Southern Enterprises HZ106300TX User manual

HZ106300TX
Hagan Storage Cabinet
Assembly Instructions
PO:13411
For assistance with assembly, contact.
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
Top supports up to 40 lb.
Per adjustable shelf supports up to 20 lb.
Fixed bottom shelf supports up to 30 lb.

HZ106300TX
HAGAN STORAGE CABINET
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware.
Carefully study the diagrams below.
You may receive extra hardware with your unit.
1 1PC
Top Panel
2 1PC
Left Panel
3 1PC
Right Panel
4 1PC
Back Panel
5 1PC
Bottom Panel
6 2PCS
Shelf
7 1PC
Left Door
8 1PC
Right Door
9 1PC
Upper Leg
10 1PC
Lower Leg

A 1PC
Magnet
B 4PCS
Screw 3x15mm
C 8PCS
Wood Dowel
D 6PCS
Cam Bolt
E 6PCS
Cam Lock
F 10PCS
Screw 8x1-1/2”L
G 1PC
Bolt 3/16”x1/2”L
H 4PCS
End Cap
I 2PCS
Iron Chip
J 2PCS
Screw 3x8mm
K 4PCS
Door Hinge
L 16PCS
Screw 6x1/2”L
M 8PCS
Bracket
N 4PCS
L Metal Chip
O 2PCS
Screw 4x12mm
P 2PCS
Wall Anchor
Q 2PCS
Screw 4x1”L
R 2PCS
Plastic Strap
Assembly Tool Required
No.2 Phillips Screwdriver
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the surface with
rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096.

HZ106300TX
HAGAN STORAGE CABINET
Assembly Instructions
Figure 1
Step 1 :
Unit assembly should begin
with parts turned upside down
for Step 1.
Attach magnet (A) into the
pre-drilled holes on Top Panel
(1) using Screws (B) as
shown.
Attach Left Panel (2) and
Right Panel (3) to Top Panel
(1) using Wood Dowels (C)
and Cam Bolts (D) as shown.
Figure 2
Step 2 :
Fix Left Panel (2) and Right
Panel (3) to Top Panel (1)
using Cam Locks (E) as
shown.

Figure 3
Step 3:
Slide Back Panel (4) along the
grooves of Left Panel (2) and
Right Panel (3).
Then, attach Wood Dowels (C)
to Left Panel (2) and Right
Panel (3) as shown.
Figure 4
Step 4:
Attach Bottom Panel (5) to the
assembled unit using Screws
(F) as shown.

Figure 5
Step 5:
Attach Lower Leg (10) to Upper
Leg (9) using Bolt (G). Then,
aim at the pre-drilled holes on
the Bottom Panel (5) to attach
the assembled Leg Frame to
Bottom Panel (5) using Screws
(F) as shown.
Attach End Caps (H) to Legs
(9) and (10) as shown.
Figure 6
Step 6:
Attach Door Hinges (K) to Left
Door (7) and Right Door (8)
using Screws (L). Then, attach
Iron Chip (I) using Screws (J)
as shown.
Please make sure the side
of the Iron Chips (I) with tips
are facing in towards the
Doors (7/8) while attaching.
L
JI
K
8
K
7
7,
8
I
J

Figure 7
Step 7:
Turn the assembled unit
upright.
Attach Doors (7) and (8)
w/Door Hinges (K) to the
grooves of Left Panel (2) and
Right Panel (3) using Screws
(L) as shown.
Figure 8
Step 8:
Insert Brackets (M) into the
holes on the insides of Left
Panel (2) and Right Panel (3)
and make sure the positions
of the Brackets (M) are even.
Insert Shelves (5) following the
arrow direction and make sure
Brackets (M) hold Shelves (5)
stably.
Your storage cabinet is now
complete.
8
7
L
K
3
2

Anti-tipping
Hardware Must be
Used for this
product to avoid
tipping and injury
Aim at the pre-drilled holes on
the back of Left Panel (2) and
Right Panel (3) to attach L
Metal Chip (N) using Screws
(O) as shown.
Tip: Screw must be directly
mounted into a wall stud. Wall
anchor is not needed when
mounting into a wall stud.
Find an ideal location on the
wall and mark the location of
the center of each mounting
hole.
Using a power drill and a
3/16″drill bit, drill two 3/16″
holes on the wall.
Note: Make sure not to drill into
electrical wiring or plumbing
pipes.
Insert Wall Anchors (P) into the
two 3/16″holes. Make sure that
the wall anchors are flush with
the wall.
Tip: It may be necessary to use
a hammer to gently tap the
anchors into place.
FLOOR
31.25
”
27.
5
”

Attach L Metal Chip (N) to Wall
Anchor (P) u sing Phillips Head
Screws (Q) and the Phillips
Screwdriver as shown.
Attach Plastic Strap (R) to L
Metal Chip (N) on the wall and
cabinet as shown.
(Q)

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at [e-mail]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalo
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Parts Replacement Form