Southern Enterprises ARGO 349500TX User manual

1
HZ349500TX ARGO WALL MOUNT
SHELF W/HOOKS-GRAYED OAK
HZ349600TX ARGO WALL MOUNT
SHELF W/HOOKS-LIGHT OAK
Asse bly Instructions
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[e-mail]
www.seidal.com
PO#

2
Tool List: 3/16" drill bit, drill, tape measure and pencil
WALL MOUNT SHELF W/HOOK
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A Quantity
Of 2
plastic anchor
Dia: 1/4” x 1-3/16”L
B Quantity
Of 2
screw
Dia: 1/4“ x 1-1/2”L
C Quantity
Of 1
shelf
D
Quantity
of 1
leveler
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required
No.2 Phillips Screwdriver
Not Included

3
NOTE: NO DRILLED HOLE OR PLASTIC ANCHOR
REQUIRED WHEN MOUNTING TO WOOD WALL.USE
SCREW ONLY. WE DO NOT SUPPLY HARDWARE FOR
MOUNTING ON CONCRETE WALLS.
Figure 1
Find a desired location and mark two locations
for the screws.
One screw (for each unit) must be attached
directly into a wall stud. Wall anchor is not
needed when mounting to wall stud.
Drill one marking 3/16" hole (for each unit).
Insert plastic anchor (A) into the hole on wall as
shown, you will need a hammer when doing this.
Using the phillips head screwdriver, install one
screw (B) into the anchor (A) and the other
screw installed into the stud. Turn the screws
(B) until there is a gap of approximately 13 mm
between the head of the screw and the wall as
shown.
Figure 2
Hang shelf (C) onto the screws and verify the
shelf (C) is resting securely on the mounting
screws (B).
Use a leveler to insure product is level.
Now your wall mount shelf w/hook is ready to
use.
Wall Mount Shelf W/Hook
Assembly Instructions
"The holes measurement on
wall must match with the
holes measurement on back
of the unit"

4
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at servi[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity
Needed
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Parts Replacement Form

5
CAUTION
Max shelf load capacity is achieved by mounting screw into studs or cement walls.
Shelf support up to 8lbs
Per hook support up to 1lbs
If mounting to sheet rock (cavity wall) it is advisable to mount at least one screw
(without anchor) directly to a wall stud or studs. However do not leave either end of mounting
bracket unsupported by at least one anchor. For hollow wall mounting you can use any of the
holes in the back plate to suit where you require the mounting screws positioned.