SportDOG sd-825e User manual

OPERATING GUIDE
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING

2SPORTDOG.COM
Hereinafter Radio Systems Corporation, Radio Systems PetSafe Europe Ltd., Radio Systems Australia Pty Ltd.
and any other affiliate or Brand of Radio Systems Corporation may be referred to collectively as “We” or “Us”.
IMPORTANT SAFETY INFORMATION
EXPLANATION OF ATTENTION WORDS AND SYMBOLS USED IN THIS GUIDE
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if
not avoided, could result in harm to your dog.

3SPORTDOG.COM
• Not for use with aggressive dogs. Do not use this product if your dog is aggressive or if your dog is prone to
aggressive behaviour. Aggressive dogs can cause severe injury and even death to their owner and others.
If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or a
certified trainer.
• This device contains Lithium-Ion (Li-Ion) batteries; never incinerate, puncture, deform, short-circuit, or
charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this
warning is not followed.
• Risk of explosion if battery is replaced by an incorrect type. Dispose of spent batteries according to the
regulations in your area.
• Batteries should never be removed from the battery compartment for charging.
• Risk of explosion if batteries are charged in areas with high temperature (38° C / 100° F+).
Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for
too long or made too tight on the dog’s neck may cause skin damage. This is called bed sores; it is also called
decubitus ulcers or pressure necrosis.
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible, reposition the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the Collar Receiver; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian. For additional information on bed sores and
pressure necrosis, please visit our website at www.sportdog.com.
These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable while they wear
stainless steel contacts. Some dogs are sensitive to contact pressure. You may find after some time that your
dog is very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue daily
checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed.
• You may need to trim the hair in the area of the Contact Points or switch to the longer Contact Points to
ensure consistent contact. Never shave the dog’s neck; this may lead to a rash or infection.
• You should not make the collar any tighter than is required for good contact. A collar that is too tight will
increase the risk of pressure necrosis in the contact area.

4SPORTDOG.COM
Thank you for choosing SportDOG®Brand training products. Used properly, this product will help you train your
dog efficiently and safely. To ensure your satisfaction, please review this Operating Guide thoroughly. If you
have questions regarding this product’s operation, please see this manual’s Frequently Asked Questions and
Troubleshooting sections or contact our Customer Care Centre. For a listing of telephone numbers in your area,
visit our website at www.sportdog.com.
To get the most protection out of your warranty, please register your product within 30 days at
www.sportdog.com. By registering and keeping your receipt you will enjoy the product’s full warranty and,
should you ever need to call the Customer Care Centre, we will be able to help you faster. Most importantly, your
valuable information will never be given or sold to anyone. Complete warranty information is available online at
www.sportdog.com.
TRAINING GUIDE
Please visit our website at www.sportdog.com to download a detailed Training Guide for this unit or contact our
Customer Care Centre for further assistance. For a listing of telephone numbers in your area, visit our website
at www.sportdog.com.
TABLE OF CONTENTS
COMPONENTS 5
HOW THE SYSTEM WORKS 5
KEY DEFINITIONS 6
PREPARE THE REMOTE TRANSMITTER 7
PREPARE THE COLLAR RECEIVER 8
FIT THE COLLAR RECEIVER 10
FIND THE BEST INTENSITY LEVEL FOR YOUR DOG 11
CHANGE STATIC STIMULATION RANGES 11
GENERAL TRAINING TIPS 12
PROGRAM THE REMOTE TRANSMITTER 13
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER 15
PROGRAM THE SYSTEM FOR TWO OR THREE-DOG OPERATION 15
CHANGE ID CODES 16
ACCESSORIES 16
FREQUENTLY ASKED QUESTIONS 16
TROUBLESHOOTING 18
TEST LIGHT TOOL INSTRUCTIONS 18
TERMS OF USE AND LIMITATION OF LIABILITY 19
COMPLIANCE 19
BATTERY DISPOSAL 20
IMPORTANT RECYCLING ADVICE 20
WARRANTY 21

5SPORTDOG.COM
COMPONENTS
HOW THE SYSTEM WORKS
The SportDOG®SportTrainer®SD-825E Remote Trainer has been proven safe, comfortable, and effective for all
dogs over 3.6 kg. Consistent, correct use of this product allows you to reinforce commands and correct
misbehaviour from up to 700 metres. The Remote Transmitter sends a signal, activating the Collar Receiver to
deliver a harmless stimulation. With proper training, a dog will learn to associate this signal with a command.
Like all SportDOG®products, this model features adjustable static stimulation levels so you can tailor the
stimulation level to your dog’s temperament, eliminating the risk of over-stimulation.
IMPORTANT: THE SPORTTRAINER®SD-825E REMOTE TRAINERS HAS A RANGE OF UP TO
700 M. DEPENDING ON THE WAY YOU HOLD THE REMOTE TRANSMITTER, THE MAXIMUM
RANGE MAY VARY. FOR CONSISTENT RESULTS AT LONGER RANGES, HOLD THE REMOTE
TRANSMITTER IN A VERTICAL POSITION AWAY FROM YOUR BODY AND ABOVE YOUR
HEAD. TERRAIN, WEATHER, VEGETATION,TRANSMISSION FROM OTHER RADIO DEVICES,
AND OTHER FACTORS WILL AFFECT THE MAXIMUM RANGE.
Do not use this product if your dog is aggressive or if your dog is prone to aggressive behaviour. Aggressive
dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product
is appropriate for your dog, please consult your veterinarian or a certified trainer.

6SPORTDOG.COM
KEY DEFINITIONS
REMOTE TRANSMITTER: Transmits the radio signal to the Collar Receiver. It is waterproof and can be submerged
in water to a depth of 7.6 m.
INTENSITY DIAL: Provides multiple levels and types of stimulation so you can match the stimulation to your
dog’s temperament.
TRANSMITTER INDICATOR LIGHT: Indicates that a button is pressed and also serves as a low-battery indicator.
UPPER BUTTON: This button is factory-set to deliver continuous static stimulation.
LOWER BUTTON: This button is factory-set to deliver momentary static stimulation, or a “Nick”.
SIDE BUTTON: This button is factory-set to deliver a tone without static stimulation.
CHARGING JACK: For connecting the charger. Although the Remote Transmitter is waterproof without it, keep the
cover in place when not charging to keep debris out of the opening.
MODE BUTTON: This button gives you the ability to change the mode of your Remote Transmitter.
COLLAR RECEIVER: Receives the radio signal from the Remote Transmitter and delivers the static, vibration,
or tone stimulation for correcting or cueing your dog. It is waterproof and can be submerged in water to a
depth of 7.6 m.
RECEIVER INDICATOR LIGHT: Indicates when the Collar Receiver has been turned on or off, serves as a low-
battery indicator, and also indicates when a continuous or momentary (nick) static stimulation button is pressed.
CONTACT POINTS: The contacts through which the Collar Receiver delivers static stimulation.
ON/OFF BUTTON: Momentarily pressing and releasing this button turns the Collar Receiver on and off.
THE COLLAR RECEIVER IS CAPABLE OF DELIVERING FOUR TYPES OF STIMULATION:
CONTINUOUS: You control both when and how long static stimulation is delivered, up to a maximum of 10
seconds. After 10 seconds, the Remote Transmitter will “time out” and static stimulation cannot be delivered to
your dog for 5 seconds. After the 5 second “time-out” period, static stimulation can be delivered again.
MOMENTARY (NICK): Static stimulation is delivered for 1/10 of a second, regardless of how long the button
is pressed.
TONE: The Collar Receiver will make a rapid beeping noise when a Tone button is pressed.
VIBRATION (VIBE): The Collar Receiver will vibrate when a Vibration button is pressed, up to a maximum of 10
seconds. After 10 seconds, the Remote Transmitter will “time out” and vibration stimulation cannot be delivered
to your dog for 5 seconds. After the 5 second “time-out” period, vibration stimulation can be delivered again.
TRANSMITTER
INDICATOR LIGHT
INTENSITY DIAL
TRANSMITTER
ANTENNA
SIDE BUTTON
LOWER
BUTTON
UPPER
BUTTON
CHARGING JACK
CONTACT POINTS
RECEIVER
INDICATOR LIGHT
ON/OFF BUTTON

7SPORTDOG.COM
STEP::01
PREPARE THE REMOTE TRANSMITTER
CHARGE THE REMOTE TRANSMITTER
1. Lift the rubber cover protecting the Charging Jack.
2. Connect one of the charger connectors to the
Charging Jack.
3. Plug the charger into a standard wall outlet.
4. Charge the Remote Transmitter for 2 hours for the first
charge and every charge thereafter.
Using Lithium-Ion technology, the Remote Transmitter only
requires a 2 hour charge. It is not harmful to let the unit charge
for more than 2 hours.
5. When charging is complete, replace the rubber cover.
Note: Approximate battery life between charges is 50 to 70
hours, depending on frequency of use.
TRANSMITTER INDICATOR LIGHT
OPERATIONAL MODE LIGHT COLOUR BATTERY STATUS LIGHT FUNCTION
Continuous static tone, or
vibration stimulation pressed Green Good Light is solid in colour while button is pressed
Continuous static, tone, or
vibration stimulation pressed Red Low Light is solid in colour while button is pressed
Momentary static stimulation
button pressed Green Good Light flashes once and turns off
Momentary static stimulation
button pressed Red Low Light flashes once and turns off
Unit is charging Green Low Light is solid in colour
while charging
Unit is fully charged (charger
still connected) Green Good
Light flashes once per
second once the battery is
completely charged
CHARGER
CONNECTOR PLACED
IN THE REMOTE
TRANSMITTER
CHARGING JACK

8SPORTDOG.COM
STEP::02
PREPARE THE COLLAR RECEIVER
CHARGE THE COLLAR RECEIVER
1. Lift the rubber cover protecting the Charging Jack.
2. Connect one of the charger connectors to the Charging Jack.
3. Plug the charger into a standard wall outlet.
4. Charge the Collar Receiver for 2 hours for the first charge and every charge thereafter.
Using Lithium-Ion technology, the Collar Receiver only requires a 2 hour charge. It is not harmful to let the unit
charge for more than 2 hours.
5. When charging is complete, replace the rubber cover.
TO TURN THE COLLAR RECEIVER ON
Press and release the On/Off Button. The Collar Receiver
Indicator Light will come on and the Collar Receiver will
beep 1 - 2 times depending on what static stimulation range is
chosen. The default is 2 (medium).
TO TURN THE COLLAR RECEIVER OFF
Press and release the On/Off Button. The Receiver Indicator
Light comes on solid (red) and the Collar Receiver beeps
continuously for 2 seconds.
To extend the life between charging cycles, turn the Collar
Receiver off when it is not in use.
NOTE: Approximate battery life between charges is 50 to 70 hours, depending on frequency of use.
RECEIVER INDICATOR LIGHT
OPERATIONAL
MODE
LIGHT
COLOUR
BATTERY
STATUS LIGHT FUNCTION SPEAKER FUNCTION VIBRATION
Unit is turned on via
On/Off Button Green Good Light is solid in colour during beep sequence
Beeps 1-2 times
depending on static
stimulation range
setting (2 is the
default). Please see
page 11.
N/A
Unit is turned on via
On/Off Button Red Low Light is solid in colour during beep sequence
Unit is turned off via
On/Off Button Red N/A Light is solid in colour during beep sequence
Beeps continuously
for 2 seconds N/A
Unit is on Green Good Light flashes every
2 seconds N/A N/A
Unit is on Red Low Light flashes every
2 seconds N/A N/A
Unit is delivering
continuous static
stimulation
Red N/A
Light is solid in colour
for as long as button
is pressed (up to
10 seconds)
N/A N/A
Unit is delivering
momentary (nick)
static stimulation
Red N/A
Light will quickly flash
once no matter how long
button is pressed
N/A N/A
CHARGER CONNECTOR PLACED
IN THE COLLAR RECEIVER
CHARGING JACK
ON/OFF BUTTON

9SPORTDOG.COM
RECEIVER INDICATOR LIGHT
OPERATIONAL
MODE
LIGHT
COLOUR
BATTERY
STATUS LIGHT FUNCTION SPEAKER FUNCTION VIBRATION
Unit is delivering
tone stimulation Off N/A N/A
Unit will beep for
as long as button is
pressed
N/A
Unit is delivering
vibration
stimulation
Off N/A N/A N/A
Unit will vibrate
for as long
as button is
pressed (up to
10 seconds)
Unit is charging Green Low Light is solid in colour
while charging N/A N/A
Unit is fully
charged (charger
still connected)
Green Good
Light flashes once per
second once the battery
is completely charged
N/A N/A
RECHARGEABLE BATTERIES
• This device contains Lithium-Ion (Li-Ion) batteries; never incinerate, puncture, deform, short-circuit, or
charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this
warning is not followed.
• Risk of explosion if battery is replaced by an incorrect type. Dispose of spent batteries according to the
regulations in your area.
• Batteries should never be removed from the battery compartment for charging.
• Risk of explosion if batteries are charged in areas with high temperature (38° C / 100° F+).
• The rechargeable Lithium Ion (Li-Ion) batteries are not memory sensitive, do not require depletion before
charging, and cannot be over charged.
• The batteries come partially charged from the factory, but will require a full charge before the first use.
• When storing the unit for long periods, remember to regularly give batteries a full charge. This should be
done once every 3 to 4 months.
• You should expect hundreds of recharge cycles from your batteries. However, all rechargeable batteries
lose capacity over time relative to the number of recharge cycles they experience. This is normal. If your
operating time drops to half of the original life, contact the Customer Care Centre to purchase a new battery.
• The batteries should last for a period of 3-5 years. When a battery needs replacement, you can order a new
pack by calling our Customer Care Centre. For a listing of telephone numbers in your area, visit our website
at www.sportdog.com. Please do not open the Collar Receiver or Remote Transmitter until you have received
the replacement.

10 SPORTDOG.COM
STEP::03
FIT THE COLLAR RECEIVER
IMPORTANT: The proper fit and placement of the Collar Receiver is important for effective training. The Contact
Points must have direct contact with your dog’s skin.
Please see page 3 for Important Safety Information.
To ensure a proper fit, follow these steps:
1. With your dog standing (3A), center the
Collar Receiver so the Contact Points are
underneath your dog’s neck, touching the
skin (3B). If your dog has a long or thick coat,
you have two options to ensure consistent
contact: either trim the hair around the
Contact Points or switch to the longer
Contact Points included with your system.
• You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck; this may lead to
a rash or infection.
• You should not make the collar any tighter than is required for good contact. A collar that is too tight will
increase the risk of pressure necrosis in the contact area.
2. The Collar Receiver should fit snugly, yet loose enough to allow one finger to fit
between the strap and your dog’s neck (3C).
3. Allow your dog to wear the collar for several minutes, and then recheck the
fit. Check the fit again as your dog becomes more comfortable wearing the
Collar Receiver.
3A 3B
3C

11 SPORTDOG.COM
STEP::04
FIND THE BEST INTENSITY LEVEL FOR YOUR DOG
The SportTrainer®SD-825E Remote Trainer has multiple intensity levels. This allows you to choose the static
stimulation that is best for your dog.
NOTE: Always start at the lowest level and work your way up.
For training efficiency, it is important to find the right intensity level for your dog. This is called the “Recognition
Level”, and is the level at which your dog looks around in curiosity or flicks his ears.
TO FIND YOUR DOG’S RECOGNITION LEVEL
NOTE: Every dog is different and you cannot predict where your dog’s Recognition Level will be. Watch closely for
any slight change in behaviour that demonstrates your dog is feeling the static stimulation.
1. With the Collar Receiver turned on and properly fitted to your dog, set the Remote Transmitter’s Intensity
Dial at Level 1 and press the Continuous Static Stimulation Button for 1 to 2 seconds.
2. If your dog shows no reaction to Level 1, go to Level 2 and repeat the process.
3. YOUR DOG SHOULD NOT VOCALIZE OR PANIC WHEN RECEIVING STATIC STIMULATION. IF THIS HAPPENS,
THE STATIC STIMULATION LEVEL IS TOO HIGH AND YOU NEED TO GO BACK TO THE PREVIOUS LEVEL AND
REPEAT THE PROCESS.
4. Once you find your dog’s Recognition Level, this is the level you should use when you begin a
training exercise.
5. If you have progressed to Level 7 while searching for your dog’s Recognition Level and your dog continues
to show no response, check to see if the Collar Receiver is snug against your dog’s neck. Then go back to
Intensity Level 1 and repeat the process. If your dog still does not indicate he is feeling the static stimulation,
you have three options: trim the hair beneath the Contact Points, switch to the longer Contact Points included
in your system, or change the static stimulation range.
If after completing all of these steps your dog still does not indicate he is feeling the static stimulation, please
contact the Customer Care Centre.
CHANGE STATIC STIMULATION RANGES
The SportTrainer®SD-825E Collar Receiver has 2 static stimulation ranges (low and medium). There are 7 static
stimulation levels within each range, with 1 being the lowest and 7 being the highest. The default range setting is
2 (medium).
To change the range of static stimulation, follow these steps:
1. Make sure the Collar Receiver is off.
2. Turn the unit on by pressing and releasing the On/Off Button.
3. Within 5 seconds of the indicator light turning off, press and hold the On/Off Button for 3 seconds.
4. The Collar Receiver will then beep once and the Indicator Light will flash orange. This indicates Low static
stimulation range. If Medium is desired, continue to hold the On/Off Button until the Collar Receiver beeps
twice and the Indicator Light flashes orange twice, as shown in the chart below.
5. Release the On/Off Button once the desired range is selected; the Collar Receiver will turn off.
6. Turn the unit back on. It will then beep according to the static stimulation range selected in STEP::04.
STATIC STIMULATION RANGE DOG TEMPERAMENT
1 beep Low Mild
2 beeps Medium Moderate

12 SPORTDOG.COM
GENERAL TRAINING TIPS
BEFORE TRAINING YOUR DOG WITH THIS PRODUCT
You will have the most success using this Remote Trainer if you always remember to teach a command before
trying to reinforce the command with the Remote Trainer. Always keep the following training tips in mind:
• Eliminate one misbehaviour or teach one obedience command at a time. If you move too fast with the training,
your dog may become confused.
• Be consistent. Give your dog a static, tone, or vibration stimulation with each misbehaviour.
• Do not overcorrect your dog. Use as few stimulations as possible to train your dog.
• Restrict your dog from situations in which he has a history of misbehaving unless you can supervise him and
use the Remote Trainer for applying static, tone, or vibration stimulation.
• If you notice one situation in which your dog misbehaves repeatedly, set up this situation as a training session.
This will dramatically increase your chances of success.
• If your dog has a timid reaction to the static, tone, or vibration stimulation (especially the first couple
of times), do not be alarmed. Redirect his attention to a simple and appropriate behaviour (i.e. a known
command, such as “Sit”).
• Never use the Remote Trainer to correct or eliminate any form of aggressive behaviour. If your dog exhibits
such behaviour, contact a professional trainer. Aggression in dogs is the result of many factors. It may be a
learned behaviour or it may be brought on as a result of fear. Another factor contributing to aggression in
dogs is social dominance. Every dog is different.
Visit our website at www.sportdog.com to find more detailed training tips and guides or contact our Customer
Care Centre for further assistance. For a listing of the phone numbers in your area, visit our website at
www.sportdog.com.
At this point, your Remote Trainer is ready to use. The Remote Transmitter is factory set to mode 1, but you may
wish to change the mode to fit your situation. See STEP::05 for an explanation of mode options.

13 SPORTDOG.COM
STEP::05
PROGRAM THE REMOTE TRANSMITTER
The SportTrainer®SD-825E has seven operational modes to allow you to select the best match for your type or
style of training. The Remote Transmitter is factory set to mode 1. There is also one programming mode: Mode
V/T (Change ID Codes).
TO CHANGE THE MODE
1. Referring to the following table, adjust the Intensity Dial to
your desired mode.
2. Turn the Remote Transmitter over.
3. Using a pen or the tine on the buckle of your collar strap,
press and release the Mode Button. When the Mode Button is
pressed, the Transmitter Indicator Light will be solid in colour.
When it is released, it will flash the number of times for the
mode selected.
For example, if mode 5 is desired, adjust the Intensity Dial to Level 5. Once the Mode Button has been depressed,
the Transmitter Indicator Light will be solid and, once the mode button is released, the Transmitter Indicator
Light will flash 5 times.

14 SPORTDOG.COM
MODE UPPER BUTTON FUNCTION LOWER BUTTON FUNCTION SIDE BUTTON FUNCTION NUMBER
OF DOGS
1*
Continuous static stimulation
(Level set by Intensity Dial)
OR
Vibration stimulation if V/T
on Dial
Momentary static stimulation
(Level set by Intensity Dial)
OR
Vibration stimulation if V/T
on Dial
Tone stimulation only 1
2
Continuous static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
Momentary static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
Vibration stimulation only 1
3
Dog 1:
Continuous static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
Dog 2:
Continuous static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
Dog 3:
Continuous static
stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T
on Dial
3
4
Dog 1:
Continuous static stimulation
(Level set by Intensity Dial)
OR
Vibration stimulation if V/T
on Dial
Dog 2:
Continuous static stimulation
(Level set by Intensity Dial)
OR
Vibration stimulation if V/T
on Dial
Dog 3:
Continuous static
stimulation
(Level set by Intensity Dial)
OR
Vibration stimulation if
V/T on Dial
3
5
Continuous static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
Momentary static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
N/A 1
6
Continuous static stimulation
(Level set by Intensity Dial)
OR
Vibration stimulation if
V/T on Dial
Momentary static stimulation
(Level set by Intensity Dial)
OR
Vibration stimulation if
V/T on Dial
N/A 1
7
Continuous static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
Momentary static stimulation
(Level set by Intensity Dial)
OR
Tone stimulation if V/T on Dial
Locate Remote Beeper** 1
V/T
(ID
CODE)
N/A N/A See STEP::08 N/A
* Factory Default Mode
** Locate Remote Beeper: The Side Button turns Run Mode off and locates the Remote Beeper. To enable Run Mode
again, press and hold the Side Button for 3 seconds.

15 SPORTDOG.COM
STEP::06
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER
To match the Collar Receiver to work with a new Remote Transmitter or to match a new Collar Receiver to work
with your existing Remote Transmitter:
1. Turn the Collar Receiver off.
2. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 4-5 seconds.
If the On/Off Button is released too early, the Receiver Indicator Light will begin flashing as normal. If this
occurs, start over from 1.
3. After the Receiver Indicator Light has turned off, release the On/Off Button.
4. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5
times. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been matched and will
begin flashing as normal. If the Receiver Indicator Light does not flash 5 times, start over from 1.
STEP::07
PROGRAM THE SYSTEM FOR TWO OR THREEDOG OPERATION
SportDOG®Add-A-Dog®extra Collar Receiver(s) must be purchased to train additional dogs. Please refer to the
last page for compatible Add-A-Dog®extra Collar Receivers for this system.
1. Program the Remote Transmitter to mode 3 or 4 (see STEP::05).
2. Program the first Collar Receiver.
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 4-5
seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin its normal
flashing. If this occurs, start over from A.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5
times. If the Receiver Indicator Light does not flash 5 times, start over from A.
3. Program the second Collar Receiver using A through D above, but using the Lower Button in place of the
Upper Button.
4. Program the third Collar Receiver using A through D above, but using the Side Button in place of the
Upper Button.

16 SPORTDOG.COM
STEP::08
CHANGE ID CODES
An ID Code is the signal identification between the Remote Transmitter and Collar Receiver. Each is programmed
in 1 of 2,000 ID Codes from the factory. The SportTrainer®SD-825E has the flexibility to program two or more
Remote Transmitters to the same ID Code, allowing them to both control one Collar Receiver. There are 64
programmable ID Codes available.
TO MANUALLY PROGRAM A REMOTE TRANSMITTER’S ID CODE
1. Turn the Intensity Dial to V/T and then press and release the Mode Button on the back of your Remote
Transmitter. This does not change the mode, so the current mode will still be active after the ID change
is complete.
2. Once the Mode Button is released, the Transmitter Indicator Light will illuminate solid green and stay on for
15 seconds.
3. While the green Indicator Light is on, turn the Intensity Dial to select the 1st digit of the ID and then press and
release the Side Button. The green Indicator Light will flash rapidly confirming selection.
4. Again, while the green Indicator Light is on, turn the Intensity Dial to select the 2nd digit of the ID and then
press and release the Side Button. The green Indicator Light will flash rapidly confirming selection. The
2nd digit is optional and, if not desired, wait until the green light turns off and refrain from pressing the
Side Button.
5. At the end of 15 seconds, or after the second press of the Side Button, the green Indicator Light will turn off
and the ID of the Remote Transmitter will be updated. At this point, the Remote Transmitter will be in the
same mode it was in prior to setting the ID.
6. Upon changing the ID Code, you will need to match the Collar Receiver to the Remote Transmitter
(see STEP::06).
TO RETURN THE REMOTE TRANSMITTER TO THE FACTORY ID
1. Turn the Intensity Dial to V/T and then press and release the Mode Button on the back of your Remote
Transmitter. This does not change the mode, so the current mode will still be active after the ID change
is complete.
2. Do not press any buttons and wait until the green Transmitter Indicator Light turns off.
3. You will need to match the Collar Receiver to the Remote Transmitter (see STEP::06).
NOTE: Removing the battery will also return the Remote Transmitter to the factory ID.
ACCESSORIES
To purchase additional accessories for your SportDOG®SportTrainer®SD-825E Remote Trainer, contact the
Customer Care Centre or visit our website at www.sportdog.com to locate a retailer near you.
FREQUENTLY ASKED QUESTIONS
Is the static stimulation safe
for my dog?
While Continuous static and/or Momentary static stimulation may be
unpleasant, it is harmless to your dog. Electronic training devices require
interaction and training from the owner to achieve desired results.
How old does a dog have
to be before using the
Remote Trainer?
Your dog should be able to learn basic obedience commands such as “Sit” or
“Stay”. The system should only be used with dogs over 6 months of age. The
Collar Receiver may be too large for dogs under 3.6 kg. If your pet is injured or
its mobility is otherwise impaired, contact your veterinarian or professional
trainer before use.

17 SPORTDOG.COM
FREQUENTLY ASKED QUESTIONS
Once my dog is trained
and has been obeying my
commands, will my dog
have to continue to wear the
Collar Receiver?
Your dog may need to wear the Collar Receiver from time to time for
reinforcement. Also, many hunters keep the Collar Receiver on their dogs
while hunting for maximum control.
Is the Collar Receiver
waterproof?
Yes. If the rechargeable battery pack ever needs to be replaced, make sure the
o-ring and o-ring groove are free from dirt and debris.
Can my Collar Receiver be
used around salt water?
Yes. However, if the Collar Receiver is used in or around salt water, it should
be rinsed with fresh water following each use.
Can I use the Remote Trainer
with more than one dog?
Yes. The SportTrainer®SD-825E Remote Trainer is expandable to a maximum
of 3 dogs. SportDOG®Add-A-Dog®Collar Receivers must be purchased. Please
refer to the last page for a list of compatible Collar Receivers.
Can I use the Remote Trainer
on aggressive dogs?
We do not recommend any of our products to be used on aggressive dogs. We
recommend you contact your local veterinarian or professional trainer to
determine if your dog might be aggressive.
Will I get exactly 700 m
of range with the Remote
Trainer?
The range you get with your Remote Trainer will vary according to terrain,
weather, and vegetation as well as transmission from other radio devices.
To get the maximum amount of range, please refer to “HOW THE SYSTEM
WORKS” section of this guide.
How long can I continuously
deliver stimulation to my dog?
The maximum amount of time you can press the Continuous Static
Stimulation Button and deliver static stimulation to your dog continuously
is 10 seconds. The maximum amount of time you can press the vibration
button and deliver vibration stimulation continuously is 10 seconds. After
10 seconds, the Remote Transmitter will “time-out” for 5 seconds and the
button must be released and pressed again. Tone stimulation will be delivered
as long as a Tone button is pressed.
What do I do if my dog’s neck
becomes red and irritated?
This condition is due to the Contact Points irritating the skin. Discontinue
use of the Collar Receiver for a few days. If the condition persists beyond 48
hours, see your veterinarian. Once the skin returns to normal, resume use and
monitor the skin condition closely.
The Intensity Dial seems
difficult to rotate. Is
this normal?
Yes. This prevents accidental changes in intensity and encourages an optimal
waterproof seal. The knob will “break in” and be slightly easier to turn as
you use it.
Can I attach a lead to the
Collar Receiver?
DO NOT attach a lead to the Collar Receiver. You may put a separate non-
metallic collar on your dog’s neck and attach a lead. Be sure the extra collar
does not interfere with the Contact Points.
Can I program my
SportTrainer®SD-825E
Remote Trainer to work
with my other SportDOG®
Brand systems?
Yes. You can program your SportTrainer®SD-825E Remote Trainers to work
with SD-425CAMO-E, SD-825E, SD-1225E, SD-1525E, SD-1825E, or SD-1875E
systems. Because the SD-825E operates at a different frequency, it is not
backwards compatible with any other SportDOG®Brand systems.
My Remote Transmitter is
sending a signal to more
than one Collar Receiver
unintentionally, what
should I do?
In the rare event this occurs, you can change your Remote Transmitter’s
ID Code. See the “CHANGE ID CODES” section to solve this issue.

18 SPORTDOG.COM
TROUBLESHOOTING
The answers to these questions should help you solve any problem you have with this system. If they do not,
please contact the Customer Care Centre or visit our website at www.sportdog.com.
My dog is not responding
when I press a button.
• Check to see if the Collar Receiver has been turned on and the Indicator Light
is flashing.
• If your range has reduced from the first time you used it, please check to see
if the battery is low in either the Remote Transmitter or Collar Receiver.
• Many factors can impact the range you have with the Remote Trainer. For a
list of these factors, please refer to “HOW THE SYSTEM WORKS”.
• You can verify the Collar Receiver is delivering static stimulation to your dog
by placing the Test Light Tool, enclosed in your kit, on the Collar Receiver.
Please refer to the “TEST LIGHT TOOL INSTRUCTIONS” section for details.
• Increase the Intensity Dial. Refer to “FIND THE BEST INTENSITY LEVEL FOR
YOUR DOG” for more information.
• Increase the Static Stimulation Range. Refer to “CHANGE STATIC
STIMULATION RANGES” for more information.
• Make sure the Collar Receiver’s Contact Points are placed snugly against
your dog’s skin. Refer to “FIT THE COLLAR RECEIVER” for more information.
• You may need to switch to the longer Contact Points included with your
system or trim the hair beneath the Contact Points.
• If you notice your operating time is significantly reduced from the original
time, your Collar Receiver battery needs to be replaced. Contact the
Customer Care Centre to purchase a new one.
The Collar Receiver will
not turn on.
• Make sure the Collar Receiver has been charged. The Collar Receiver will
charge in 2 hours.
The Collar Receiver is
not responding to the
Remote Transmitter.
• Make sure the Remote Transmitter has been charged. The Remote
Transmitter will charge in 2 hours.
• Verify the Collar Receiver has been turned on and the Indicator Light is
flashing. Refer to “TO TURN THE COLLAR RECEIVER ON”.
• Refer to “MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER”.
TEST LIGHT TOOL INSTRUCTIONS
1. Turn the Collar Receiver on.
2. Hold the Test Light Tool contacts to the Contact Points.
3. Press a Static Stimulation Button on the Remote Transmitter.
4. The Test Light will flash.
NOTE: At higher Static Stimulation Levels, the Test Light will flash brighter.
5. Turn the Collar Receiver off.
Save the Test Light Tool for future testing.
NOTE: If the Test Light does not flash, recharge the battery and re-test. If the
Test Light still does not flash, contact the Customer Care Centre.

19 SPORTDOG.COM
TERMS OF USE AND LIMITATION OF LIABILITY
1. TERMS OF USE
Use of this Product is subject to your acceptance without modification of the terms, conditions and notices
contained herein. Use of this Product implies acceptance of all such terms, conditions and notices. If you do
not wish to accept these terms, conditions, and notices, please return the Product, unused, in its original
packaging and at your own cost and risk to the relevant Customer Care Centre together with proof of
purchase for a full refund.
2. PROPER USE
This Product is designed for use with dogs where training is desired. The specific temperament or size/
weight of your dog may not be suitable for this Product (please refer to “HOW THE SYSTEM WORKS” in
this Operating Guide). Radio Systems Corporation recommends that this Product is not used if your dog is
aggressive and accepts no liability for determining suitability in individual cases. If you are unsure whether
this Product is appropriate for your dog, please consult your veterinarian or certified trainer prior to
use. Proper use includes, without limitation, reviewing the entire Operating Guide and any specific safety
information statement.
3. NO UNLAWFUL OR PROHIBITED USE
This Product is designed for use with dogs only. This dog training device is not intended to harm, injure
or provoke. Using this Product in a way that is not intended could result in violation of Federal, State or
local laws.
4. LIMITATION OF LIABILITY
In no event shall Radio Systems Corporation or any of its associated companies be liable for (i) any indirect,
punitive, incidental, special or consequential damage and/or (ii) any loss or damages whatsoever arising out
of or connected with the misuse of this Product. The Purchaser assumes all risks and liability from the use of
this Product to the fullest extent permissible by law.
5. MODIFICATION OF TERMS AND CONDITIONS
Radio Systems Corporation reserves the right to change the terms, conditions and notices governing this
Product from time to time. If such changes have been notified to you prior to your use of this Product, they
shall be binding on you as if incorporated herein.
COMPLIANCE
This equipment has been tested and found to comply with relevant R&TTE Directives. Before using this equipment
outside the EU countries, check with the relevant local R&TTE authority. Unauthorized changes or modifications
to the equipment that are not approved by Radio Systems Corporation are in violation of EU R&TTE regulations,
could void the user’s authority to operate the equipment, and void the warranty.
The Declaration of Conformity can be found at: www.sportdog.com/eu_docs.php.
IC
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This device has been designed to operate with the antennas provided with the equipment. Use of other antennas
may violate Industry Canada rules and void the user’s authority to operate the equipment.
ACMA
This device complies with the applicable EMC requirements specified by the ACMA (Australian Communications
and Media Authority).

20 SPORTDOG.COM
BATTERY DISPOSAL
See Important Safety Information on page 3 related to the battery.
This system operates on two Li-Ion battery packs (160mAh capacity for the Collar Receiver, 200mAh capacity for
the Remote Transmitter). Only replace with battery received from calling the Customer Care Centre. For a listing
of the telephone numbers in your area, visit our website at www.sportdog.com.
Separate collection of spent batteries is required in many regions; check the regulations in your area before
discarding spent batteries. Please see below for instructions on how to remove the battery from the product for
separate disposal.
AT END OF PRODUCT LIFE, USE THESE BATTERY REMOVAL INSTRUCTIONS FOR FINAL DISPOSAL (DO NOT
OPEN THE COLLAR RECEIVER OR REMOTE TRANSMITTER UNTIL YOU HAVE RECEIVED THE REPLACEMENT).
• Using a Number 1 Phillips screwdriver, remove the case screws from your Remote Transmitter.
• Using a 3/32 Allen Wrench, remove the case screws from your Collar Receiver.
• Remove the case back or cover.
• Remove the old battery pack.
• When removing the old battery pack, care must be taken when gripping the connector firmly to avoid
damaging the wires. Shorting the battery wires may cause fire or explosion.
• These instructions are not valid for repair or battery replacement. Replacing the battery with a battery
not specifically approved by Radio Systems Corporation may cause fire or explosion. Please call the
Customer Care Centre to avoid invalidating your warranty.
IMPORTANT RECYCLING ADVICE
Please respect the Waste Electrical and Electronic Equipment regulations in your country. This equipment
must be recycled. If you no longer require this equipment, do not place it in the normal municipal waste system.
Please return it to where it was purchased in order that it can be placed in our recycling system. If this is not
possible, please contact the Customer Care Centre for further information. For a listing of Customer Care Centre
telephone numbers, visit our website at www.sportdog.com.