SOMFY J4 io Assembly instructions

J4 io
Ref. 5068780A
Notice installateur
Installationsanleitung
Guida d’installazione
Installer Guide
EN DE FR
IT

56 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
CONTENTS
1. Introduction 56
2. Safety 57
2.1. Safety and responsibility 57
2.2. Specic safety advice 57
3. Installation 58
3.1. 58 x 51 mm or 58 x 56 mm head rail,
open below 58
3.2. 58 x 56 mm head rail, open above 58
3.3. 57 x 51 mm head rail, open above 59
3.4. 78 X 67 mm head rail, open below 60
3.5. 67 X 66 mm head rail, open below 62
3.6. J4 io Plate 62
4. Wiring 63
5. Commissioning 64
5.1. Identifying setting steps already
completed 64
5.2. Pre-programming the Somfy io local
control point 64
5.3. Checking the motor's direction of rotation65
5.4. Basic settings (end limits and
angular travel) 65
5.5. Programming the rst Somfy io local
control point 66
5.6. Checking the settings 66
6. Operation 67
6.1. Standard operation 67
6.2. Operating with a Somfy sensor or
automatic function 67
7. Modifying the settings 67
7.1. Favourite position (my) 67
7.2. Adding/Deleting Somfy io control points
and io sensors 68
7.3. Modifying the end limits 68
7.4. Modifying the angular travel 69
8. Tips and recommendations 70
8.1. Questions on the J4 io? 70
8.2. Replacing a lost or broken Somfy io
control point 71
8.3. Replacing a component of the actuator71
8.4. Restoring the original conguration 71
9. Technical data 72
1. INTRODUCTION
The J4 io actuator is designed to drive the external venetian blind, types 1 & 2.
What is io-homecontrol®?
The J4 io uses io-homecontrol®, the new universal and secure wireless communica-
tion protocol, shared by the major manufacturers in the world of home automation.
io-homecontrol® enables all comfort and security equipment to intercommunicate and be
actuated via a single control point.
The exibility and perfect compatibility of the io-homecontrol® system provides support for
you as your needs evolve. You can start by automating roller shutters, external venetian
blinds and the front door, then equip the outside awnings, the gate and garage door or
garden lighting with the io-homecontrol® system.
These scalable items of equipment are still compatible with the existing system, thanks to
io-homecontrol® technology, which ensures their interoperability.
For further information please visit the website www.io-homecontrol.com..
io-homecontrol® provides advanced and secure radio technology that is easy to install.
io-homecontrol® labelled products communicate with each other, improving comfort,
security and energy savings.
www.io-homecontrol.com

57
© 2011 Somfy SAS. All rights reserved. 112011
EN
2. SAFETY
2.1. Safety and responsibility
- The motor, torque and operating time must be adjusted according to the complete installation.
- Only Somfy original accessories should be used (adapters, brackets, connectors, power cable, etc.).
- Fitting, testing, commissioning and repair of the installation must only be carried out by qualied personnel.
- Correct operation of the installation is only guaranteed if the installation and assembly have been carried out
according to best practices, if the electrical supply is adequate and if maintenance is carried out.
- The installer must also comply with the current standards and legislation in the country in which the product
is being installed, and inform his customers of the usage and maintenance conditions relevant to the product.
- The moving parts of the motors must be protected if operating at less than 2.50 m from the ground or another
surface.
- The installation must not be used if it shows any signs of damage (for example wear, damaged cables and
springs or ill adjusted end limits).
- The installation must be protected from all unauthorised use. Take preventive measures to avoid any spurious
operation.
- Children must be supervised to ensure they do not play with the equipment. Keep remote controls out of the
reach of children.
- This equipment is not intended for use by persons (including children) with impaired physical or mental capaci-
ties or those without the required knowledge or experience unless supervised by a person responsible for their
safety.
- Disconnect all the connection cables from the power supply before operating on the installation.
- Do not use the installation if operations (window cleaning for example) are being carried out nearby.
- Observe the assembly and use guidelines, in particular the safety instructions from the manufacturer of the
device to be used.
Subject to technical modications.
2.2. Specic safety advice
In addition to the safety instructions described in this guide, be sure to also observe the
instructions set out in the attached document "Safety instructions to follow and keep".
1) Switch off the mains supply for the external venetian
blind before performing any service operation in the
vicinity.
To avoid damaging the product:
2) Never immerse it in liquid!
3) Avoid impacts!
4) Do not drop it!
5) Never drill holes in it!
6) Avoid moving the blind if ice has formed on it.
1
3
5 6
2
4
OFF

58 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
3. INSTALLATION
• Screw the 2 adaptors (1) using 2 M3x8 bolts (2) on
the motor shaft.
Tightening torque = 1.1 Nm
Ensure that the J4 io plate cable does not pass
over a rotating part of the motor or mechanism.
• If necessary, compress the edge of the head rail (4)
into the motor zone.
• Insert the motor into the head rail (4).
• Using the clips (5), attach the motor in the head rail
(4) above the acoustic tapes (6a).
• The shaft can be fitted into the adapter using a head-
less screw (7).
Installation with external clips
• Screw the 2 adaptors (1) using 2 M3x8 bolts (2) on
the motor shaft.
Tightening torque = 1.1 Nm
Ensure that the J4 io plate cable does not pass
over a rotating part of the motor or mechanism.
• Insert the motor into the head rail (4).
• Using the clips (5), attach the motor in the head rail
(4) above the acoustic tapes (6a).
• The shaft can be fitted into the adapter using a
headless screw (7).
5
4
7
7
4
3.1 57 X 51 mm or 58 x 56 mm head rail, open below
3.2 58 x 56 mm head rail, open above
2
7
1
1
7
2
6a
2
7
1
1
7
2
7
54
7
6a
5
5

59
© 2011 Somfy SAS. All rights reserved. 112011
EN
Installation with external clips
• Screw the 2 adaptors (1) using 2 M3x8 bolts (2) on
the motor shaft.
Tightening torque = 1.1 Nm
Ensure that the J4 io plate cable does not pass
over a rotating part of the motor or mechanism.
• Insert the motor into the head rail (4).
• Using the clips (5), attach the motor in the head rail
(4) above the acoustic tapes (6a).
• The shaft can be fitted into the adapter using a head-
less screw (7)
Installation with internal clips
• Screw the 2 adaptors (1) using 2 M3x8 bolts (2) on
the motor shaft.
Tightening torque = 1.1 Nm
Ensure that the J4 io plate cable does not pass
over a rotating part of the motor or mechanism.
• Insert the motor into the head rail (4).
• Using the clips (5), attach the motor in the head rail (4).
• The shaft can be fitted into the adapter using a head-
less screw (7).
The internal clips cannot be used with J418
motors (J4 motors with a torque of 18 Nm).
3.3 57 x 51 mm head rail, open above
1
2
12
4
5
7
7
7
7
5
2
7
1
1
7
2
7
54
7
6a
5

60 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
Installation with J406/J410 motors
(torque of 6 or 10 Nm)
• Screw the 2 adaptors (1) using 2 M3 x 8 bolts (2) on
the motor shaft.
Tightening torque = 1.1 Nm
Ensure that the J4 io plate cable does not pass
over a rotating part of the motor or mechanism.
• Fit the two head rail adaptors (8) on the motor.
• Insert the motor into the head rail (4).
• Using the clip (5), attach the motor in the head rail (4).
• The shaft can be fitted into the adapter using a head-
less screw (7).
3.4 78 x 67 mm head rail, open below
1
21
2
8
5
8
5
5
7
7
7
7
4

61
© 2011 Somfy SAS. All rights reserved. 112011
EN
Assembly with J418 motor (torque = 18 N.m)
• Screw the 2 adaptors (1) using 2 M3 x 8 bolts (2) on
the motor shaft.
Tightening torque = 1.1 Nm
Ensure that the J4 io plate cable does not pass
over a rotating part of the motor or mechanism.
• Fit the two head rail adaptors (8) on the motor.
• Insert the motor into the head rail (4).
• Using the clip (5), attach the motor in the head rail (4).
• The shaft can be fitted into the adapter using a head-
less screw (7).
• Fit the additional calliper (9) to the head rail (4) +
motor assembly.
• Screw the calliper (9) to the motor with an M5 x 10 mm
bolt. Tightening torque = 4 N.m maximum.
The bolt must be compressed against the calliper (9).
1
21
2
8
5
8
5
5
7
7
7
7
4
9

62 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
• Screw the 2 adaptors (1) using 2 M3 x 8 bolts (2) on
the motor shaft.
Tightening torque = 1.1 Nm
Ensure that the J4 io plate cable does not pass
over a rotating part of the motor or mechanism.
• Fit the two head rail adaptors (8) on the motor.
• Insert the motor into the head rail (4).
• Using the clips (5), attach the motor in the head rail (4).
3.5 67 x 66 mm head rail, open below
1
2
1
2
8
5
5
8
77
77
4
3.6 J4 io Plate
The J4 io plate is supplied connected to the motor; it must be integrated into or on the outside
of the head rail. If Somfy sensor is being used, the plate must be xed to the outside of the
head rail.
191 mm
25 mm
MAX
19 mm
MAX

63
© 2011 Somfy SAS. All rights reserved. 112011
EN
4. WIRING
M
Shared
Neutral
Earth
Motor
• Cut off the mains power supply.
This motor must not be connected to an isolati-
on transformer.
Only the io plate ref: 1811130 may be con-
nected to the J4 io motor.
• Connect the motor and plate assembly according to
the information in the table below:
• A maximum of 3 motors, with a total cable length of
50 m, can be connected in parallel. Live and neutral
must be connected together respectively.
230 V ~ 50 Hz
Neutral (N)
Live (P) Top
-
Plate cable
Blue
Black
-
1
2
3
Earth ( ) Yellow/Green
4
1
2
3
4
Plate
Mounting inside the head rail Mounting outside the head rail
• The mounting of the J4 io plate inside the head rail is compatible with the following head rails
and shafts:
In order to x the plate inside the head rail, you may use double sided adhesive tape ref: 9016646.
Mounting the plate with double sided adhesive tape is guaranteed to temperatures from -30°C
to 70°C. However, to ensure proper adhesion over time, it is essential to stick the tape to a
clean surface.
SHAFT
Up to 14 mm hex
Up to 14 mm square
Up to 14 mm diameter
HEAD RAIL
57 x 51 mm
58 x 56 mm
78 x 67 mm
65 x 64 mm

64 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
5. COMMISSIONING
Programming the rst
Somfy local control
point
Only one motor should be powered at a time.
Switch on and follow procedure "a" or "b"
depending on the reaction of the blind:
a) The blind moves briey
The end limits are set and no
Somfy control point has been stored.
Go to the section entitled 5.5 "Programming the rst
Somfy io local control point".
or
b) The blind does not move
Press the Up or Down buttons and follow
procedure "c" or "d" depending on the reaction of the
blind:
c) The blind still does not move
The end limits are not set and no
Somfy control point has been stored.
Go to the section entitled 5.2 "Pre-programming the
Somfy io local control point".
or
d) The blind is fully raised or lowered
The end limits are set and the
Somfy control point has been stored.
Go to the section entitled "Operation".
5.2. Pre-programming the Somfy io local control point
The guide only describes commissioning using a Situo mobile io VB type Somfy io local control point
which provides greater precision when tilting the slats.
For commissioning using any other io control point, refer to the corresponding guide.
5.1. Identifying setting steps already completed
• Press the Up and Down buttons simultaneously.
The blind moves briey, the Somfy local
io control point is pre-programmed to the motor.
Pre-programming the
Somfy io local control
point
Operation
c or d

65
© 2011 Somfy SAS. All rights reserved. 112011
EN
• Press the Up button:
a) If the blind raises, the direction of rotation is correct:
go to the section entitled 5.4 "Basic Settings".
b) If the blind lowers, the direction of rotation is incorrect:
press the "my" button until the blind moves, the direction
of rotation is modied.
• Press the Up button to check the direction of rotation.
5.4. Basic settings
5.3. Checking the motor's direction of rotation
5.4.1. Setting upper and lower end limits
Check that your J4 io actuator has been assembled in
the blind in the lowered position with the slats closed.
• Press the Up button for 3 seconds. The blind rotates in
the up direction.
• Stop the blind using the stop on the "mushroom" button.
The end limits are set. The upper end limit is stored on
the mushroom.
a
b
=
=
Setting the end limits
a
b
=
=

66 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
5.5. Programming the rst Somfy io local control point
5.5.1. Using a pre-programmed Somfy io local control point
(5.2)
Briey press the PROG button on this control point:
the blind moves briey, the control point has been
programmed.
5.5.2. After a power cut
• Press the Up and Down buttons on the new control point
simultaneously until the blind moves.
• Briey press the PROG button on this control point:
the blind moves briey; the control point has been
programmed.
5.6. Checking the settings
Check the settings of the upper and lower end limits using the Somfy io local control point.
5.4.2. Modifying the angular travel
For optimum operation of the J4 io actuator, it is
essential to adjust the angular travel.
The angular travel is the total angle necessary for the
blind to change from a slats closed position to a slats
fully open position.
The slats fully open position is reached when the slats
no longer tilt and the blind makes an initial raising
movement.
• Press the down button until the lowered position is
reached.
• When the blind is in the lowered position, press the Up
and Down buttons for 5 seconds: the blind moves
briey.
• Press the "my" button on the control point: the blind
moves briey.
• Move the slats from the slats closed position to the slats
fully open position by briey pressing the Up button on the
control point.
• Press the Up button and "my" buttons on the control
point at the same time, until the blind moves.
or
or

67
© 2011 Somfy SAS. All rights reserved. 112011
EN
7. MODIFICATION OF THE SETTINGS
7.1. Favourite position (my)
7.1.1. Modifying the favourite position (my)
• Place the blind in the required new favourite position (my).
• Press the "my" button until the blind moves: the new
favourite position (my) has been programmed.
7.1.2. Deleting the favourite (my) position
• Press the "my" button: the blind will start to move and
will stop in the favourite position (my).
• Press the "my" button again until the blind moves: the
favourite position (my) has been deleted.
6. OPERATING
6.1. Standard operation (the operation below is only possible with the following control
points: Situo mobile io VB, Easy Sun io, Composio io and Smoove io)
To use the favourite (my) position: Briey press the "my"
button: the blind starts to move, then stops and angles the
slats in accordance with the angle programmed for the
favourite (my) position.
6.1.2. STOP function
The blind is moving.
Briey press the "my" button: the blind stops automatically.
6.1.3. Up and Down buttons
A brief press on the Up or Down buttons causes the slats
of the blind to turn.
A long press on the Up or Down buttons will cause the
blind to raise or lower completely.
6.2. Operating with a Somfy sensor or automatic function
Refer to the corresponding manual for the Somfy io sensor.
6.1.1. Favourite position (my)
Besides the upper and lower positions, an intermediate position known as the "favourite posi-
tion (my)" may be programmed in the motor. The “my” favourite position is pre-set in the
factory, and corresponds to the “slats lowered, sun protection” position.
To modify or delete the favourite position (my), see the section entitled "Modifying settings".

68 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
7.3. Modifying the end limits
7.3.1. Modifying the upper end limit
• Place the blind in the intermediate position.
• Press the Up and Down buttons for 5 seconds the blind
moves briey.
• Press the Up button (The blind rotates, stops, then conti-
nues to turn in the up direction) until the required end of
travel is reached (The blind will continue to rise after the
control point is pressed for 3 seconds).
• Stop the blind in the required position (If the end of travel
has been set on the mushroom, the effective end of travel
will be stored slightly below the mushroom).
• Press the Down button.
The blind will move briey to conrm storage.
Note: If a new end of travel needs to be set beyond the
existing end of travel, the blind will stop itself at the
existing end of travel. It will be necessary to press the
control point again to go past this existing end of travel.
7.3.2. Modifying the lower end limit
• Place the blind in the intermediate position.
• Press the Up and Down buttons for 5 seconds the blind
moves briey.
• Press the Down button (the blind will turn, stop, then conti-
nue in the down direction) until the required lower end of
travel is reached (the blind will continue to lower when the
control point is pressed for 3 seconds).
• Stop the blind in the required position.
• Press the Up button.
The blind will move briey to conrm storage.
Note: If a new end of travel needs to be set beyond the
existing end of travel, the blind will stop itself at the
existing end of travel. It will be necessary to press the
control point again to go past this existing end of travel.
7.2. Adding/Deleting Somfy io control points and io sensors
Refer to the corresponding guide.

69
© 2011 Somfy SAS. All rights reserved. 112011
EN
7.4. Modifying the angular travel
For optimum operation of the J4 io actuator, it is
essential to adjust the angular travel.
The angular travel is the total angle necessary for the
blind to change from a slats closed position to a slats
fully open position.
The slats fully open position is reached when the slats
no longer tilt and the blind makes an initial raising
movement.
• Press the down button until the lowered position is
reached.
• When the blind is in the lowered position, press the Up
and Down buttons for 5 seconds: the blind moves
briey.
• Press the "my" button on the control point: the blind
moves briey.
• Move the slats from the slats closed position to the slats
fully open position by briey pressing the Up button on the
control point.
• Press the Up and "my" buttons on the control point at the
same time, until the blind moves.
or
or

70 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
8. TIPS AND RECOMMENDATIONS
8.1. Questions on the J4 io?
Observations Possible causes Solutions
The blind does not
operate.
The wiring is incorrect. Check the wiring and modify it if necessary.
The motor is hot. Wait until the motor cools down.
The Somfy io control point battery
is low. Check whether the battery is weak and replace it if necessary.
The control point is not compatible. Check for compatibility and replace the
control point if necessary.
The Somfy io control point used
has not been programmed into the
actuator.
Use a programmed control point or program
this control point.
The blind stops too
soon or too late. The end limits have been incorrectly
set. Readjust the end limits.
Despite the presence
of a sunlight sensor,
when the sunlight is
low the blind does
not tilt the slats to the
horizontal position.
The sensor is not paired/set. Read the sensor manual to carry out the
pairing and appropriate settings
The sensor is paired/set. Readjust the angular travel.
The "my" position is cleared. Set the "my" position.
I can't tilt the slats
easily. The remote control is not
compatible.
Pairing and using a Situo mobile io VB/Easy
Sun io/Composio io/Smoove io remote
control.
I can't tilt the slats
properly. The angular travel is incorrectly set. Readjust the angular travel.
The"my" position is
not working. The "my" position is cleared. Set the "my" position.
My "my" position
cannot be repeated. The angular travel is incorrectly set. Readjust the angular travel and then reset
the "my" favourite position.
The blind (or one of
several) does not
react as described
in the manual during
pairing or setting.
Pairing or setting has been not
executed correctly. Only cut shortly the power and repeat the procedure if necessary.

71
© 2011 Somfy SAS. All rights reserved. 112011
EN
8.2. Replacing a lost or broken Somfy io control point
Refer to the corresponding guide.
8.3. Replacing a component of the actuator
If necessary it is possible to physically replace the J4 io motor, the J4 io plate, or both.
In all circumstances, in order to have an operational installation, the following procedure must be
carried out:
• Connect the plate with the motor, then reconnect the mains power supply
• Carry out the procedure from the section "8.4 Return to factory conguration".
• Carry out the procedure in section "5 Commissioning".
Only switch off the power for the actuator to be reset.
• Place the blind in the intermediate position (if possible).
• Cut the power supply for 2 seconds.
• Switch the power supply back on for 5 to 15 seconds.
• Cut the power supply for 2 seconds.
• Switch the power supply back on: the blind starts to move
for a few seconds.
If the blind is at the upper or lower end limit, it will move
briey.
• Hold down the PROG button for 7 seconds: the blind will
move once then again a few moments later. The actuator
is in factory conguration.
Repeat the procedures from the "Commissioning" section
8.4. Restoring the original conguration
2 sec.
2 sec.
15 sec.
5 sec.
OFF
OFF
ON
ON
my
This reset deletes all control points, all the sensors and all the end limit settings, and resets
the actuator's direction of rotation and favourite position "my".
The current position during the reset then becomes the new lower end limit position.
The upper end limit is cleared.
The favourite position of the actuator is reset to 600 ms from the lower end limit position.
The direction of rotation of the actuator is that specied in section 5.
The value of the angular travel is reset to the default value (180° rotation of the motor shaft).

72 © 2011 Somfy SAS. All rights reserved. 11/2011
EN
9. TECHNICAL DATA
Radio frequency 868-870 MHz io-homecontrol®, two-way Tri-band
Power supply 230 V ~ 50 Hz
Operating temperature - 20°C to + 70°C
Protection rating (J4 io motor) IP 54
Protection rating (J4 io plate) IP 67
Maximum number of associated control
points and sensors 9
Maximum end of travel cage capacity
(in turns) 200
Factory set end of travel cage capacity
(in turns) 120
Safety level (J4 io motor) Class I
Safety level (J4 io plate) Category II
Torque (Nm) 610 18
Motor length (mm) 306 321 341
Thermal time
J4 io motors are protected by a thermal cut-out in case of overheating caused by continuous use for
longer than 6 minutes.
Head rail breakdown
For detailed technical information, refer to the specications sheets and dedicated interface plans.
1TN
2TN
HTM
WT
20 min
26 min
Motor tilt
The J4 io motor has been designed to operate horizontally:
NOK OK OK 10°
max
For the J418, the maximum permissible torque for an end of the motor shaft is 12 Nm.

73
© 2011 Somfy SAS. All rights reserved. 112011
EN

www.somfy.com
Somfy
50 Avenue du Nouveau Monde
BP 152 - 74307 Cluses Cedex
France
T [phone]
F [phone]
Somfy Worldwide
Argentina:
Somfy Argentina
Tel: [phone]
Australia:
Somfy PTY LTD
Tel: [phone]
Austria:
Somfy GesmbH
Tel: +43 (0) 662 / 62 53
08 - 0
Belgium:
Somfy Belux
Tel: [phone]
Brasil:
Somfy Brasil Ltda
Tel: [phone]
Canada:
Somfy ULC
Tel: [phone]
China:
Somfy China Co. Ltd
Tel: [phone]
Croatia :
Somfy Predstavništvo
Tel: [phone]
Cyprus :
Somfy Middle East
Tel: [phone]
Czech Republic:
Somfy, spol. s.r.o.
Tel: [phone]
Denmark:
Somfy Nordic Danmark
Tel: [phone]
Export:
Somfy Export
Tel: + 33 (0)4 50 96 70 76
Tel: + 33 (0)4 50 96 75 53
Finland:
Somfy Nordic AB Finland
Tel: [phone]
Fax: [phone]
France :
Somfy France
Tel. : [phone]
Germany:
Somfy GmbH
Tel: [phone]
Greece:
SOMFY HELLAS S.A.
Tel: [phone]
Hong Kong:
Somfy Co. Ltd
Tel: [phone]
Hungary :
Somfy Kft
Tel: [phone]
India:
Somfy India PVT Ltd
Tel : +(91) 11 4165 9176
Indonesia:
Somfy Jakarta
Tel: +(62) 21 719 3620
Iran:
Somfy Iran
Tel: [phone]
Italy:
Somfy Italia s.r.l
Tel: [phone]
Japan:
SOMFY KK
Tel: [phone]
Jordan:
Somfy Jordan
Tel: [phone]
Kingdom of Saudi Arabia:
Somfy Saoudi
Riyadh :
Tel: [phone]
Tel: [phone]
Jeddah :
Tel: [phone]
Kuwait:
Somfy Kuwait
Tel: [phone]
Lebanon:
Somfy Lebanon
Tel: [phone]
Malaisia:
Somfy Malaisia
Tel:[phone]
Mexico:
Somfy Mexico SA de CV
Tel: [phone]
Morocco:
Somfy Maroc
Tel: [phone]
Netherlands:
Somfy BV
Tel: [phone]
Norway:
Somfy Nordic Norge
Tel: [phone]
Poland:
Somfy SP Z.O.O.
Tel: [phone]
Portugal:
Somfy Portugal
Tel. [phone]
Romania:
Somfy SRL
Tel.: +40 - (0)368 - 444 081
Russia:
Somfy LLC.
Tel: [phone]
Serbia:
SOMFY Predstavništvo
Tel: 00381 (0)25 841 510
Singapore:
Somfy PTE Ltd
Tel: [phone]
Slovak republic:
Somfy, spol. s r.o.
Tel: [phone]
Tel: [phone]
South Korea:
Somfy JOO
Tel: [phone]
Spain:
Somfy Espana SA
Tel: [phone]
Sweden:
Somfy Nordic AB
Tel: [phone]
Switzerland: Somfy A.G. -
Tel: [phone]
Syria: Somfy Syria
Tel: [phone]
Taïwan:
Somfy Development and
Taiwan Branch
Tel: [phone]
Thailand:
Bangkok Regional Ofce
Tel: [phone]
Tunisia:
Somfy Tunisia
Tel: [phone]
Turkey:
Somfy TurkeyMah.,
Tel: [phone]
30 15
United Arab Emirates:
Somfy Gulf Jebel Ali Free
Zone
Tel: [phone]
United Kingdom:
Somfy Limited
Tel: [phone]
United States:
Somfy Systems
Tel: [phone]
Somfy SAS, capital 20.000.000 Euros, RCS Annecy 303.970.230 - 09/2011