Soundstream RESERVE User manual

RESERVE
by
OEM UPGRADE HEAD UNIT FOR
‘98-’13 HARLEY-DAVIDSON®ELECTRA GLIDE®,
ULTRA®, & STREET GLIDE® MOTORCYCLES
INSTALLATION GUIDE
To print a complete owners manual, visit us
online at motorcycleaudio.com/hdhu9813SG
- or -
scan this QR code with your phone’s
camera to download the complete
owners manual to your phone.

Removal of the Fairing & Original Head Unit
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main
fuse before proceeding.
1. Remove four fairing screws holding the outer fairing to the
inner fairing using a T27 Torx driver. The rst two screws are
located under the fairing adjacent to each fork:
Tip: Turn the handlebar for better access to
the screws.
The second pair of screws are below/adjacent
to each speaker:
2. Remove three screws that attach the windshield &
outer fairing to the inner fairing using a T27 Torx driver.
Remove the windshield & set aside. Reinstall the center
screw by hand to hold the outer fairing in place. Set
remaining screws aside for installation later.
3. While straddling the front wheel fender, grasp the outer fairing.
Remove the center windshield screw. Gently pull the fairing apart
from the bike. With the fairing slightly pulled away from the bike,
disconnect wire harness for the headlight or any other accessories.
Lay the fairing on a protected at surface to prevent damage.
4. Disconnect all wire harnesses from the OEM radio. Use a
pry tool, at-head screwdriver, or pick tool to lift up on the
locking tab, then pull the male connector(s) out from the female
connector(s). Also, unplug the FM antenna & disconnect the CB
antenna (if equipped). If the OEM SiriusXM tuner is installed,
disconnect & remove its antenna, it will not be used.

Removal of the Fairing & Original Head Unit(cont.)
5. Remove the OEM head unit by
removing 4 screws from the head
unit support bracket. Use a 3/16”
hex/allen key tool to remove 2
screws from each side. An access
hole in the fairing support brackets
accommodates a hex/allen tool.
Set these four screws aside for
reinstallation.
6. Gently pull the OEM radio out and up, away from the support
bracket. No other parts from the OEM radio are needed.
7. Take a moment to clean the surfaces of the inner fairing surrounding
the cutout for the radio & around the rectangle recess using a damp
micro-ber cloth. Any debris or residue left on these surfaces can
affect the water-tight seal around HDHU.9813SG.
Installation of HDHU.9813SG Head Unit
1. The ignition switch needs to be removed for initial installation. Turn the
handlebars to the far left, then turn the ignition switch counterclockwise
to FORK LOCK.
2. Insert the key & press the unlock pin under the switch, on the left
side. While pressing the unlock pin under the switch, turn the key
counterclockwise slightly beyond the UNLOCK position.
3.The ignition switch should be free.
Remove the ignition switch with spring and set aside.
4. Route the USB cable, antenna extension, & RCA camera input
w/ trigger into the cutout of the inner faring. Pull the chassis of
HDHU.9813SG thru the rectangular recess, aligning the mounting
screw holes with the holes of the fairing support bracket.
5. Secure HDHU.9813SG to the radio
support bracket with the 4 screws set
aside during removal of the original head
unit (step 5) using the same hex/allen key
tool.

Installation of HDHU.9813SG Head Unit(cont.)
6. Insert and lock the male OEM head unit wire harness
connector(s) to the female socket(s) of the included wire
harness. Then, insert and lock the male connector of the
included wire harness into the corresponding female socket
on the back of HDHU.9813SG. Swivel the latch into place,
locking the male connector into the female receptacle.
7. Identify the location you wish to have the CarPlay/Android Auto
USB connector. Drill a hole at the location using a 13/16” or 7/8”
spade bit or step bit. Route the USB cable from the head unit to the
USB location.
8. Remove the USB port cap, unthread the plastic nut and remove the gasket
for the USB port cap. Be sure the secondary gasket ring remains. Insert the
threaded end of the USB port thru the hole drilled during the previous step.
Slip the gasket ring of the USB port cap over the threaded USB port. Thread
the plastic nut down the USB port to secure it to the fairing surface. Finally,
reattach the USB port cap.
9. Connect the FM radio antenna to the female receptacle extension, and any accessory added to this
installation; SiriusXM tuner, Bluetooth calling microphone, camera video-in & trigger, amplier audio
RCA’s etc. The wire harness of HDHU.9813SG also includes a blue remote turn-on wire for amplier(s).
10. Disconnect the indicator lamp
wire harness, located between
the speedometer and tachometer.
Connect the female OEM connector
to the corresponding male connector
of HDHU.9813SG. Tuck away the
unused portion of the OEM indicator
lamp cable and excess cable.
3. 5mm Connection for Included
Bluetooth Calling Microphone
Camera Video-in
Camera Turn-on (12V, 1A)
USB
Indicator Light Connector
Radio Antenna

Installation of HDHU.9813SG Head Unit(cont.)
11. Reinstall the ignition switch pointing towards FORK LOCK with
the key inserted and turned to the position beyond UNLOCK. Turn
the key back to the UNLOCK position. a click sound should be heard,
conrming the ignition switch has been installed correctly. If the switch
is loose and comes out, repeat this step.
12. Take a moment to reinstall the main fuse if it was removed. At this point, HDHU.9813SG should turn-
on when the ignition switch is in the IGNITION position. Verify all speakers are playing and the head
unit is functioning. If successful, tie any loosely hanging cable/wires that might impede reinstallation
of the fairing.
Reinstallation of the Fairing
1. While straddling the front wheel fender and holding the
outer fairing, reconnect the wire harness for the headlight
or any other accessories. Hold the outer fairing against
the inner fairing and loosely thread the three windshield
screws hand tight using a T27 Torx driver.
2. Tuck away any loosely hanging cables/wires and loosely
secure the 4 inner fairing screws using a Torx T27 driver. The rst
two screws are located under the fairing adjacent to each fork:
Tip: Turn the handlebar for better access to
the screws.
The second pair of screws are below/adjacent
to each speaker:
3. Remove the three windshield screws and insert the windshield into place between the inner and
outer fairing. Thread the windshield screws thru the outer fairing & windshield into the inner fairing.
4. Finally, tighten all the screws into place.