Southern Enterprises HZ104700TX User manual

Page | 1
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]m
www.seidal.com
HZ104700TX
Marc Bar Cabinet
Assembly Instructions
PO#:

Page | 2
Marc Bar Cabinet
Assembly Instructions
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Left Side Panel
D.
Quantity
of 1
Right Side Panel
E.
Quantity
of 1
Upper Fixed Shelf Panel
F.
Quantity
of 1
Lower Fixed Shelf Panel
G.
Quantity
of 1
Left Vertical Panel
H.
Quantity
of 1
Right Vertical Panel
I.
Quantity
of 2
Middle Vertical Panel
J.
Quantity
of 2
Small Fixed Shelf Panel
K.
Quantity
of 1
Left Door
L.
Quantity
of 1
Right Door

Page | 3
M.
Quantity
of 1
Upper Back Panel
N.
Quantity
of 1
Middle Back Panel
O.
Quantity
of 1
Lower Back Panel
1.
Quantit
y
of 40
Cam Bolt
2.
Quantity
of 40
Cam Lock
3.
Quantity
of 40
Wood Dowel Ø 8 x 30mm
4.
Quantity
of 28
Flat Head Screw
∅
1/8"x1/2"
5.
Quantity
of 4
Bolt for Handle
∅
5/32"x3/4"
6.
Quantity
of 34
Round Head Screw
Ø 1/8” x 5/8”L
(for Back Panel and Magnet)
7.
Quantity
of 4
M
agnet
8.
Quantity
of 2
Handle
9.
Quantity
of 4
Hinge
10.
Quantity
of 4
Magnet Plate
11.
Quantity
of 6
Metal Plate
12.
Quantity
of 4
Bracket

Page | 4
13.
Quantity
of 4
Screw
∅
1/8"x5/8"
14.
Quantity
of 4
Screw
Ø 1/8” x 1-5/8”L
15.
Quantity
of 4
Anchor
16.
Quantity
of 2
Plastic Strap
17.
Quantity
of 24
Cover
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required No.2 Phillips
Screwdriver (Not Included)

Page | 5
Figure 1
Screw with fingers to help align cam
bolts before using screwdriver.
Insert Cam Locks (2) into corresponding
holes on Small Fixed Shelf Panel (J).
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Left Vertical Panel (G).
Attach Small Fixed Shelf Panel (J) to
Left Vertical Panel (G) by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until Small Fixed
Shelf Panel (J) and Left Vertical Panel
(G) meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 2
Insert Cam Locks (2) into corresponding
holes on Small Fixed Shelf Panel (J).
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Right Vertical Panel (H).
Attach Small Fixed Shelf Panel (J) to
Right Vertical Panel (H) by inserting
Wood Dowels (3) and Cam Bolts (1) into
corresponding holes until Small Fixed
Shelf Panel (J) and Right Vertical Panel
(H) meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Notice: Make sure that all finished
edges are facing towards the front of
the unit.
Marc Bar Cabinet
Assembly Instructions
J
2
2
3
3G
2
2
3
3
H
J

Page | 6
Figure 3
Insert Cam Locks (2) into corresponding
holes on assembled unit from Figure 1
and Figure 2.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Upper Fixed Shelf Panel (E) and Under
Fixed Shelf Panel (F)
Attach Upper Fixed Shelf Panel (E) and
Lower Fixed Shelf Panel (F) to
assembled unit by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until Upper Fixed
Shelf Panel (E) and Lower Fixed Shelf
Panel (F) and assembled unit meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure
4
Insert Cam Locks (2) into corresponding
holes on Middle Vertical Panels (I).
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Upper Fixed Shelf Panel (E) and Lower
Fixed Shelf Panel (F)
Attach Middle Vertical Panels (I) to
Upper Fixed Shelf Panel (E) and Lower
Fixed Shelf Panel (F) by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until all panels
meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
1
2
2
2
E
F
J
H
J
2
2
1
1
3
3
I
I
E
F

Page | 7
Figure
5
Insert Cam Locks (2) into corresponding
holes on assembled unit.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Left Side Panel (C) and Right Side
Panel (D)
Attach Left Side Panel (C) and Right
Side Panel (D) to assembled unit by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes until
Left Side Panel (C), Right Side Panel
(D) and assembled unit meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Attach Magnets (7) to Top Panel (A)
using Round Head Screw (6) as shown.
Tighten Round Head Screw (6) with
Phillips screwdriver.
C2
2
D
A

Page | 8
Figure
7
Attach Magnets (7) to Bottom Panel (B)
using Round Head Screw (6) as shown.
Tighten Round Head Screw (6) with
Phillips screwdriver.
Figure 8
Insert Cam Locks (2) into corresponding
holes on the top and bottom of the
assembled unit.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Top Panel (A) and Bottom Panel (B)
Attach Top Panel (A) and Bottom Panel
(B) to assembled unit by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until Top Panel (A)
and Bottom Panel (B) and assembled
unit meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
3
D

Page | 9
Figure
9
Attach Back Panels (M/N/O) to backside
of the unit with Round Head Screws (6)
and Metal Plates (11).
Tighten Screws (6) with a Phillips
screwdriver.
Figure
1
0
Attach the Metal Plate (10) to the inside
of the Left Door (K) using Flat Head
Screws (4).
Attach the Hinges (9) on the Left Door
(K) using Flat Head Screws (4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Attach Handle (8) to the door using Bolts
for Handle (5).
Tighten Bolts (5) with Phillips
screwdriver.
11
11
11
11
11
11
N
9
9
4
5
5
8
10
10
K

Page | 10
Figure 11
Attach the Metal Plate (10) to the inside
of the Right Door (L) using Flat Head
Screws (4).
Attach the Hinges (9) on the Right Door
(L) using Flat Head Screws (4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Attach Handle (8) to the door using Bolts
for Handle (5).
Tighten Bolts (5) with Phillips
screwdriver.
Figure 1
2
Attach the door to the unit using Flat
Head Screws (4)
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Cover Cam Locks with Covers (17) as
shown.
8
9
9
10
10
L
4
4
17
to achieve uniform
clearance around the door,
you may need to adjust
the door by tightening or
loosening the two screw
on the hinge itself.
screws for adjusting
the door

Page | 11
Figure 1
3
Attach Brackets (12) to back panel using
Screws (13).
Tighten Screws (13) using Philips
screwdriver.
Mark two desired locations on wall in the
same distance as the brackets on the
back of the unit and drill two 3/16" holes
for each Bracket (12).
Insert Plastic Anchors (15) into the holes
for each Bracket (12) on wall as shown.
Use a hammer to insert plastic anchors
until they are flush with wall.
Then, attach Brackets (12) onto wall
using Screws (14).
Tighten Screws (14) using Philips
screwdriver.
Figure 19
Move the unit close to the wall Brackets
(12) and tie in all Brackets (12) together
with Plastic Straps (16) as shown in
diagram.
Anti-tipping hardware must be used
for this product to avoid tipping and
injury.
13
12
13
12

Page | 12
Figure 20
Now your Marc Bar Cabinet is ready for
use.

Page | 13
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas)
Mon-Fri 9am – 4pm CST, or email us at [email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019