Southern Enterprises HZ3480R0TX User manual

HZ3480R0TX
Wall-Mount Ironing Center
Assembly Instruction
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
© Southern Enterprises Inc. All Right Reserved
.
PO:
Max load on ironing board 40lb

Tool List: 3/16" Drill Bit, Drill, Tape Measure and Pencil .
HZ3480R0TX
Wall-Mount Ironing Center
Parts List
Please review all parts and hardware before disposing of any packaging.
Before beginning assembly, separate each type of hardware. Carefully study the
diagrams below and check that you have all parts indicated. Call Customer Service if missing
hardware. Using the incorrect hardware will cause damage.
Suggested T
ools: Phillip head screw driver, power drill,
3/16
” drill bit,
24” level, and a tape measure. Unit needs to be hung on wall stud for
more security and stability.
(1) Cabinet
1 PC
(2) Plastic Wall Anchor
3 PCS
1 extra included
(3) Washer
3 PCS
3/16″x1/2”
(4) Screw 3PCS
￠4mm ×2”
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish on wood part. Avoid rubbing or
scratching the surface with rough or abrasive
objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Assembly Tool Required
No.2 Phillips Screwdriver

Floor
HZ3480R0TX
Wall-Mount Ironing Center
Assembly Instructions
1 screw MUST BE directly
mounted into a wall stud. Wall
anchor is not needed when
mounting into a wall stud.
Step1: Measure the wall and
mark the location of the center of
each mounting holes. See
Figure 2.
NOTICE
If your wall studs are 12”
apart, please make sure the
top 2 holes are located on wall
stud. However, at least one
top hole must located on a
wall stud.
Using the level, make sure that
all marks are level on the wall.
Step 2: Using power drill and
3/16″drill bit, drill two 3/16″holes
through the wallboard at the
mounting hole marks.
Notice: Only drill a 3/16” hole
for the holes that are going to
need a wall anchor. Screws
for wall stud should be
directly screwed into the wall
and into the stud.
Figure 1-Screw Hole Location
Drill
three
3
/
16
"
holes
into wall

Step 3: Insert Plastic Anchors
(2) into the mounting holes.
(When doing this, you will need
a hammer help you).
Step 4: Open Cabinet (1) and
attach Cabinet (1) to the wall
using Washers (3) and Screws
(4) as shown.
Figure 2
Customer Service 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway,Suite 200
Coppell,Texas 75019
2
3
3
4

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
lease contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at servi[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019