Sonova PHONAK SDS 4.0 User manual

SDS 4.0 Reference Guide

1
Important information 2
SDS 4.0 Fit and Go Box overview 3
Selecting the receiver length 4
Choosing the correct earpiece for the receiver 5
Attaching / removing the retention to/ from the receiver 6
Attaching the dome to the receiver 7
Attaching the SlimTip to the receiver 8
Removing the SlimTip from the receiver 9
How to exchange the receiver 10
Maintenance of domes and custom ear pieces 11
CeruShield™ Disk — wax protection system for SDS 4.0 receivers 12
Content

2
Important information
Hearing instruments should not be fitted with domes/wax
protection system when used by patients with perforated
eardrums, inflamed ear canals or otherwise exposed
middle ear cavities. In these cases, we recommend the
use of a custom earpiece.
In the unlikely case that any part of the system remains
in the ear canal, it is strongly recommended to consult a
medical specialist for safe removal.
•The dome should be changed every three months or when
it becomes stiff or brittle. This is to prevent the dome from
detaching from the receiver sound outlet during insertion
into or removal from the ear.
•Changes or modifications made to this equipment not
expressly approved by Phonak are not allowed.
Thank you for choosing a Phonak Receiver-In-Canal (RIC)
product, designed to provide comfortable, flexible fittings
for your patients.
These assembly instructions provide you with a straight-forward
approach to fitting Phonak RIC hearing instruments for
long-term satisfaction.
Please note that all SDS 4.0 components
are only compatible with Phonak Audéo™
Marvel devices.

3
SDS 4.0 Fit and Go Box overview
S Receiver
OR 054-0778
OL 054-0777
S Receiver
1R 054-0780
1L 054-0779
S Receiver
2R 054-0782
2L 054-0781
S Receiver
3R 054-0784
3L 054-0783
CeruShield™ Disk
098-0445
M Receiver
OR 054-0802
OL 054-0801
M Receiver
1R 054-0804
1L 054-0803
M Receiver
2R 054-0806
2L 054-0805
M Receiver
3R 054-0808
3L 054-0807
P Receiver
OR 054-0813
OL 054-0812
Retention S Receiver
004-8596-001
Retention M Receiver
004-8597-001
Retention P Receiver
004-8623-001
Vented dome S
054-0809 Measurement tool for cable length
026-0697
Receiver Handling Tool for SlimTips 4.0
026-1119
Vented dome M
054-0810 Pin removal tool
002-0404-1
Vented dome L
054-0811
Power dome S
054-0820
Power dome M
054-0821
Power dome L
054-0822
P Receiver
1R 054-0815
1L 054-0814
P Receiver
2R 054-0817
2L 054-0816
P Receiver
3R 054-0819
3L 054-0818
Cap dome
054-0788
Open dome S
054-0785
Open dome M
054-0786
Open dome L
054-0787

4
1. Position your head at the same horizontal level as the patient’s
head so you are looking straight into the patient’s ear. (a)
2. Hold the measurement tool with the appropriate blue or
red color code marking so your thumb is placed on the
colored area. (b)
3. Place the measurement tool on the top of the ear. Keep the
lines on the measurement tool horizontal. (b)
4. Choose the number (0, 1, 2, or 3) on the measurement tool
which is closest to the top of the opening of the ear canal.
In this example, 0 would be the most accurate choice. (c)
5. For binaural fittings, repeat process on the opposite ear.
Note:
It is important to measure both ears for a binaural fitting since right and
left ear sizes can vary and may require different receiver lengths.
0
1
2
3
b
a
c
right left
Selecting the receiver length

5
Dome size
Perform an otoscopic examination of your patient’s ear canal. Based on the
examination, choose a dome size diameter and length suitable for the ear canal.
The dome should fit snugly and comfortably into the opening of the patient’s ear
canal, shown in the figure, and help to retain the receiver inside.
*There are no coupling instructions for cShell as it is pre-assembled. Receiver with cShell can only be exchanged by Phonak.
Choosing the correct earpiece for the receiver
Domes Custom ear pieces
Cap Open Vented Power SlimTip cShell*
• Instant fit
• Open fit
• One size only
• Instant fit
• Open fit
• Sizes S, M, L
• Instant fit
• Semi-occluded fit
• Wider fitting range
than Open dome
• Sizes S, M, L
• Instant fit
• Occluded fit
• Expanded low
frequency response
• Sizes S, M, L
• Custom fit
• Choice of venting
• Impression required
• SlimTip available in Acrylic and
Titanium material
• RIC SecureFit mold is available in Silicone
• cShell available in Acrylic only

6
Removing the retention
We recommend using the retention piece for a
more stable positioning of the receiver in the ear
canal. It can easily be pre-shaped to the concha
by sliding it over a solid edge.
Attaching / removing the retention to/ from the receiver
1. Hold receiver rmly with one hand.
1. Hold the receiver rmly in one
hand with the receiver name
(e.g. 0M) facing upwards. With
the other hand hold the retention
at the base of the lament.
Attaching the retention
2. Slide the retention over the
receiver spout until you feel it
click into place. The receiver
name should still be clearly visible.
2. Slide the retention forwards over
the receiver spout.

7
Attaching the dome to the receiver
1. Hold the receiver in one hand and the dome in
the other hand.
2. Slide the dome over the receiver spout.
You will feel the dome “click” into place.
In very rare cases, the dome can remain in the
ear canal when removing the receiver from the
ear. In the unlikely case that any parts remain
in the ear canal, it is strongly recommended to
see a medical specialist for safe removal.

8
Attaching the SlimTip to the receiver
1. Slide the receiver into the sleeve of the handling
tool, ensure the receiver label (e.g. 0M) is visible
and facing upwards, and the receiver cable is
extending upwards. Note that the tool has three
dierent sized sleeves to accommodate S, M and
P receiver housings.
3. Gently insert the receiver spout into the SlimTip Link
until you feel it click into place securely.
2. Hold the SlimTip rmly with one hand, with the
other hand insert the receiver using the handling
tool. Note that the printed label on the SlimTip
faces the opposite direction to the receiver label.
4. Gently slide the tool away from the receiver.