Soundcore Life Dot 2 NC User manual

USER MANUAL
Soundcore Life Dot 2 NC

01 EN
Charging
• Remove the protective lm from the earbuds before the rst use.
• Fully dry off the earbuds and the USB port before charging.
• Use a certied USB-C charging cable and charger to prevent any damage.
• Fully charge both the earbuds and the charging case before the rst use.
1. Place the earbuds in the charging case and close it.
The rst and the third LED indicators on the charging case will ash twice. This
conrms that the earbuds are being charged.
2. Connect the charging case to the power supply by using a USB-C charging cable.
The LED indicators on the charging case indicate the charging status.
2
1
< 30%
30% - 70%
> 70%
100%
3. To check the battery level of the charging case, open it to activate the LED
indicator.

EN 02
Soundcore App
Download the Soundcore app to enhance your experience.
User interface customization: In stereo mode, all of the controls (e.g. adjust volume,
control playback, activate Siri) can be customized in the app.
EQ settings: There are more than 20 EQ settings you can choose from in the app to
optimize your experience while enjoying different music genres.
Noise cancellation: Choose an active noise cancellation mode to reduce ambient
noise according to your surroundings.
• Transport: Targets low-end frequencies like engine and road noise for peaceful
journeys and commutes.
• Outdoor: Reduces ambient sounds in cities for less distractions.
• Indoor: Reduces voices and mid-frequency noise from coffee shops and other inside
spaces.
Transparency mode: Stay aware of your surroundings by allowing ambient sounds in.
• Fully Transparent: Hear all ambient sounds.
• Vocal Mode: Voices stand out more clearly from other ambient sounds.
Earbuds rmware update: You will be informed once the new version of rmware
is detected when you connect the earbuds with the app. Ensure the earbuds are
placed in the charging case and the case remains open until the rmware upgrade
is completed. During the upgrade, ensure the earbuds are being charged and avoid
any operation.

03 EN
Wearing
1. Choose the EarTips and EarWings that t your ears best.
2. Insert the earbuds into the inner canal of your ears and turn gently until you nd
the most comfortable and secure position.
Your earbuds come with multiple pairs of EarTips and EarWings, among which
Medium-sized are pre-installed.
Powering On/Off
Open the charging case, the earbuds will automatically power on.
The LED indicator on earbuds will light up white for 1 second.
To power off, place the earbuds in the charging case and close it.
ON
2
1
OFF

EN 04
When you’re wearing the earbuds, they will not power off until out of battery. When
you remove the earbuds, they will automatically power off after 30 minutes if no
device is connected.
Bluetooth Pairing
1. Open the charging case, the earbuds will automatically enter the Bluetooth pairing
mode.
The LED indicator on one earbud will flash quickly and on another earbud
breathe slowly.
2. Select “Soundcore Life Dot 2 NC” on your device’s Bluetooth list to connect.
When successfully connected, the LED indicator on earbuds will light up white
for 1 second and then turn off.
2
Soundcore
Life Dot 2 NC
Soundcore
Life Dot 2 NC
1
• Each time you power on your Soundcore earbuds, they will automatically connect
to your last successfully connected device if available within the Bluetooth range.
• Mono mode: When Bluetooth connected, you can use either one of the earbuds
only by placing the other one into the charging case and closing it.
• When powered on and connected, if either one of the earbuds is out of battery
and powered off, you can keep using the other one.
• When you are on a call, place either one of the earbuds into the charging case
and close it, the microphone in the other earbud will be activated.
• The right earbud is the primary earbud by default. If you want to change this,
remove the right earbud from your ear and leave the charging case open, the
microphone in the other earbud will be activated. Place the right earbud in the
charging case and close it, the left earbud will become the primary earbud.

05 EN
Pairing with another device
1. Place the earbuds in the charging case and leave the case open. Press and hold
the button on the case for 3 seconds until the earbud LED indicators ash white to
enter the pairing mode.
2. Select “Soundcore Life Dot 2 NC” on your device’s Bluetooth list to connect.
1 2
Soundcore
Life Dot 2 NC
Soundcore
Life Dot 2 NC
3”
Controls
Play/Pause Tap twice (R)
Next track Tap twice (L)
Answer a call
Tap twice (L/R)
Answer a second incoming call and put the
current call on hold
End/Reject a call
Press and hold for 2 seconds (L/R)
Switch between a call on hold and an active
call
Switch ambient sound modes
(Noise Cancellation/Normal) Press and hold for 2 seconds (L/R)

EN 06
Mono mode
Play/Pause Tap twice
Answer a call
End/Reject a call Press and hold for 2 seconds
Activate Siri or other voice assistant software
• All of the controls in stereo mode can be customized in the Soundcore app. In
mono mode, controls cannot be customized in the app.
• Adjust the volume level via the connected device or in the Soundcore app.
• In stereo mode, noise cancellation mode is set by default. Each time you power
on and connect, or switch to the stereo mode from mono mode, your earbuds
will restore the last setting.
• Noise cancellation or transparency mode is unavailable in mono mode.
Reset
You might need to reset your earbuds if you experience any connectivity problems
or function issues.
1. Place the earbuds in the charging case and leave the case open.
2. Press and hold the button on the case for 10 seconds until the earbud LED
indicators ash red 3 times and then turn white.
3. Wait until the LED indicator on one of the earbuds flashes fast while the other
breathes slowly. This conrms that the reset was successful and your earbuds can
be connected normally.
1 2
3
10”
3
The following two examples indicate the reset has not been successful and the
previous steps should be repeated.
• If only one earbud LED indicator ashes;
• If both earbud LED indicators ash quickly.

07 EN
Specifications
Specications are subject to change without notice.
Input 5 V 0.75 A
Rated output power 5 mW @ 1% THD
Battery capacity 55 mA x 2 (earbuds);
500 mA (charging case)
Charging time 2 hours
Playtime
(varies by volume level and content)
Up to 7 hours
(Total 35 hours with the charging case)
Playtime
(with ANC mode turned on) Up to 6 hours
(Total 30 hours with the charging case)
Playtime
(with transparency mode turned on)
Talk time Up to 5 hours
(Total 25 hours with the charging case)
Driver size 11 mm
Frequency response 20 Hz - 20 kHz
Impedance 16 Ω
Waterproof level (Earbuds) IPX5
Bluetooth version V 5.0
Bluetooth range 10 m / 33 ft