Southern Enterprises Wallingford BT7838A0TX User manual

BT7838A0TX
BT7838B0TX
Wallingford Vanity Sink
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]om
www.seifurniturestore.com

Wallingford Vanity Sink
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or a blanket. Check that you have all parts indicated. Call customer service if any hardware
is missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according
to the pictures. Using the incorrect hardware will cause damage.
A Quantity
of 7
Cam Bolt
B Quantity
of 28
Wood Dowel (Ø8*30)
C Quantity
of 7
Cam Lock
D Quantity
of 2
Bolt （Ø1/4”*1-1/4”）
E Quantity
of 4
Bolt (Ø1/4*1-5/8”)
F Quantity
of 10
Spring Washer（Ø1/4”）
G Quantity
of 10
Flat Washer （Ø1/4”/16mm）
H Quantity
of 6
Knob
I Quantity
of 6
Bolt （Ø5/32”*7/8”）
J Quantity
of 24
Nut
K Quantity
of 24
Bolt （Ø3/16”/1-1/2”）
L Quantity
of 2
Hinge
M Quantity
of 12
Screw (Ø3.5*14mm)
N Quantity
of 2
Screw (Ø8*19mm)
O Quantity
of 15
Screw (Ø3*14mm)
P Quantity
of 4
Bolt （Ø1/4”*2”）

Q Quantity
of 2
Metal Plate
R Quantity
of 6
Bolt （Ø1/4”*1/2”）
1 Quantity
of 1
Top Panel
2 Quantity
of 1
Back splash
3 Quantity
of 1
Left Side Panel
4 Quantity
of 1
Right Side Panel
5 Quantity
of 1
Bottom Panel
6 Quantity
of 1
Middle Divide Panel
7 Quantity
of 1
Front Upper Bar
8 Quantity
of 1
Front Lower Bar
9 Quantity
of 1
Back Upper Bar
10 Quantity
of
1
Back Lower Bar
11 Quantity
of 2
Cross Bar
12 Quantity
of 1
Back panel
13 Quantity
of 1
Door Panel
14 Quantity
of 4
Leg

15 Quantity
of 1
Wood Stopper
16 Quantity
of 3
Drawer Front
17 Quantity
of 3
Left Drawer Side
18 Quantity
of 3
Right Drawer Side
19 Quantity
of 3
Drawer Back
20 Quantity
of 3
Drawer Bottom
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the surface with rough or
abrasive objects.
Call SEI customer service at 1-800-633-5096 for
assistance, questions, or Parts.
Assembly Tool Required:
No.2 Phillips Screwdriver (Not Included)

Wallingford Vanity Sink
Assembly Instructions
Do not overtighten cam bolts. Stop when they feel secure.
Figure 1
Note: Align cam bolts by hand before
using screwdriver.
Insert Cam Locks (C) into
corresponding holes on Front Upper
Bar (7).
Insert Cam Bolts (A) into
corresponding holes on Middle
Divide Panel (6).
Attach Front Upper Bar (7) to Middle
Divide Panel (6) by inserting Cam
Bolts (A) into corresponding holes
until Front Upper Bar (7) and Middle
Divide Panel (6) meet.
Tighten by rotating Cam Locks (C)
clockwise with Phillips screwdriver
(not included).
Notice: Make sure that all finished
edges are facing towards the front
of the unit.
Figure 2
Note: Align Screws by hand before
using screwdriver.
Attach Wood Stoppers (15) to Front
Upper Bar (7) with Screws (N).
Tighten Screws (N) with Phillips
screwdriver (not included).
6
7
C
A
15

Figure 3
Insert Cam Locks (C) into
corresponding holes on Front Upper
Bar (7), Front Lower Bar (8), Back
Upper Bar (9), and Back Lower Bar
(10).
Insert Cam Bolts (A) and Wood
Dowels (B) into corresponding holes
on Left Side Panel (3) and Right Side
Panel (4).
Attach Left Side Panel (3), Right Side
Panel (4), and Cross Bars (11) to
Front Upper Bar (7), Front Lower Bar
(8), Back Upper Bar (9), and Back
Lower Bar (10) by inserting Wood
Dowels (B), Cam Bolts (A), and Bolts
(N) into corresponding holes until all
panels meet.
Tighten by rotating Cam Locks (C)
clockwise with Phillips screwdriver
(not included).
Figure 4
Insert Wood Dowels (B) into the
pre-drilled holes on the
pre-assembled unit from Figure 3.
Align and connect the assembled unit
with the Bottom Panel (5).
Use Bolts (D/P) to secure the panels
in place.
Tighten Bolts (D/P) with Phillips
screwdriver (not included).
C
CA
A
9
7
8
11
10
B
B
B
B
C
B
A
4
3
C
B
BBA
B
B
B
B
B
B
4
3
5

Figure 5
Attach Legs (14) to Bottom Panel (5)
with Bolts (E) and Washers (F/G).
Tighten Bolts (E) with Phillips
screwdriver (not included).
Figure 6
Attach Back Panel (12) to
pre-assembled unit from Figure 5
with Screws (O).
Tighten Screws (O) with Phillips
screwdriver (not included).
14
14
14
14
12
O
O
O
O

Figure 7
Attach the Knobs (H) to the Front
Upper Bar using Bolts (I).
Tighten Bolts (I) with Phillips
screwdriver (not included).
Figure 8
Attach the Hinges (L) to the Doors
(13) using Screws (M).
Tighten Screws (M) with Phillips
screwdriver (not included).

Figure 9
Attach the Door Panel (13) to the
assembled unit using Screws (M).
Tighten Screws (M) with Phillips
screwdriver (not included).
Attach the Knob (H) to the door using
Bolt (I).
Tighten Bolt (I) with Phillips
screwdriver (not included).
Figure 10
Note: Complete this step for all
drawers.
Insert Nuts (J) into corresponding holes
on Drawer Face Panel (16).
Attach Drawer Right Panel and Drawer
Left Panel (18/17) to Drawer Face
Panel (16) with Bolts for Drawer (K).
Insert Drawer Bottom Panel (20) into
inner grooves of Drawer Right Side,
Drawer Left Side Panels (18/17) and
Drawer Face Panel (16).
Insert Nuts (J) into corresponding holes
on Drawer Back Panel (19).
Attach Drawer Back Panel (19) to the
drawer assembly and fasten with Bolts
for Drawer (K).
Attach Knob (H) to Drawer Face Panel
(16) with Bolts (I).
Tighten all Bolts (I) with Phillips
Screw`driver (not included)
17
18
20
19
K
K
K
K
J
J
J
J
J
J
To achieve uniform clearance around the door,
you may need to adjust the door by tightening or
loosening the two screws on the hinge.

Figure 11
Insert the assembled drawers from
Figure 10 into the assembled body.
Figure 12
Loosen the drawer slides as neede
d to adjust the drawer height.