Soundstream RESERVE User manual

RESERVE
by
UPGRADE HEADUNIT FOR
2014+ HARLEY DAVIDSON®MOTORCYCLES
INSTALLATION GUIDE
To print a complete owners manual, visit us
online at motorcycleaudio.com/hdhu.14
- or -
Scan this QR code with your phone’s
camera to download the complete
owners manual to your phone.

REMOVAL OF ORIGINAL HEAD UNIT
STREET GLIDE
To prevent accidental vehicle start-up, which could cause death or serious injury,
remove main fuse/battery cables before proceeding.
1. Remove three outer fairing bolts using a T27 Torx screw driver.
The three outer fairing bolts are located below the windshield.
Remove the windshield, store it and the screws removed in a
safe place for re-installation later.
TIP: Reinstalling the center screw after removing the windshield
will prevent the outer fairing from falling during the next step. A
few turns by hand will be sucient.
2. Remove four inner fairing bolts using a T27 Torx screw driver. The four inner fairing bolts are located
adjacent to each turn indicator mounting bracket and below/adjacent to each speaker. Store these
screws in a safe place for re-installation later.
3. While straddling the front wheel fender, grasp the outer fairing, remove the center outer fairing bolt
from the previous step, then gently pull the fairing apart from the bike. With the fairing slightly pulled
away from the bike, disconnect wire harness for the headlamp and any other accessories. Lay the
fairing on a protected at surface to prevent damage.
4. Remove upper support bracket. Removal of the
upper support bracket requires removing 11 screws:
4.1) remove two screws attaching the
bracket to each speaker enclosure (1)
4.2) remove two screws attaching the
bracket to the inner fairing adjacent to
the gauge cluster (2)
4.3) remove four screws attaching the
bracket to the head unit chassis (3)
4.4) Remove one screw attaching the
bracket to the media compartment (6)
3
1
4
2

5. Disconnect electrical connections to the head unit.
5.1) Remove the main wire harness connector (1). To remove the main wire harness, depress
the latch lock with a small athead screwdriver and swivel the latch aside. Pull the wire harness
connector to remove from the socket.
5.2) Remove the USB cable connector (2). To remove the USB cable connector, depress the
locking tab with a small athead screwdriver. While depressing the locking tab, pull the USB
cable to release it from the socket.
5.3) Remove the radio antenna cable connector (3). To remove the radio antenna cable
connector, depress the locking tab with a small athead screwdriver. While depressing the
locking tab, pull the antenna cable to release it from the socket.
5.4) Remove the GPS antenna cable connector (4). To remove the GPS antenna cable
connector, depress the locking tab with a small athead screwdriver. While depressing the
locking tab, pull the GPS antenna cable to release it from the socket.
5.5) Remove SiriusXM antenna cable connector, if equipped (5). To remove the Sirius XM
antenna cable connector, depress the locking tab with a small athead screwdriver. While
depressing the locking tab, pull the Sirius XM antenna cable to release it from the socket.
6. Remove four head unit mounting screws using a 3/16” hex driver. Two screws are located at each
side of the head unit chassis. Store these screws in a safe place for re-installation later. Pull the head
unit assembly up and forward to remove.
1234 5

1. Detach each turn signal / indicator light by
removing the adjacent allen socket screw, using
a 3/16” allen head driver. Store these screws in a
safe place for re-installation later.
3. Remove four windshield bolts using a 1/8” allen
driver or Phillips screw driver and remove the
windshield. Also remove factory vent by pulling
straight up on the vent. The vent comes snapped
in place. Store the screws in a safe place for
installation later.
2. Remove four inner fairing bolts using a T25
Torx driver. Two inner fairing bolts are located
below each glove box, adjacent to each wind
deector. Store these screws in a safe place for
installation later.
4. After removing the vent, locate and unplug the
3-pin wire harness for the left and right side turn
signal indicator. These harness’ are adjacent to
each side of the head unit.
REMOVAL OF ORIGINAL HEAD UNIT
ROAD GLIDE
To prevent accidental vehicle start-up, which could cause death or serious injury,
remove main fuse/battery cables before proceeding.
5. Remove an additional inner fairing bolt with a T27 Torx or 5/32”
allen driver, one behind each speaker grill. Remove the speaker
grill by wedging a plastic/nylon pry tool between the inner fairing
and grill edge, popping it outward. Once these bolts are removed,
the outer fairing will be detached from the inner fairing. Store
these screws in a safe place for installation later.
6. While straddling the front wheel fender, grasp the
outer fairing. Gently pull the fairing apart from the
bike. With the fairing slightly pulled away from the
bike, disconnect wire harness for the headlamp or
any other accessories. Lay the fairing on a protected
at surface to prevent damage.
7. Remove two upper support bracket screws using a
3/16” allen driver. Store the bracket and screws in a
safe place for re-installation later.
2

8. Disconnect electrical connections to the head unit.
8.1) Remove the main wire harness connector (1). To remove the main wire harness, depress
the latch lock with a small athead screwdriver and swivel the latch aside. Pull the wire harness
connector to remove from the socket.
8.2) Remove the USB cable connector (2). To remove the USB cable connector, depress the
locking tab with a small athead screwdriver. While depressing the locking tab, pull the USB
cable to release it from the socket.
8.3) Remove the radio antenna cable connector (3). To remove the radio antenna cable
connector, depress the locking tab with a small athead screwdriver. While depressing the
locking tab, pull the antenna cable to release it from the socket.
8.4) Remove the GPS antenna cable connector (4). To remove the GPS antenna cable
connector, depress the locking tab with a small athead screwdriver. While depressing the
locking tab, pull the GPS antenna cable to release it from the socket.
8.5) Remove SiriusXM antenna cable connector, if equipped (5). To remove the Sirius XM
antenna cable connector, depress the locking tab with a small athead screwdriver. While
depressing the locking tab, pull the Sirius XM antenna cable to release it from the socket.
9. Remove four head unit mounting screws using a 3/16” hex driver. Two screws are located at each
side of the head unit chassis. Store these screws in a safe place for re-installation later. Pull the head
unit assembly up and forward to remove.
1234 5

OEM wire harness
HDHU.14 wire harness
INSTALLATION OF HDHU.14 HEADUNIT
To prevent accidental vehicle start-up, which could cause death or serious injury,
remove main fuse/battery cables before proceeding.
1. Install HDHU.14 into the location of the
OEM head unit. Secure the chassis to the
OEM mounting location with the four bolts
removed during the last step of REMOVAL OF
ORIGINAL HEAD UNIT section using a 3/16”
allen driver.
2. Connect the OEM USB and radio antenna cables disconnected during removal of the OEM head unit
to the matching sockets on the back of HDHU.14. If either are di󰀩cult to connect, verify the orientation
of the connector(s) is correct. If any aftermarket audio ampliers will be used in the audio system, take
a moment to connect the RCA cables to the corresponding audio outputs. Although not required, if the
Bluetooth calling microphone will be used, secure it to the desired installation location, then route its
cable to the corresponding input on the back of HDHU.14.
3. Insert and lock the male OEM head unit wire harness connector to the female socket of the included
wire harness for HDHU.14. Then, insert and lock the male connector of the HDHU.14 wire harness into
the corresponding female socket on the back of HDHU.14.
3.5mm Connection for Included
Bluetooth Calling Microphone
RCA Low-Level Subwoofer Output for
Aftermarket Subwoofer Amplier (RCA not incl.)
RCA Low-Level Rear Channel Output for
Aftermarket Speaker Amplier (RCA not incl.)
OE USB Cable Connector
(USB cable not included)
OE Radio Antenna Connector
(antenna cable not incl.) RCA Low-Level Front Channel Output for
Aftermarket Speaker Amplier (RCA not incl.)

4. If an alternative handlebar integration module other than Scosche is available, skip this step and
proceed to step 5. If included, connect the Scosche handlebar integration module to the corresponding
12-pin and 14-pin connectors on the wire harness of HDHU.14.
5. If an alternative handlebar integration module is available, cut the wires leading to the 12-pin and
14-pin connectors and discard them. Follow the color coded call-out below to connect the wires of
HDHU.14 wire harness to the corresponding inputs and outputs of the alternate handlebar control
module.
14-Pin Connector
Red..........................ACC turn-on
Orange....................Illumination
Violet/White.............CAN -
Green/White............CAN +
Black.......................Ground
Yellow......................12V
12-Pin Connector
Black/White..............Key/SWC Ground
Green/White.............Key/SWC 1
Grey/White...............Key/SWC 2
6. Double check all connections are complete and secure. Reassemble the fairing support bracket
using the original screws to the corresponding screw holes on top of HDHU.14. Then, reassemble the
fairing by reversing the model specic instructions covered in REMOVAL OF ORIGINAL HEAD UNIT.
SCOSCHE
2
ROAD GLIDE STREET GLIDE

LIMITED 90-DAY CONSUMER WARRANTY
LIMITED ONE-YEAR CONSUMER WARRANTY WITH PURCHASE AND INSTALLATION BY A
SOUNDSTREAM TECHNOLOGIES AUTHORIZED DEALER
Soundstream Technologies promises to the original purchaser to repair or replace this product with a
new or refurbished unit (at Soundstream Technologies sole and absolute discretion) should it prove to
be defective in workmanship or material under regular use, for a period of *ONE years from the date
of purchase from the Soundstream Technologies authorized dealer, PROVIDED the product was
purchased and installed by a Soundstream Technologies authorized dealer. During this *two-year
period, there will be no charge for product repair or replacement, PROVIDED the unit is returned to
Soundstream Technologies, return shipping pre-paid, along with the required proof of installation, the
bill of sale or other dated proof of purchase, and the consumer’s contact information.
If the unit is installed by anyone other than a Soundstream Technologies authorized dealer, the
warranty period will be 90-days from the date of purchase. This warranty is non-transferable and does
not apply to any unit modified or used in a manner contrary to its intended purpose. It does not cover
damage to the unit caused by installation or removal of the unit. During these 90 days, there will be
no charge for the repair or replacement PROVIDED the unit is returned to Soundstream
Technologies, return shipping prepaid, along with the bill of sale or other dated proof of purchase and
the consumer’s contact information.
This warranty is void if the product has been damaged by an accident or unreasonable use, neglect,
improper service, or other causes not arising from defects in materials or construction. This warranty
does not cover the elimination of externally generated static or noise, or the correction of antenna
problems or weak reception, damage to speakers, accessories, electrical systems, cosmetic damage
or damage due to negligence, misuse, failure to follow operating instructions, accidental spills or
customer applied cleaners, wear due to environmental causes such as floods, airborne fallout,
chemicals, salt, hail, lightning or extreme temperatures, damage due to accidents, road hazards, fire,
theft, loss or vandalism, damage due to improper connection to equipment of another manufacturer,
modification of existing equipment, or Product which has been opened or tampered for any reason.
Units that are damaged by abuse resulting in thermally damaged voice coils are not covered by this
warranty but may be replaced at the absolute and sole discretion of Soundstream Technologies. The
unit must be returned to Soundstream Technologies, postage pre-paid, with bill of sale or other dated
proof of purchase bearing the following information: consumer’s name, telephone number, address,
authorized dealer’s name, address, and product description. Please contact the Soundstream
Technologies warranty office at 800.832.4647 or [email protected] to obtain a Return
Authorization number before shipping the product.
Note: This warranty does not cover labor costs for the removal and re-installation of the unit. FOR
THE TWO-YEAR WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF
INSTALLATION BY A SOUNDSTREAM TECHNOLOGIES AUTHORIZED DEALER. ALL UNITS
RECEIVED BY SOUNDSTREAM TECHNOLOGIES FOR WARRANTY REPAIR WITHOUT PROOF
OF SOUNDSTREAM TECHNOLOGIES AUTHORIZED DEALER INSTALLATION AND PURCHASE
WILL BE COVERED BY THE LIMITED 1 YEAR WARRANTY.
BY PURCHASING THIS PRODUCT, ALL WARRANTIES INCLUDING BUT NOT LIMITED TO
EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS
FOR PARTICULAR PURPOSE, AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL
PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW, AND
SOUNDSTREAM TECHNOLOGIES NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO
ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT.
SOUNDSTREAM TECHNOLOGIES HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS
OF THIRD PARTIES, INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. BY
PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL
DISPUTES BETWEEN THE CONSUMER AND SOUNDSTREAM TECHNOLOGIES SHALL BE
RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN LOS ANGELES COUNTY,
CALIFORNIA. Some states do not allow limitations on how long an implied warranty lasts. In such
states, the limitation or exclusions of this Limited Warranty may not apply. Some states do not allow
the exclusion or limitation of incidental or consequential damages. In such states, the exclusion or
limitation of this Limited Warranty may not apply to you. This Limited Warranty gives you specific legal
rights, and you may have other rights which vary from state to state.