SOMFY Situo 5 Variation RTS User manual

Continued On Next Page
Situo®5 Variation RTS
Wall Mounting the Situo 5 Variation
Introduction
Part Number:
1811612
The Situo 5 Variation RTS provides 5 channels for precise individual
and group incremental control of motorized window coverings.
• Peel • Adhere • Hang
A. Wall mounting recess
B. Up/Open button
C. STOP/”my” button
D. Tilt/Scroll Wheel
E. Down/Close button
F. Channel indicator lights
G. Channel selector
Using the included Mounting Bracket:
• Peel the protective film from the adhesive on the back
of the wall mounting bracket.
• Adhere the wall mounting bracket to a flat, clean,
and dry surface (press firmly).
• Hang the Situo 5 Variation on the wall mounting bracket.
• Optional: Can also be screwed/anchored to wall.
H. Programming (PROG)
button on back

Battery Replacement
• Slide to remove rear panel from remote control.
• Insert new CR2430 battery as specified.
• Replace rear panel on remote control.
Battery
compartment
located on back.
Adding/Deleting a Situo 5 Variation RTS
To add or delete from a window covering:
Using the control already associated with the window covering:
• Press and hold the PROG button (H) until
the window covering briefly moves up and down.
On the Situo 5 Variation RTS to be added or deleted:
• Select the appropriate channel (G).
• Briefly press the PROG button (H), the window covering
briefly moves up and down and the Situo 5 Variation RTS is
added or deleted.
Programming a Replacement remote:
Using the programming button on the drive head:
• Press and hold the drive head programming button until
the motorized product briefly moves up and down.
• Briefly press the PROG button (H) on the control
to add or delete. Green LED blinks 5 times.
You now have control over the window covering with replacement remote
G
H
CR2430
Continued On Next Page

This product is intended for indoor use only.
Please keep out of reach of children. Avoid
damaging product by dropping or using undo
force. Do not expose product to open flame,
heat, or moisture.
Operation
1
2
3
4
5
F
G
Channel Selector (G)
Before operating the Situo 5 Variation RTS, ensure the correct channel
has been selected.
• Briefly press the channel selector button (G) to choose the
correct channel.
• The selection indicator lights (F) correspond to channels
1 through 4.
• Channel 5 is selected when all indicator lights are on.
Arrow Buttons (B)
Depending on the type of window covering to be operated:
• Up/Open
• Down/Close
Stop button/“my” (C)
• Press the “my” button to stop the window covering action.
• If the window covering action has been stopped, press either
UP or DOWN button on transmitter to activate in the desired
direction OR press “my” button to activate motorized window
covering to the pre-programmed “my” position.
Setting, modifying, or deleting the favorite preset
position “my”. (C)
• Place the window covering in the desired position then press
and hold “my” button for approximately 5 seconds to set the
favorite position.
• To delete the favorite preset position, place the window covering
in the established favorite position “my” and press and hold “my” button
for approximately 5 seconds.
How to Operate "my" Position. (C)
• The window covering will return to this position whenever you press “my” in the future.
• If the window covering is currently in motion, press the “my” button twice
– once to stop it and once again to return it to the “my” position.
Tilt/Scroll Wheel (D)
• Used to adjust the slats on blinds and varying light and heat levels.
• Scrolling one notch at-a-time will open or close the slats accordingly.
F
G
AS WITH ANY PRODUCT INVOLVING ELECTRICAL POWER, CAUTION MUST BE USED AT ALL TIMES.
PLEASE CAREFULLY READ AND FOLLOW ALL OF THE INSTRUCTIONS.
This device is FCC certified and complies with part 15 of the FCC rules.
RTS compatibility: RTS transmitters are capable of operating any RTS motor.
Note: Visit https://store.somfysystems.com/ to
purchase an additional or replacement product.
C-0052 11/2021