Southern Enterprises MS871300TX User manual

PO#:
Page 1
MS871300TX
Casselton TV/Media
Stand - Burnt Oak
Assembly Instructions

1 Quantity
of 1
Top Panel
2 Quantity
of 1
Left Side Panel
3 Quantity
of 1
Right Side Panel
4 Quantity
of 1
Shelf Panel
5 Quantity
of 1
Upper Middle Panel
6 Quantity
of 1
Lower Middle Panel
7 Quantity
of 1
Cross Panel
8 Quantity
of 1
Back Cross Panel
9 Quantity
of 1
Lower Cross Panel
10 Quantity
of 1
Bottom Panel
11 Quantity
of 1
Back Panel
12 Quantity
of 4
Drawer Front
Page 2
Casselton TV/Media Stand - Burnt Oak
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.

13 Quantity
of 4
Left Drawer Side Panel
14 Quantity
of 4
Right Drawer Side Panel
15 Quantity
of 4
Drawer Back Panel
16 Quantity
of 4
Drawer Bottom Panel
A Quantity
of 16
Cam Bolt
B Quantity
of 16
Cam Lock
C Quantity
of 22
Wood Dowel
Dia. 5/16” x1-1/4”
D Quantity
o f 8
Bolt Dia. 1/4x1-1/4” L
E Quantity
o f 4
Spring Washer Dia. 1/4”
F Quantity
o f 4
Flat washer Dia. 1/4”x3/4”
G Quantity
o f 1
Allen Wrench
H Quantity
o f 36
Screw Dia. 5/32” x 1L
I Quantity
of 25
Screw Dia. 1/8” x 1/2”L
Page 3

J Quantity
o f 4
Handle
K Quantity
o f 8
Bolts Dia. 5/32” x 3/4”L
L Quantity
of 2
Anti-tipping hardware
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Page 4
Assembly Tool Required
No.2 Phillips Screwdriver
(Not Included)

Page 5
Figure 1
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on Middle Panels (5/6).
Screw Cam Bolts (A) into threaded holes
on Shelf Panel (4) and Cross Panels
(7/8).
Attach Shelf Panel (4) and Cross Panels
(7/8) to Middle Panels (5/6) by inserting
Cam Bolts (A) and Wood Dowels (C) into
corresponding holes until all components
meet.
Tighten by rotating Cam Locks (B)
clockwise using Phillips screwdriver.
Figure 2
Insert Cam Locks (B) into corresponding
holes on assembled unit from Figure 1.
Screw Cam Bolts (A) into threaded holes
on Left Side Panel (2) and Right Side
Panel (3).
Attach Left Side Panel (2) and Right Side
Panel (3) to the assembled unit from
Figure 1 and Lower Across Panel (9) by
inserting Cam Bolts (A) and Wood
Dowels (C) into corresponding holes
until all components meet.
Tighten by rotating Cam Locks (B)
clockwise using Phillips screwdriver.
Use Bolts (D), Flat Washers (E), and
Spring Washers (F) to connect Side
Panels (2/3) to assembled unit from
Figure 1.
Tighten Bolts (D) using Allen Wrench
(G).
Casselton TV/Media Stand- Burnt Oak
Assembly Instructions

Page 6
Figure 3
Insert Cam Locks (B) into holes on the
assembled unit from Figure 2.
Screw Cam Bolts (A) into threaded holes
on Bottom Panel (10).
Attach the assembled unit from Figure 2
to Bottom Panel (10) by inserting Cam
Bolts (A) and Wood Dowels (C) into
corresponding holes until Bottom Panel
(10) and assembled unit from Figure 2
meet.
Tighten by rotating Cam Locks (B)
clockwise with Phillips screwdriver.
Figure 4
Attach Top Panel (I) to Side Panels (2/3)
with Bolts (D) and Wood Dowels (C).
Tighten with Allen Wrench (G) as shown.

Page 7
Figure 5
Attach the Back Panel (11) to the
assembled unit with Screws (I).
Tighten Screws (I) with Phillips
screwdriver.
Figure 6
Attach Drawer Side Panels (13/14) to
Drawer Back Panel (15) using Screws
(H).
Tighten Screws (H) with Phillips
screwdriver.
Insert Drawer Bottom Panel (16) into the
grooves of panels (13/14) and (15).
Attach Drawer Front Panel (12) to the
assembled unit using Screws (H).
Finally, attach Handle (J) to the Drawer
Front Panel (12) using Bolts (K).
Tighten Bolts (K) with Phillips
screwdriver.

Figure7
Insert drawers into assembled unit as
shown.
Make sure all slides glide smoothly in and
out.
Note: There is a lever located on the
male slide for bottom drawer slide.
Push the lever to the either side in
order to detach the male slide from the
female slide.
Figure 8
Attach Brackets (L) to Back Panel using
short Screws (L). Tighten Screws (L)
using a Philips screwdriver.
Mark two desired locations on wall. Drill
two 3/16" holes for each Bracket (L) on
wall. Insert Plastic Anchors (L) into the 2
holes on wall as shown. (When doing
this, you will need a hammer help you).
Then attach Brackets (L) to wall using
long Screws (L). Tighten Screws (L)
using a Philips screwdriver.
Move this item close to the wall Brackets
(L) and tie in both Brackets (L) with
Plastic Straps (L) as shown in diagram.
Anti-tipping hardware must be used
for this product to avoid tipping and
injury.

Page 8
Figure 9
Now your Casselton TV/media stand is
ready to use.

Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90
days of your receipt of the product. Replacement, if available, will be honored within this time frame.Parts will not be available for items
arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product
modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or
replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas) Mon-Fri 9am – 4pm CST, or
email us at [email protected]. Please ask for customer service representative for issues involving damages or replacement parts.
Please ask for technical assistance representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Page 9
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019