Southern Enterprises HZ1032A0TX User manual

For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]om
www.seidal.com
1
HZ1032A0TX/ HZ1032B0TX
Shadowbox Wine/Bar
Cabinet
Assembly Instructions
Due to weight, assembly requires two people.
Following detailed instructions, assembly should take approximately two hours.

PACKAGE CONTENTS
2
A
W
V
M
S
T
S
S
T
T
S
O
D
O
L
N
P
J
G
U
U
F
C
J
J
K
E
Y
I
B
R
Z
Z
R
H
J
Q
Q
X
G
U

HARDWARE CONTENTS
PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY
A Top Panel 1 N Shelf 1
B Bottom Panel 1 O Vertical Panel 2
C Left Side Panel 1 P Vertical Panel 1
D Right Side Panel 1 Q Wine Rack Panel 4
E Shelf 1 R Leg 2
F Shelf 1 S Glass Rack Side 4
G Vertical Panel 2 T Glass Rack Middle 4
H Vertical Panel 1 U Wine Shelf 6
I Shelf 1 V Back Panel 1
J Vertical Panel 4 W Back Panel 1
K Shelf 1 X Left Door 1
L Shelf 1 Y Right Door 1
M Shelf 1 Z Metal Rail 4
3
1
Wood dowel
Qty:
92
2
Cam bolt
Qty:
68
3
Cam lock
Qty:
68
4
Hinge
Qty:
6
5
Screw 1/2” L
Qty: 42
6
Screw 1/2” L
Qty:
48
7
Magnet
Qty:
6
8
Screw 1-1/4” L
Qty:
24
9
Screw 1-3/8” L
Qty:
4
Bracket
Qty:
4
Plastic strap
Qty:
2
Anchor
Qty:
4
10 11 12

4
Screw 5/8” L
Qt
y:
4
Bolt 1/2”L
Qty:
14
Allen wrench
Qty:
1
Paper cover
Qty:
68
14 15 16
13

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x 8
HARDWARE USED
Wood Dowel x 4
Cam Bolt x 4
Cam Lock x 4
Paper Cover x 4
5
Wood may scratch easily, please
Be careful when assembling. Do not
scratch.
1. Attach shelf (M), vertical panels (O) and
shelf (N) by inserting wood dowels (1)
into holes.
2. Insert cam locks (3) into holes in
assembled unit on Figure 1.
Screw cam bolts (2) into holes on
vertical panel (P).
Attach vertical panel (P) to assembled
unit on Figure 1 by inserting wood
dowels (1) and cam bolts (2) into
corresponding holes until vertical panel
(P) and assembled unit on Figure 1
meet.
Tighten by rotating cam locks (3) in
clockwise direction with Phillips
screwdriver.
Cover cam lock holes with paper covers
(16).
1
2
1
1
2
3
16
M
N
O
O
1
1
2
3
16
P
N

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x 4
Cam Bolt x 4
Cam Lock x 4
Paper Cover x 4
HARDWARE USED
Screw 1/2” x 4
Magnet x 2
6
3. Insert cam locks (3) into corresponding
holes in assembled unit on Figure 2.
Screw cam bolts (2) into corresponding
holes on shelf (L). Attach shelf (L) to
assembled unit on Figure 2 by inserting
wood dowels (1) and cam bolts (2) into
corresponding holes until shelf panel (L)
and assembled unit meet.
Tighten by rotating cam locks (3) in
clockwise direction with Phillips
screwdriver.
Cover cam lock holes with paper covers
(16).
Make sure cam lock holes on shelf (L)
are facing down as shown on illustration.
4. Attach magnets (7) to shelf (K) using
screws (6).
Tighten screws with Phillips screwdriver.
3
4
6
7
1
2
3
16
1
2
3
16
L
J
N
7
6
K

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x 8
Cam Bolt x 8
Cam Lock x 8
Paper Cover x 8
HARDWARE USED
Wood Dowel x 8
Cam Bolt x 8
Cam Lock x 8
Paper Cover x 8
7
5. Insert cam locks (3) into corresponding
holes on vertical panels (J). Screw cam
bolts (2) into corresponding holes on
assembled unit on Figure 3.
Attach assembled unit to vertical panels
(J) by inserting wood dowels (1) and
cam bolts (2) into corresponding holes
until vertical panel (J) and assembled
unit meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper covers
(16).
Repeat these steps to attach shelf (K) to
assembled parts.
6. Insert cam locks (3) into holes on vertical
panels (G). Screw cam bolts (2) into
holes on shelf (F).
Attach shelf (F) to vertical panels (G) by
inserting wood dowels (1) and cam bolts
(2) into corresponding holes until they
meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper covers
(16).
Repeat steps to attach shelf (E) to
vertical panel
s (G).
5
6
1
2
3
16
1
2
3
16 K
J
J
1
2
3
16
F
1
2
G
G
E
3
16
16

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x 4
Cam Bolt x 4
Cam Lock x 4
Paper Cover x 4
HARDWARE USED
Wood Dowel x 2
Cam Bolt x 2
Cam Lock x 2
Paper Cover x 2
8
7. Insert cam locks (3) into holes in
assembled parts from Figure 6.
Screw cam bolts (2) into holes on vertical
panel (H).
Attach vertical panel (H) to assembled
unit on Figure 6 by inserting wood dowels
(1) and cam bolts (2) into corresponding
holes until vertical panel (H) and
assembled unit meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper covers
(16).
8. Insert cam locks (3) into holes on shelf
(I).
Screw cam bolts (2) into holes on
assembled unit on Figure 7.
Attach shelf (I) to assembled unit on
Figure 7 by inserting wood dowels (1)
and cam bolts (2) into corresponding
holes until they meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper covers
(16).
7
8
1
2
3
16
1
2
3
16
1
3
2
H16
1
2
3
I
16

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x 2
Cam Bolt x 2
Cam Lock x 2
Paper Cover x 2
HARDWARE USED
Screw 1/2” x 4
Magnet x 2
9
9. Insert cam locks (3) into holes on
vertical panel (J).
Screw cam bolts (2) into holes on
assembled unit on Figure 8.
Attach vertical panel (J) to assembled
unit on Figure 8 by inserting wood
dowels (1) and cam bolts (2) into
corresponding holes until vertical panel
(J) and assembled unit meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper covers
(16).
10. Attach magnets (7) to bottom panel (B)
with screws (6).
Tighten screws with Phillips
screwdriver.
9
10
1
2
3
16
1
2
J
3
16
6
7
6
7
B

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x 2
Cam Bolt x 2
Cam Lock x 2
Paper Cover x 2
HARDWARE USED
Wood Dowel x 4
Cam Bolt x 4
Cam Lock x 4
Paper Cover x 4
10
11. Insert cam locks (3) into holes on
assembled unit on Figure 9.
Screw cam bolts (2) into holes on
bottom panel (B).
Attach bottom panel (B) to assembled
unit on Figure 9 by inserting wood
dowels (1) and cam bolts (2) into
corresponding holes until bottom (B)
and assembled unit meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper
covers (16).
12. Insert cam locks (3) into holes in
assembled unit on Figure 11.
Screw cam bolts (2) into holes on
assembled unit on Figure 5.
Attach assembled parts from Figure 5 to
assembled unit on Figure 11 by
inserting wood dowels (1) and cam bolts
(2) into corresponding holes until units
meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper covers
(16).
11
12
1
2
3
16
1
2
3
16
1
B
3
2
16
2
3
1
K
B
16

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Hinge x 3
Screw 1/2” L x 12
HARDWARE USED
Hinge x 3
Screw 1/2” L x 12
11
13. Attach hinges (4) to left side of panel
(C) with screws (5).
Note: Do not tighten the screws until
step 24 is complete.
14. Attach hinges (4) to right side of panel
(D) with screws (5).
Note: Do not tighten the screws until
step 24 is complete.
14
4
5
4
5
C
4
5
13
4
5
D

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x22
Cam Bolt x22
Cam Lock x22
Paper Cover x22
HARDWARE USED
Screw 1/2” x 4
Magnet x 2
12
15. Insert cam locks (3) into holes on
assembled parts from Figure 12.
Screw cam bolts (2) into holes on left
side panel (C).
Attach left side panel (C) to assembled
unit on Figure 12 by inserting wood
dowels (1) and cam bolts (2) into
corresponding holes.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Repeat steps to attach right side panel
(D). Cover cam lock holes with paper
covers (16).
This step may take two people to
complete.
Work panels (C) and (D) from bottom to
top assuring that all cam bolts and
wood dowels are inserted through their
corresponding holes.
16. Attach magnets (7) to top panel (A) with
screws (6).
Tighten screws with Phillips
screwdriver.
16
1
2
3
16
15
1
2
C
D
B
16
6
7
A
7
6

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Wood Dowel x 8
Cam Bolt x 8
Cam Lock x 8
Paper Cover x 8
HARDWARE USED
13
17. Insert cam locks (3) into holes
assembled unit on Figure 15.
Screw cam bolts (2) into holes on top
panel (A).
Attach top panel (A) to assembled unit
on Figure 15 by inserting wood dowels
(1) and cam bolts (2) into
corresponding holes until assembled
unit meet.
Tighten by rotating cam locks (3)
clockwise with Phillips screwdriver.
Cover cam lock holes with paper
covers (16).
18. Slide wine rack panels (Q) together as
shown.
Note: Please make sure all finished and
unfinished sides are facing the same
way.
18
1
2
3
16
17
1
2
A
3
16
Q
Q
Q
Q

ASSEMBLY INSTRUCTIONS
HARDWARE USED
HARDWARE USED
Wood Dowel x 16
Screw 1-1/4” L x 16
14
19. As shown in Figure 19, insert
assembled wine panels on Figure 18
and wine shelf (U) in assembled unit on
Figure 17.
This step is completed through the
back of the unit.
20. Attach glass rack side (S) and glass
rack middle (T) to assembled unit on
Figure 19 using screws (8) and wood
dowels (1).
Tighten screws with Phillips
screwdriver.
20
19
U
1
8
1
S
T
8
8

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Screw 1/2” x 36
HARDWARE USED
Blot x 8
Allen wrench
15
21. Attach back panels (V) and (W) with
screws (6).
Tighten screws with Phillips
screwdriver.
22. Attach metal rails (Z) to legs (R) with
bolts (14) as shown in Figure 22.
Tighten bolts with Allen wrench (15).
Don’t fully tighten bolts until Figure 23
is complete.
22
15
21
6
W
V
6
14
R
R
Z
Z
15
14

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Blot x 6
Allen wrench
HARDWARE USED
Screw 1/2” L x 18
16
23. Attach assembled unit on Figure 22
to assembled unit on Figure 21 using
bolts (14).
Tighten bolts with Allen wrench (15).
24. Attach left door (X) and right door (Y)
using screws (5).
Tighten all screws with Phillips
screwdriver.
24
5
23
15
14 15
14
5
Y
X

ASSEMBLY INSTRUCTIONS
HARDWARE USED
Screw 1-3/8” L x 4
Bracket x 4
Anchor x 4
Screw 5/8” L x 4
HARDWARE USED
Plastic strap x 2
17
25. Attach brackets (10) to back panels
using screws (13). Tighten screws
using Phillips screwdriver.
Mark two desired locations on wall. Drill
two 3/16" holes on wall. Insert plastic
anchors (12) into 2 holes in wall as
shown.
Tip: You may want to hammer plastic
anchors into wall.
Attach brackets (10) to wall using
screws (9).
Tighten screws (13) using Phillips
screwdriver.
26. Move item close to the wall brackets
(10) and tie in both brackets (10) with
plastic chains strap (11) as shown in
Figure 26.
26
25
9
13
10
12
9
10
1210
13
11
11

ASSEMBLY INSTRUCTIONS
HARDWARE USED
18
27. Your Shadowbox Wine/Bar Cabinet is
ready for use.
27

Please examine this product carefully upon immediate receipt. Any request for missing parts or damage
replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be
honored within this time frame.Parts will not be available for items arriving fully assembled. We do not
recommend modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide
parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at [e-mail]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019