Sport-thieme 113 6526 User manual

D-38367 Grasleben ·Germany
sport-thieme.com · info @sport-thieme.com
Phone: [phone] · Fax: [phone]
Thanks for choosing Sport-Thieme equipment!
In order to enjoy this product please note the following instructions for safety, use and maintenance before assembly.
Assembly instruction Cat.-no.
: 113 6526
0118814 · © 2018 Sport-Thieme GmbH
Cat.-no. 113 6526:
Sport-Thieme®
Handball Goal, 3x2 m,
without net brackets, in
ground sockets
Sport-Thieme®
Handball Goal
3x2 m, without net brackets, in ground sockets

2
Assembly instruction Cat.-no. 113 6526
1. Scope of delivery
Please check the following content before assembly.
The following indicated quantities refer to 1 Handball goal. In case of a delivery in pairs we double the
amount correspondingly. Pictured colours of proles are only samples and may dier from delivered pro-
les.
Accessories
Piece Description
1Crossbar, prole 80 x 80mm
2Uprights, prole 80 x 80mm
Piece Description
2Aluminium cast corner joints
2Upright cap
1 Accessories
Stück Beschreibung
2Ground socket, length 300 mm
2Cap for ground socket
Stück Beschreibung
32 Net holder
8Hexagon socket screw M8 x 20, DIN 7991
1Plug pin
1Hexagon screwdriver SW5, DIN 911, black
1Assembly instruction

3
Assembly instruction Cat.-no. 113 6526
2. Assembly of the goal
The following tools are necessary:
- 2 wrench/ring spanners 13 mm
- 1 mallet/hammer
- 1 drill Ø 1,5 mm
- 1 thin screw driver (for net hook xing if necessary)
a) Assembly of crossbar/uprights: Lay crossbar and uprights on the ground, groove facing upwards and mitres joining. Stick alu-
minium cast corner joint into the end of the crossbar (see 2nd picture bottom right). Then stick upright on cast corner joint.
Take care that the internal corner of crossbar/upright is nearly closed. The external corner has to be somewhat open as
shown on the 3rd picture below. Screw 2 hexagon socket screws DIN 7991, M8 x 20mm in the internal corner (see 4th picture
bottom right).
upright
crossbar
1. stick aluminium cast corner joint
2. push mitre of internal
corner close together
3. let external corner
still open
4. screw hexagon socket
screws M8 x 20mm slightly

4
Assembly instruction Cat.-no. 113 6526
Then join uprights at the external corner. Adjust crossbar and uprights. Screw 2 hexagon socket screws DIN 7991, M8 x 20mm
in the external corner (see picture bottom right) and tighten all screws.
Advice: Due to production tolerances of the aluminium cast corner joints problems during adjustment of corners may pos-
sibly occur. Then shorten the stamps in the uprights with a flat le.
b) Assembly of caps: Stick caps in the open ends of uprights (see picture bottom left). Bore them with drill 1.5 mm through the
holes provided in the uprights. Then x plug pins with a hammer/mallet (see picture bottom right).
join and adjust
corner
Between standing

5
Assembly instruction Cat.-no. 113 6526
3. Assembly of the net
a) The net is not part of the delivery.
Fix net holders at the net rope. Bend open net holders a little and press rope into the holders. We recommend the following
distribution of net holders:
crossbar : 16 pieces
uprights : 8 pieces each
b) After having mounted all net holders x net at the goal construction. Stick net holders in the net hook rail and x them with a
90 degrees’ rotation. Use a thin screw driver if necessary (please avoid damages at the goal).
c) Dismantling of the net is also done by rotation of the net holders through 90 degrees. Use again a thin screw driver if neces-
sary.
4. Assembly of the ground sockets
a) For handball gates with a size of 3,00 x 2,00 m the distance of the ground sockets must be 3,08 m (middle socket – middle
socket = center distance).
b) Concrete ground sockets according to the sketch. Foundation dimensions: 800 x 800 x 800 mm.
c) Do not apply an acceleration mixture or antifreeze during as these adhesives may cause damages to the ground sockets.
d) After hardening of the concrete, the goal can be inserted into the sockets.

6
Assembly instruction Cat.-no. 113 6526
5. Maintenance, safety and storage instructions
This goal is only constructed for Handball and not for other purposes. Check all screwed
fastenings before use and repeat it from time to time. It has to be protected against over-
turning at any time.
Do not climb net or goal frame. It is not allowed to x additional parts or extensions at the
goal frame which may impair the safety of the goal (according to EN 749).
Check screwed fastenings regularly and change damaged and wearing parts if need be. The unit should be maintained once a
year by skilled personnel.
Notice
Due to our continuous quality check of products and equipment technical modications are possible.
To avoid damage and misuse goals have to be stored secured and in an upright position when not in use.
Only use water for cleaning the surfaces. Do not use alcohol or any aggressive chemicals!
All images and texts are intellectual property of Haspo Sportgeräte GmbH & Co. KG.
Any usage requires explicit permission.