According to the parameter settings a pressing of
“my”button at channel 1 learned in remote gen-
erates a telegram with the value “1” or “0”on this
communication object.
131
Radio Input 1: 8-Bit value “my”but-
ton
1 Byte
5.010
According to the parameter settings a pressing of
“my”button at channel 1 learned in remote the
configured value (0-255) is sent.
132
Radio Input 1: Switch “UP”button
1 Bit
1.001
According to the parameter settings a pressing of
“UP”button at channel 1 learned in remote gen-
erates a telegram with the value “1” or “0”on this
communication object.
133
Radio Input 1: Switch “DOWN”but-
ton
1 Bit
1.001
According to the parameter settings a pressing of
“DOWN”button at channel 1 learned in remote
generates a telegram with the value “1” or “0”on
this communication object.
134
Radio Input 1: 8-Bit value “UP”but-
ton
1 Byte
5.010
According to the parameter settings a pressing of
“UP”button at channel 1 learned in remote the
configured value (0-255) is sent.
135
Radio Input 1: 8-Bit value “DOWN”
button
1 Byte
5.010
According to the parameter settings a pressing of
“DOWN”button at channel 1 learned in remote
the configured value (0-255) is sent.
136
Radio Input 1: Dimming ON/OFF or
Slow Tilting UP/DOWN
1 Bit
1.001
On/Up:
According to the parameter settings a short
pressing of “UP”button at channel 1 learned in
remote a telegram with the value “0“ will be gen-
erated.The light will be switched ON or the blinds
will move UP
Off/Down:
According to the parameter settings a short
pressing of “DOWN”button at channel 1 learned
in remote a telegram with the value “1“ will be
generated.The light will be switched OFF or the
blinds will move DOWN
Toggle/Toggle:
According to the parameter settings a short
pressing of “UP”or “DOWN”button at channel 1
learned in remote a telegram with the value “1“
and/or “0“ is generated. The light will be switched
ON respectively OFF or the blinds will move UP
respectively DOWN.
137
Radio Input 1: Dimming Brighter/
Darker
or Slow Tilting Open/Close
4 Bit
3.007
3.008
Brighter/darker dimming:
According to the parameter settings of the input 1
contact A with a long actuation it is dimmed
brighter. According to the parameter settings of
the input 1 contact B with a long actuation it is
dimmed darker.
Brighter/darker toggle:
According to the parameter settings of the input 1
contact A with a long actuation it is dimmed
100 %. When releasing the appropriate switch at
the input A a stop order is generated. The dim-
ming action operated last is thus inverted.
According to the parameter settings of the input 1
contact B with a long actuation it is dimmed
100 %. When releasing the appropriate switch at
the input B a stop order is generated. The dim-
ming action operated last is thus inverted.

animeo KNX 4 DC Motor Controller 28.02.2019
WM 24 V DC
2019 Somfy Activités SA Ref. 5147817A 20/56
No.
Object name
Type
DPT_ID
Description
138
Radio Input 2: UP/DOWN
1 Bit
1.008
see description of object 128, channel 2 instead
of channel 1
139
Radio Input 2: STEP/STOP
1 Bit
1.008
see description of object 129, channel 2 instead
of channel 1
140
Radio Input 2: Switch “my”button
1 Bit
1.001
see description of object 130, channel 2 instead
of channel 1
141
Radio Input 2: 8-Bit value “my”but-
ton
1 Byte
5.010
see description of object 131, channel 2 instead
of channel 1
142
Radio Input 2: Switch “UP”button
1 Bit
1.001
see description of object 132, channel 2 instead
of channel 1
143
Radio Input 2: Switch “DOWN”but-
ton
1 Bit
1.001
see description of object 133, channel 2 instead
of channel 1
144
Radio Input 2: 8-Bit value “UP”but-
ton
1 Byte
5.010
see description of object 134, channel 2 instead
of channel 1
145
Radio Input 2: 8-Bit value “DOWN”
button
1 Byte
5.010
see description of object 135, channel 2 instead
of channel 1
146
Radio Input 2: Dimming
1 Bit
1.001
see description of object 136, channel 2 instead
of channel 1
147
Radio Input 2: Dimming/slow tilting
4 Bit
3.007
3.008
see description of object 137, channel 2 instead
of channel 1
148
Radio Input 3: UP/DOWN
1 Bit
1.008
see description of object 128, channel 3 instead
of channel 1
149
Radio Input 3: STEP/STOP
1 Bit
1.008
see description of object 129, channel 3 instead
of channel 1
150
Radio Input 3: Switch “my”button
1 Bit
1.001
see description of object 130, channel 3 instead
of channel 1
151
Radio Input 3: 8-Bit value “my”but-
ton
1 Byte
5.010
see description of object 131, channel 3 instead
of channel 1
152
Radio Input 3: Switch “UP”button
1 Bit
1.001
see description of object 132, channel 3 instead
of channel 1
153
Radio Input 3: Switch “DOWN”but-
ton
1 Bit
1.001
see description of object 133, channel 3 instead
of channel 1
154
Radio Input 3: 8-Bit value “UP”but-
ton
1 Byte
5.010
see description of object 134, channel 3 instead
of channel 1
155
Radio Input 3: 8-Bit value “DOWN”
button
1 Byte
5.010
see description of object 135, channel 3 instead
of channel 1
156
Radio Input 3: Dimming
1 Bit
1.001
see description of object 136, channel 3 instead
of channel 1
157
Radio Input 3: Dimming/slow tilting
4 Bit
3.007
3.008
see description of object 137, channel 3 instead
of channel 1
158
Radio Input 4: UP/DOWN
1 Bit
1.008
see description of object 128, channel 4 instead
of channel 1
159
Radio Input 4: STEP/STOP
1 Bit
1.008
see description of object 129, channel 4 instead
of channel 1
160
Radio Input 4: Switch “my”button
1 Bit
1.001
see description of object 130, channel 4 instead
of channel 1
161
Radio Input 4: 8-Bit value “my”but-
ton
1 Byte
5.010
see description of object 131, channel 4 instead
of channel 1
162
Radio Input 4: Switch “UP”button
1 Bit
1.001
see description of object 132, channel 4 instead
of channel 1
163
Radio Input 4: Switch “DOWN”but-
ton
1 Bit
1.001
see description of object 133, channel 4 instead
of channel 1
164
Radio Input 4: 8-Bit value “UP”but-
ton
1 Byte
5.010
see description of object 134, channel 4 instead
of channel 1
165
Radio Input 4: 8-Bit value “DOWN”
button
1 Byte
5.010
see description of object 135, channel 4 instead
of channel 1