SPI 20-186-3 User manual

IP54 Absolute Digital
Indicator Probes
(Inch/Metric)
Operation Manual
0 - .5" 20-186-3
0 - 1" 20-187-1
0 - 2" 20-188-9
0 - 4" 20-189-7
© 2017 Swiss Precision Instruments, Inc.
Compatible with
DIGITAL HEIGHT GAGES
Absolute Encoder Technology
• Large LCD display.
• Inch / Metric conversion at any position.
• Heavy duty hardened stainless steel beam.
• Data cable to connect indicators to height gages
included.
• SPC/USB data output.
• Zero setting at any position.
• Resolution 0.0005"/0.01 mm
• Manual On/Off power.
• Carbide tipped scriber.
• Indicator bar for travel indicator included.
• Smooth slider feed wheel.
• Battery CR2032 included.
• Furnished in fitted case.
Connect with Absolute Digital Indicator Probes
• Connecting an SPI Digital Indicator Probe to
the height gage will increase the resolution
of the height gage to 0.00005".
• Origins are set to height gage and indicator
simultaneously.
• Height gage can not be moved up or down after ori-
gins have been set.
RANGE ACCURACY PART NO.
0 - 12"/0 - 300 mm ±0.001"/±0.01 mm 11-959-4
0 - 18"/0 - 450 mm ±0.002"/±0.05 mm 11-960-2
0 - 24"/0 - 600 mm ±0.0025"/±0.06 mm 11-961-0
11-959-4
20-189-7
20-187-1 Indicator Probes.indd 1 2/20/17 10:00 AM

Please refer to the enclosed warranty card
for warranty information.
Table
1 SPC/USB data port
2 LCD display
3 Battery holder
3V CR1632
4 Gage body
5 3/8" dia. shank
6 Finger Lift
7 4 - 48 Thread
(Carbide Point)
8 Lugback (removable)
9 Lugback screw
10 Screwdriver
1
2
4
58
6
7
3
Specications:
Range Resolution Accuracy ± Repeatability
0 - .5"
0 - 1" 0.0002"
0 - 2" 0.00005" 0.00005"
0 - 4" 0.0003"
Absolute encoder digital indicator probes always
remembers and tracks absolute origin zero and preset
data. Provides unlimited measure speed and IP54
protection. It will indicate absolute position when
turned on and ready to measure. Comes with
SPC/USB data port and uses SPC/USB Interface
& Cable 11-967-7 or Wireless Data Output 17-599-2
(not included).
Origin Button:
Press the Origin button for 3 seconds to set.
On/Off Button:
A short press of the On/Off button will turn on or off
the indicator probe.
Preset Button:
Press the "PRESET" button for 3 seconds to enter
the setup mode. "P" will begin to ash, by long
pressing the "PRESET" button, numerical digits will
ash one by one. Press the "PRESET" to change
the value of the ashing digit. After completing the
presetting process, long press the "PRESET"
button to exit the PRESET mode. A new preset val-
ue has been stored. Then long press the "ORIGIN"
button, the LCD will display the preset value.
IN/MM Button:
Interchange between inch and metric reading.
Travel Reverse (+/-) Button:
Switch between + or - measurement directions.
Use with Care:
• Keep the tool clean and dry.
• Avoid shocks or impacts.
• Do not drop indicator probe.
• Avoid magnetic elds.
Optional Accessories
SPC/UBS
Interface & Cable
11-967-7
Wireless
Data Output
17-599-2
10
9
20-187-1 Indicator Probes.indd 2 2/20/17 10:00 AM