Speco O2P4X User manual

Quick Start Guide
2MP 4X PTZ IP Camera
O2P4X
Version 1.0.1

i
Ta le of Contents
1 DEVICE CHECK ........................................................................................................... 1
1.1 Check Accessories ................................................................................................................................... 1
1.2 Check Device .......................................................................................................................................... 1
1.3 Installation Template .............................................................................................................................. 1
1.4 SD Card Slot and Reset Button ................................................................................................................ 2
2 DEVICE INSTALLATION ............................................................................................... 3
2.1 Component Installation .......................................................................................................................... 3
2.2 Installation Steps .................................................................................................................................... 4
2.2.1 Installation Environment ..................................................................................................................... 4
2.2.2 Installation Steps ................................................................................................................................. 4
3 IP SCANNER .............................................................................................................. 5
3.1 Overview ................................................................................................................................................ 5
3.2 Operation ............................................................................................................................................... 5
4 WEB OPERATION ...................................................................................................... 6
4.1 Login and Main Interface ........................................................................................................................ 6
5 APPENDIX Ⅰ
ⅠⅠ
Ⅰ SURGE PROTECTION ............................................................................... 7
6 APPENDIX Ⅱ
ⅡⅡ
Ⅱ 12V DC WIRE GAUGE AND TRANSMISSION DISTANCE REFERENCE ........... 8
7 APPENDIX Ⅲ
ⅢⅢ
Ⅲ WIRE GAUGE REFERENCE ...................................................................... 9

ii
Welcome
Thank you for purchasing this Network camera!
This manual is esigne to be a reference tool for your system.
Please rea this manual carefully before operating the unit an retain it for future reference.
Shoul you require any technical assistance, please contact Speco Technologies Technical
Support.

iii
Important Safeguards and Warnings
1．
．．
．Electrical safety
All installation an operation here shoul conform to local electrical safety co es.
Use a certifie /liste 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time;
it may result in device damage! The product must e grounded to reduce the risk of
electric shock.
Improper han ling an /or installation coul run the risk of fire or electrical shock.
2．
．．
．Environment
Heavy stress, violent vibration or exposure to water is not allowe uring transportation,
storage an installation.
This pro uct shoul be installe in a cool, ry place away from irect sunlight an heat
sources.
Do not install the pro uct in extreme temperature con itions.
Do not expose the camera to electromagnetic ra iation. Otherwise it may result in CMOS
sensor failure.
Do not block any ventilation openings.
Do not allow water an liqui intrusion into the camera.
3. Operation and Daily Maintenance
Please shut own the evice an then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the ust on
the lens surface.
Always use the ry soft cloth to clean the evice. If there is too much ust, use a cloth
ampene with a small quantity of neutral etergent. Finally use the ry cloth to clean the
evice.
Please use a professional optical cleaning metho to clean the enclosure. Improper
enclosure cleaning (such as using cloth) may result in poor IR functionality an /or IR
reflection.
The groun ing holes of the pro uct are recommen e to be groun e to further enhance
the reliability of the camera.
Dome cover is an optical evice, please on’t touch or wipe cover surface irectly uring
installation an use, please refer to the following metho s if irt is foun :
Staine with irt
Use oil-free soft brush or hair ryer to remove it gently.
Staine with grease or fingerprint

iv
Use oil-free cotton cloth or paper soake with alcohol or etergent to wipe from the lens
center outwar . Change the cloth an wipe several times if it is not clean enough.
Warning
This camera shoul be installe by qualifie personnel only.
All the examination an repair work shoul be one by qualifie personnel.
Any unauthorize changes or mo ifications coul voi the warranty.
Statement
This gui e is for reference only.
Pro uct, manuals an specifications may be mo ifie without prior notice. Speco
Technologies reserves the right to mo ify these without notice an without incurring any
obligation.
Speco Technologies is not liable for any loss cause by improper operation.
Note:
Before installation, check the package an make sure that all components are inclu e .
Keep the package material in case the camera nee s to be sent back for service or repair.
Contact your rep or Speco customer service epartment imme iately if something is broken
or missing in the package.

1
1Device Check
1.1 Check Accessories
Before installation, check the package an make sure that all components are inclu e .
Contact your rep or Speco customer service epartment imme iately if something is broken
or missing in the package.
Accessory Name Amount
Network Camera Unit 1
Quick Start Gui e 1
Junction Box 1
Installation Accessories Bag 1
CD
1
1.2 Check Device
Remove the evice from the package. See Figure 1-1.
Figure 1-1
1.3 Installation Template
The installation template is use for rill hole positioning on the surface. See Figure 1-2.

2
Figure 1-2
1.4 SD Card Slot and Reset Button
SD car slot an button are shown in Figure 1-3.
Please make sure the SD car is in a non rea -write state when removing it. Otherwise, it
may result in ata loss an SD car amage. The button is use for setting the evice back
to a factory efault state. Press an hol the reset button for more than 5 secon s to
activate factory efault.
Figure 1-3

3
2Device Installation
2.1 Component Installation
The installation of pe estal seal ring is shown in Figure 2-1.
Figure 2-1
The installation setup is shown in Figure 2-2.
Figure 2-2

4
2.2 Installation Steps
2.2.1 Installation Environment
The ceiling mount spee ome can be installe on a har surface ceiling in an in oor
environment. Before the installation, please make sure:
The ceiling is thick enough to install the expansion bolt.
The ceiling can sustain at least 8x the weight of the spee ome.
2.2.2 Installation Steps
Step 1
Install the efault pe estal seal ring as shown in Figure 2-1.
Step 2
Confirm the installation position, rill holes on the ceiling accor ing to the installation
template, an then put the three plastic expansion bolts into the holes.
Step 3
Unscrew three locking screws on the enclosure by using the hex wrench, an remove the
enclosure.
Step 4
Use the three self-tapping screws to fix the pe estal on the surface, an insert the screws
into the expansion bolts.
Step 5
Use the three locking screws to fix the ome enclosure on the pe estal.

3IP Scanner
3.1 Overview
IP Scanner can
search for the evice on the local network.
Please note that only evices that are on the same subnet can be iscovere .
3.2 Operation
Open up IP Scanner.
Figure 3-1
In the evice list, you can view the IP a ress, mo el number, an MAC a ress of each
evice
. Select the applicable evice an ouble click to open up the web viewer.
5
search for the evice on the local network.
Please note that only evices that are on the same subnet can be iscovere .
In the evice list, you can view the IP a ress, mo el number, an MAC a ress of each
. Select the applicable evice an ouble click to open up the web viewer.
Figure 3-1 IP Scanner
In the evice list, you can view the IP a ress, mo el number, an MAC a ress of each
. Select the applicable evice an ouble click to open up the web viewer.

4We Operation
This evice supports viewing an management via a web browser on a PC.
4.1
Login and Main Interface
Open the browser an input network camera a ress in the a ress bar or ouble click the
evice in IP Scanner. See
Figure 4
The login interface is shown as below. See
Please input your user name an passwor .
Default user name is admin
an passwor is
Note: For security purposes, please change the password after initial login.
6
This evice supports viewing an management via a web browser on a PC.
Login and Main Interface
Open the browser an input network camera a ress in the a ress bar or ouble click the
Figure 4
-1.
Figure 4-1 IP a ress
The login interface is shown as below. See
Figure 4-2.
Please input your user name an passwor .
an passwor is
1234 .
Note: For security purposes, please change the password after initial login.
Figure 4-2 Web login
Open the browser an input network camera a ress in the a ress bar or ouble click the
Note: For security purposes, please change the password after initial login.
Input your IP
addre
ss
here

7
5APPENDIX Ⅰ
ⅠⅠ
Ⅰ Surge Protection
This evice uses TVS lighting protection technology. It can effectively prevent amages from
various pulse signals below 2000W, such as su en lighting an surge. While maintaining
your local electrical safety co e, you still nee to take necessary precaution measures when
installing the spee ome in an out oor environment.
The istance between the signal transmission cable an high-voltage evice (or high-
voltage cable) shall be at least 50 meters (164 ft).
Out oor cable layout shall go un er the penthouse if possible.
For vast lan , please use sealing steel tube un er the lan to implement cable layout
an connect one point to the earth. Open floor cable layout shoul not be use .
In areas prone to strong thun erstorms or near high sensitive voltage (such as near
high-voltage transformer substation), you nee to install a itional high-power
lightning protection evice or lightning ro .
The lightning protection an earth of the out oor evice an cable shall be consi ere
un er the lightning protection of the whole buil ing an conform to your local national
or in ustry stan ar .
System shall a opt equal-potential wiring. The earth evice shall meet anti-jamming
an at the same time conform to your local electrical safety co e. The earth evice shall
not short circuit to N (neutral) line of high voltage power gri or mixe with other wires.
When connecting the system to earth alone, the earth resistance shall not be more than
4Ω an earth cable cross-sectional area shall be below 25 mm^2.

8
6 APPENDIX Ⅱ
ⅡⅡ
Ⅱ12V DC Wire Gauge and Transmission
Distance Reference
The recommen e max transmission istance is un er the following environments: The
wire iameter is fixe an the DC 12V power voltage loss rate is below 10%. For the evice
being supplie the DC power, the max allowe voltage loss rate is 10%. All the wires liste in
the following sheet are copper wire. (Copper wire resistanceρ = 0.0175Ω ∗ mm
ଶ
/m)
mm
Feet （ m ）
w
0.8000 1.000 1.250 2.000
5 122.13
（ 37.23 ）
190.83
（ 58.16 ）
298.17
（ 90.88 ）
763.31
（ 232.66 ）
10 61.06
（ 18.61 ） 95.41
（ 29.08 ） 149.08
（ 45.44 ）
381.66
（ 116.33 ）
15 40.71
（ 12.41 ） 63.61
（ 19.39 ） 99.39 （ 30.29 ） 254.44
（ 77.55 ）
20 30.53 （ 9.31 ） 47.71 （ 14.54 ） 74.54 （ 22.72 ） 190.83
（ 58.16 ）
25 24.43 （ 7.45 ） 38.17 （ 11.63 ） 59.63 （ 18.18 ） 152.66
（ 46.53 ）
30 20.35 （ 6.20 ） 31.80 （ 9.69 ） 49.69 （ 15.15 ） 127.22
（ 38.78 ）
35 17.45 （ 5.32 ） 27.26 （ 8.31 ） 42.60 （ 12.98 ） 109.04
（ 33.24 ）
40 15.27 （ 4.65 ） 23.85 （ 7.27 ） 37.27 （ 11.36 ） 95.41 （ 29.08 ）
45 13.57 （ 4.14 ） 21.20 （ 6.46 ） 33.13 （ 10.10 ） 84.81 （ 28.85 ）
50 12.21 （ 3.72 ） 19.08 （ 5.82 ） 29.82 （ 9.09 ） 76.33 （ 23.27 ）
55 11.10 （ 3.38 ） 17.35 （ 5.29 ） 27.11 （ 8.26 ） 69.39 （ 21.15 ）
60 10.18 （ 3.10 ） 15.90 （ 4.85 ） 24.85 （ 7.57 ） 63.61 （ 19.39 ）
65 9.39
（ 2.86 ） 14.68 （ 4.47 ） 22.94 （ 6.99 ） 58.72 （ 17.90 ）
70 8.72 （ 2.66 ） 13.63 （ 4.15 ） 21.30 （ 6.49 ） 54.52 （ 16.62 ）
75 8.14 （ 2.48 ） 12.72 （ 3.88 ） 19.88 （ 6.06 ） 50.89 （ 15.51 ）
80 7.63 （ 2.33 ） 11.93 （ 3.64 ） 18.64 （ 5.68 ） 47.71 （ 14.54 ）
85 7.18 （ 2.19 ） 11.23 （ 3.42 ） 17.54 （ 5.35 ） 44.90 （ 13.69 ）
90 6.78 （ 2.07 ） 10.60 （ 3.23 ） 16.56 （ 5.05 ） 42.41 （ 12.93 ）
95 6.43 （ 1.96 ） 10.04 （ 3.06 ） 15.69 （ 4.78 ） 40.17 （ 12.25 ）
100 6.11
（ 1.86 ） 9.54 （ 2.91 ） 14.91 （ 4.54 ） 38.17 （ 11.63 ）

9
7APPENDIX Ⅲ
ⅢⅢ
Ⅲ Wire Gauge Reference
Metric bare wire
iameter
（ mm ）
AWG SWG Bare wire cross
section
（ mm
2
）
0.050 43 47 0.00196
0.060 42 46 0.00283
0.070 41 45 0.00385
0.080 40 44 0.00503
0.090 39 43 0.00636
0.100 38 42 0.00785
0.110 37 41 0.00950
0.130 36 39 0.01327
0.140 35 / 0.01539
0.160 34 37 0.02011
0.180 33 / 0.02545
0.200 32 35 0.03142
0.230 31 / 0.04115
0.250 30 33 0.04909
0.290 29 31 0.06605
0.330 28 30 0.08553
0.350 27 29 0.09621
0.400 26 28 0.1257
0.450 25 / 0.1602
0.560 24 24 0.2463
0.600 23 23 0.2827
0.710 22 22 0.3958
0.750 21 / 0.4417
0.800 20 21 0.5027
0.900 19 20 0.6362
1.000 18 19 0.7854
1.250 16 18 1.2266
1.500 15 / 1.7663
2.000 12 14 3.1420
2.500 / / 4.9080
3.000 / / 7.0683