Sony MVE-8000 User manual

DME PROCESSOR PACK
MVE-8000
OPERATION MANUAL [English]
1st Edition (Revised 1)
MKS-8810M MKS-8820M MKS-8830M
MULTI FORMAT DME PROCESSOR
MKS-8800

2
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
THIS APPARATUS MUST BE EARTHED.
For the customers in the USA
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with the
limits for a digital device pursuant to Subpart B of Part 15 of
FCC Rules.
This symbol is intended to alert the user to the
presence of important operrating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: THIS WARNING IS APPLICABLE FOR USA
ONLY.
If used in USA, use the UL LISTED power cord specified
below.
DO NOT USE ANY OTHER POWER CORD.
Plug Cap Parallel blade with ground pin
(NEMA 5-15P Configuration)
Cord Type SJT, three 18 AWG wires
Length Less than 2.5 m (8 ft 3 in)
Rating Minimum 10 A, 125 V
Using this unit at a voltage other than 120V may require the
use of a different line cord or attachment plug, or both. To
reduce the risk of fire or electric shock, refer servicing to
qualified service personnel.
When using a LAN cable: For safety, do not connect to the
connector for peripheral device wiring that might have
excessive voltage.
Um Feuergefahr und die Gefahr eines
elektrischen Schlages zu vermeiden, darf
das Gerät weder Regen noch Feuchtigkeit
ausgesetzt werden.
Um einen elektrishen Schlag zu vermeiden,
darf das Gehäuse nicht geöffnet werden.
Überlassen Sie Wartungsarbeiten stets nur
qualifiziertem Fachpersonal.
DIESES GERÄT MUSS GEERDET
WERDEN.
Afin d’éviter tout risque d’incendie ou
d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution,
garder le coffret fermé. Ne confier
l’entretien de l’appareil qu’à un personnel
qualifié.
CET APPAREIL DOI ÊTTRE RELIÉ À LA
TERRE.
For the customers in Europe (MKS-8800 only)
This product with the CE marking complies with both the EMC
Directive (89/336/EEC) and the Low Voltage Directive (73/23/
EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the
following European standards:
• EN60950: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment: E4 (controlled EMC
environment, ex. TV studio).
WARNING
VORSICHT
AVERTISSEMENT

3
Für Kunden in Europa (nur MKS-8800)
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt
sowohl die EMV-Direktive (89/336/EEC) als auch die Direktive
Niederspannung (73/23/EEC) der EG-Kommission.
Die Erfüllung dieser Direktiven bedeutet Konformität für die
folgenden Europäischen Normen:
•EN60950: Produktsicherheit
•EN55103-1: Elektromagnetische Interferenz (Emission)
•EN55103-2: Elektromagnetische Empfindlichkeit
(Immunität)
Dieses Produkt ist für den Einsatz unter die folgende
elektromagnetische Bedingung ausgelegt: E4 (kontrollierter
EMV-Bereich, z.B. Fernsehstudio).
Pour les clients européens (MKS-8800 uniquement)
Ce produit portant la marque CE est conforme àla fois àla
Directive sur la compatibilitéélectromagnétique (EMC) (89/
336/CEE) et àla Directive sur les basses tensions (73/23/
CEE) émises par la Commission de la Communauté
européenne.
La conformitéàces directives implique la conformitéaux
normes européennes suivantes:
•EN60950: Sécuritédes produits
•EN55103-1: Interférences électromagnétiques (émission)
•EN55103-2: Sensibilitéélectromagnétique (immunité)
Ce produit est prévu pour être utilisédans l’environnement
électromagnétique suivant: E4 (environnement EMC contrôlé
ex. studio de télévision).
For the customers in Europe (MKS-8810M/8820M/8830M
only)
This product with the CE marking complies with the EMC
Directive (89/336/EEC) issued by the Commission of the
European Community.
Compliance with this directive implies conformity to the
following European standards:
•EN55103-1: Electromagnetic Interference (Emission)
•EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment: E4 (controlled EMC
environment, ex. TV studio).
Für Kunden in Europa (nur MKS-8810M/8820M/8830M)
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die
EMV-Direktive (89/336/EEC) der EG-Kommission.
Die Erfüllung dieser Direktive bedeutet Konformität für die
folgenden Europäischen Normen:
•EN55103-1: Elektromagnetische Interferenz (Emission)
•EN55103-2: Elektromagnetische Empfindlichkeit
(Immunität)
Dieses Produkt ist für den Einsatz unter die folgende
elektromagnetische Bedingung ausgelegt: E4 (kontrollierter
EMV-Bereich, z.B. Fernsehstudio).
Pour les clients européens (MKS-8810M/8820M/8830M
uniquement)
Ce produit portant la marque CE est conforme àla Directive
sur la compatibilitéélectromagnétique (EMC) (89/336/CEE)
émise par la Commission de la Communautéeuropéenne.
La conformitéàcette directive implique la conformitéaux
normes européennes suivantes:
•EN55103-1: Interférences électromagnétiques (émission)
•EN55103-2: Sensibilitéélectromagnétique (immunité)
Ce produit est prévu pour être utilisédans l’environnement
électromagnétique suivant: E4 (environnement EMC contrôlé
ex. studio de télévision).
Periodic inspections
To guarantee safe long-term operation, periodic inspections
are recommended. Please contact your Sony representative
for detailed information about the content and cost of periodic
inspections.

4Table of Contents
Table of Contents
Overview ............................................................................... 5
Features......................................................................................5
Overview of the MVE-8000 Components.................................5
Location and Function of Parts...........................................6
Front Panel................................................................................ 6
Rear Panel................................................................................. 7
Example System Configuration ..........................................9
MVS-8000 System Configuration ............................................ 9
Flow of Video Signals ............................................................ 10
Power Supply Unit Status Indicator..................................11
Specifications ..................................................................... 12
MKS-8800 Multi Format DME Processor ..............................12
MKS-8810M Basic Effects Board...........................................12
MKS-8820M Input/Output Board ...........................................13
MKS-8830M Nonlinear Effect Board .....................................13

5
Overview
Overview
The Sony MVE-8000 DME Processor Pack is a
multifunction digital video effects unit for use in a system
configured around an MVS-8000 Multi Format Switcher
System.
The MVE-8000 is a generic name of the DME processor
unit having option boards installed in it.
Features
Multi format support
This unit supports both HDTV and SDTV signal formats,
which can be easily selected from the center control panel
for the MVS-8000 system without exchanging expansion
boards. The wide range of supported signal formats allows
the unit to be used in many different video production
environments. The following signal formats are supported.
• SDTV formats: 480i/59.94, 576i/50
• HDTV formats: 1080i/50, 1080i/59.94, 1080i/60,
1080p/23.976sF, 1080p/24sF, 1080p/25sF, 1080p/
29.97sF, 1080p/30sF
Rich variety of effects
The unit supports a wide variety of effects and functions
such as 3D linear transforms (including expand and
reduce) and borders. The effects and functions supported
are as follows.
• 3D linear transforms (expand, reduce, move, rotate)
• Border / Crop
• Defocus / Blur
• Multi-move
• Color modifiers (sepia, monochrome, negative,
posterization, solarization, contrast)
•Mosaic
• Freeze
• Lighting
•Trail
• Background
• Graphics display
• Drop shadow (2-channel effect)
• Combine (2-channel or 3-channel effect)
• Brick (3-channel effect)
Up to four DME channels in a single unit
DME boards can be installed to enable up to four
independent DME channels in a single unit, for space
savings and energy efficiency. Because there are multiple
internal channels, 2-channel and 3-channel effects can be
applied without making any special connections.
Linked operation with switcher processor
This unit is connected to the MVS-8000 Multi Format
Switcher Processor by a special cable, which allows DME
wipes, processed keys and a wide variety of other DME
effects to be used as if they were switcher functions. All
DME operations can be controlled from the MVS-8000
system’s center control panel.
Overview of the MVE-8000
Components
MKS-8800 Multi Format DME Processor
This is a cabinet (size: EIA 5RU) in which to install option
boards to provide multi-format DME processing
capabilities.
The option boards are as follows.
a) At least one board is required.
b) This board is always required.
c) One board is required per MKS-8810M board installed.
MKS-8810M Basic Effects Board
This board enables 1-channel DME effects. At least one
board is required. Up to four boards can be installed to
provide 4-channel DME effects.
MKS-8820M Input/Output Board
This board enables input and output of video signals
between the MVE-8000 and the MVS-8400/8300/8200
Switcher Processor Pack.
MKS-8830M Nonlinear Effect Board
This board enables nonlinear effects such as page turn and
ripple. It is used in combination with the MKS-8810M
board.
Note
When installing the MKS-8830M board, install it on all
installed MKS-8810M boards.
Optional accessories
RMM-10 Rack Mount Kit
Board name Maximum installable number of boards
MKS-8810M 4 a)
MKS-8820M 1 b)
MKS-8830M 4 c)

6Location and Function of Parts
Location and Function of Parts
Front Panel
POWER switch and status indicator
The POWER switch turns the unit on and off. The unit is
powered on when the POWER switch is on the “?”side,
and powered off when the POWER switch is on the “a”
side. The status indicator lights in green when the unit is
powered on.
Note
If the status indicator does not light when you turn the
POWER switch on, there may be a fault in the power
circuits. Turn the POWER switch off and contact your
Sony service representative.
POWER switch and status indicator
POWER

7
Location and Function of Parts
Rear Panel
a
aa
aSWITCHER (switcher I/O) A and B connectors
(MDR 68-pin) (MKS-8820M)
Connect with the supplied special cable to the DME 1A
and 1B connectors of the MVS-8000 Multi Format
Switcher Processor.
Each connector handles two channels of video signal input
and output. Therefore, when this unit is configured for one
or two channels (with one or two MKS-8810M boards
installed), you do not need to connect the SWITCHER B
connector.
If you are connecting a second MVE-8000 Multi Format
DME Processor to the MVS-8000, connect the
SWITCHER A and B connectors on the second processor
to the DME 2A and DME 2B connectors on the MVS-
8000.
b
bb
b-
--
-
AC IN (AC power input) connector (3-pin)
Connect to 100 to 240 V AC power supply with the
optional AC power cord.
c
cc
cU
UU
U(signal ground) terminal
Connect to the system ground.
d
dd
dGPI (General Purpose Interface) connector (D-sub,
25-pin)
Connect to external devices for input and output of trigger
signals. Up to eight inputs and eight outputs are possible,
with input and output conditions set on the center control
panel.
e
ee
eEDITOR connector (D-sub, 9-pin, RS-422A)
Connect to control this unit from a BVE-9100 or other
editing control system.
EDITOR GPICTRLDATAREF IN
-AC IN
U
SWITCHER ASWITCHER B
2- AC IN connector
7DATA connector
8REF INPUT connectors
1SWITCHER A and B connectors a)
6CTRL connector
5EDITOR connector
4GPI connector
3U
UU
U
terminal
a) This figure shows the rear panel when one MKS-8810M is installed in the
unit.

8Location and Function of Parts
f
ff
fCTRL (control) connector (RJ-45)
Connect to an Ethernet switch*.
The MVS-8000 Multi Format Switcher Processor and the
MVS-8000 system’s center control panel are connected in
the same way to the Ethernet switch to form a network for
exchange of signals between the devices.
This network is used primarily to control the various
devices from the center control panel.
* For information about Ethernet switches that can be used in an MVS
system, contact your Sony service representative.
For detailed information about setting up the Ethernet
switch, refer to the documentation supplied with the
switch.
For more information about Ethernet switch connectors,
see “MVS-8000 System Configuration” (page 9).
g
gg
gDATA connector (RJ-45)
Connect to an Ethernet switch.
The MVS-8000 Multi Format Switcher Processor and the
MVS-8000 system’s center control panel are connected in
the same way to the Ethernet switch to form a network for
exchange of signals between the devices.
This network is used primarily for exchange of various
types of data (key frame effects, snapshots, etc.).
h
hh
hREF INPUT (reference video signal input)
connectors (BNC type)
If you wish to synchronize this unit to an external reference
signal, input the reference signal. For an HDTV system,
input an HD tri-level sync signal, black burst signal, or
analog sync signal. For an SDTV system, input a black
burst signal or analog sync signal.
The two connectors have a loop-through configuration.
Signal input to one connector can be output from the other
connector. If you will not be using the loop-through
output, be sure to terminate the unused connector with the
supplied 75Ωterminator.

9
Example System Configuration
Example System Configuration
MVS-8000 System Configuration
CTRL
CTRL
EDITORDATA LAN
REMOTE
DATA CTRL REMOTE 1
DATA
PERIPH
PERIPH
Reference video signal b)
BVE-9100 Editing
Control System
Ethernet switch a)
MVE-8000 DME
Processor Pack
MKS-8010 System
Control Unit
Reference video
signal b)
BKS-R Series
HDS-X Series
Reference
video signal b)
Reference video
signal b)
Cross cable
Cable with BNC
connectors
MVS-8400/8300/8200 Switcher Processor Pack
Ethernet switch a)
VTR DDR Audio Mixer
a) It is recommended that the CTRL and DATA
LAN networks be configured by connecting
separate Ethernet switches for each LAN.
However, it is also possible to make connections
for both LANs on a single Ethernet switch.
b) Terminate with the supplied 75Ωterminators.
Terminators are supplied in the product
package.
DCU-8000 Device Control Unit Pack

10 Example System Configuration
SWITCHER B
DME 1B
PRIMARY INPUTS
1 to 68
PRIMARY INPUTS
69 to 80
OUTPUTS 1 to 48
DME 1A
MONITOR OUTPUTS
1 to 8
SWITCHER A
Flow of Video Signals
MVE-8000 DME Processor Pack
Reference video signal c)
Camera,
VTR,
routing
switcher
Monitor
Monitor
VTR
MVS-8400/8300/8200
Switcher Processor Pack
100 to 240 V AC power supply b)
100 to 240 V AC power supply b)
AC power supply
Reference video signal c)
100 to 240 V AC power supply a)
100 to 240 V AC power supply b)
100 to 240 V AC power supply b)
Video input signal
Video output signal
Video/key signal
Cable with 75-pin connectors
a) For the AC power cord of this unit, see “Accessories not supplied”
(see page 12) in this manual.
b) For the AC power cord of the MVS-8000, refer to “Accessories not
supplied”in the MVS-8400/8300/8200 Operation Manual.
c) Terminate with the supplied 75Ωterminators. Terminators are
supplied in the product package.

11
Power Supply Unit Status Indicator
Power Supply Unit Status
Indicator
The power supply unit status indicator shows the status of
the power supply unit during operation and when the unit
is powered on. Whenever a power error is detected, it is
reflected immediately by the indicator.
Meaning of status indicator displays
Indicator
color Status Description Steps to take
Green Lit Operating normally −
Red LIt Power supply unit fan
fault
Exchange the
fan unit
−Not lit Power supply unit
fault
Exchange the
power unit

12 Specifications
Specifications
The following specifications show the reference
performance for this unit and individual option boards.
Design and specifications are subject to change without
notice.
MKS-8800 Multi Format DME
Processor
General
Power requirements
100 to 240 V AC ±10%, 50/60 Hz
Peak inrush current
(1) Power ON, current probe method:
60 A (100 V), 60 A (230 V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1: 40 A
(230 V)
Power consumption
Approx. 3.5 to 1.5 A
Performance temperature
5ºC to 40ºC (41ºF to 104ºF)
Operating temperature
10ºC to 35ºC (50ºF to 95ºF)
Storage temperature
−20ºC to +60ºC (−4ºF to +140ºF)
Operating humidity
10% to 90%
Dimensions (w/h/d, excluding projections)
440×221×520 mm
(17 3/8×8 3/4×20 1/2inches)
Mass Approx. 20 kg (44 lb 1 oz)
(when equipped with all installable
option boards)
Reference input
REF IN BNC type, 75Ωwith loop-through output
HDTV systems: HD tri-level sync/SDTV
analog black burst/SDTV analog sync
SDTV systems: Analog black burst/
analog sync
Control connectors
CTRL RJ-45
Complies with 100 Base-TX standard
DATA RJ-45
Complies with 100 Base-TX standard
EDITOR D-sub 9-pin, female
Complies with RS-422A standard
Data transfer rate: 38.4 Kbps
GPI D-sub 25-pin, female
TTL inputs: 8
Relay contact outputs: 4
(30 V AC/DC, 0.1 A)
Open collector outputs: 4
AC input
AC IN 3-pin AC connector
System Delay
System delay 1 frame
Accessories supplied
MDR 68-pin cable (2)
75Ωterminator (1)
Operation Manual (1)
Installation Manual (1)
Accessories not supplied
AC power cord (for USA and Canada only) (125 V 10 A
2.4 m (8 ft)) (Part No.: 1-557-377-11)
AC power cord (for Europe only) (250 V 10 A 2.4 m
(8 ft)) (Part No.: 1-782-929-21)
MKS-8810M Basic Effects Board
Power requirements
12 V DC
Power consumption
Approx. 4.3 A
Dimensions (w/d)
317×380 mm (12 1/2×15 inches)
Mass Approx. 1.1 kg (2 lb 6 oz)
Accessories supplied
Operation and Installation Guide (1)
(supplied only when product is
purchased separately)

13
Specifications
MKS-8820M Input/Output Board
General
Power requirements
12 V DC
Power consumption
Approx. 4.1 A
Dimensions (w/d)
VIF board: 317×380 mm
(121/2×15 inches)
CN board: 278×94 mm
(11×3 3/4inches)
Mass Approx. 1.4 kg (3 lb 1 oz)
Video signal inputs and outputs
SWITCHER A, SWITCHER B
Connectors: MDR 68-pin
Signal format: LVDS (special format)
Accessories supplied
Operation and Installation Guide (1)
(supplied only when product is purchased separately)
MKS-8830M Nonlinear Effect Board
Power requirements
1.8 V DC, 3.3 V DC
Power consumption
Max. 20 W
Dimensions (w/d)
139×116 mm (51/2×45/8inches)
Mass Approx. 0.2 kg (7 oz)
Accessories supplied
Operation and Installation Guide
(supplied only when product is purchased separately)

14 Specifications

The material contained in this manual consists of information
that is the property of Sony Corporation and is intended solely
for use by the purchasers of the equipment described in this
manual.
Sony Corporation expressly prohibits the duplication of any
portion of this manual or the use thereof for any purpose other
than the operation or maintenance of the equipment described
in this manual without the express written permission of Sony
Corporation.
Le matériel contenu dans ce manuel consiste en informations
qui sont la propriétéde Sony Corporation et sont destinées
exclusivement àl’usage des acquéreurs de l’équipement
décrit dans ce manuel.
Sony Corporation interdit formellement la copie de quelque
partie que ce soit de ce manuel ou son emploi pour tout autre
but que des opérations ou entretiens de l’équipement àmoins
d’une permission écrite de Sony Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind, und
ausschließlich zum Gebrauch durch den Käufer der in dieser
Anleitung beschriebenen Ausrüstung bestimmt sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als die
Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche schriftliche
Erlaubnis der Sony Corporation.

Sony Corporation
B & P Company
Printed in Japan
2001.09.13
© 2001
MVE-8000
(WW)
3-206-007-02 (1) Printed on recycled paper
http://www.sony.net/