SportsArt Fitness CardioActive T672 User manual

Sports Art Industrial Co., Ltd. TUV-CERT ISO 9001/9002/14000 Certied Quality Products 2013.07.23 US
T672 Treadmill
Owner’s Manual

T672 OWNER’S MANUAL CONTENTS
1. INTRODUCTION ................................................................................ 2
2. SAFETY PRECAUTIONS .................................................................. 3
3. LIST OF PARTS ................................................................................. 5
4. ASSEMBLE THE PRODUCT ............................................................. 7
STEP 0 Preparation: Inspect the Walk Belt Placement ......................... 7
STEP 1 Install the Pedestals and Cowling ............................................ 8
STEP 2 Install the Display ..................................................................... 13
STEP 3 Move the Treadmill into Place for Use ...................................... 15
STEP 4 Level the Treadmill ................................................................... 16
STEP 5 Align the Walk Belt ................................................................... 16
STEP 6 Adjust the Walk Belt Tension .................................................... 17
STEP 7 Install the Power Cord .............................................................. 17
5. UNDERSTAND THE T672 DISPLAY ................................................. 19
DISPLAY Overview ................................................................................ 19
DISPLAY Windows ................................................................................ 19
DISPLAY Keys ....................................................................................... 20
DISPLAY Safety Key ............................................................................. 21
6. OPERATE THE T672 TREADMILL ................................................... 22
OPERATION QUICK START Key........................................................... 22
OPERATION START Key ...................................................................... 22
OPERATION Workout Program Operation ............................................ 22
OPERATION During the Workout ......................................................... 24
OPERATION Cool Down ....................................................................... 25
OPERATION Workout Program Details ................................................. 25
OPERATION Basic Settings .................................................................. 29
OPERATION Time Limit Setting ............................................................ 30
OPERATION Error Messages ................................................................ 30
7. ABOUT HEART RATE DETECTION .................................................. 32
HEART RATE Telemetry ........................................................................ 32
HEART RATE Contact ........................................................................... 32
8. GUIDELINES FOR EXERCISE ......................................................... 33
9. MAINTENANCE ................................................................................ 34
MAINTENANCE How to Replace a Fuse ............................................... 34
MAINTENANCE Walk Belt Lubrication .................................................. 35
MAINTENANCE Schedule ..................................................................... 37
MAINTENANCE Task List ..................................................................... 38
MAINTENANCE One-Year Maintenance Log ........................................ 39
MAINTENANCE Electronics Block Diagram .......................................... 40
10. CONSIGNES DE SÉCURITÉ IMPORTANTES ............................... 41

2
1. INTRODUCTION
Congratulations on the purchase of a high quality SportsArt product, the T672
treadmill. Constructed of high quality materials and designed for years of reliable
performance, this product was made for full commercial use.
Before this product is assembled or operated, we recommend that you familiarize
yourself with this manual. Understanding the correct assembly and operation of
this product will help ensure that exercisers obtain their tness goals safely and
successfully.

3
2. SAFETY PRECAUTIONS
This product was designed and built for optimum safety. However certain precau-
tions apply during the use of this product. Please note the following safety
precautions:
• Please read the entire manual before assembly and operation. Make
sure the product is installed and operated as instructed in this manual.
• Assemble and operate the product on a solid, level surface. Do not use
outdoors or near water, including pools and saunas.
• Check the product before every use. Make sure all parts are assem-
bled, and all fasteners are tightened. Do not use the product if it is disas-
sembled in any way.
• Wear proper workout clothing. Do not wear loose clothing. Do not wear
shoes with leather soles or high heels. Tie all long hair back. Do not go
barefoot on this product.
• Keep away from moving parts. Moving parts may or may not stop imme-
diately if an object becomes caught or impedes normal motion.
• Use this product only for its intended purpose as described in this
manual.
• Be careful when mounting and dismounting the unit.
• Never operate this product if it has been damaged in any way. If it is
not working properly, or has been dropped or damaged, contact a service
technician for repairs.
• Do not use accessories that are not specically recommended by the
manufacturer. Such parts might cause injuries or cause the unit to fail.
• Keep all air ventilation areas free of blockage. Never drop or insert any
object into any opening.
• Do not operate where aerosol (spray) products are being used or where
oxygen is being administered.
• This product is not intended for use by persons (including children) with
reduced physical, sensory, or mental capabilities, or by people who are
otherwise decient in product knowlege or experience. If such people use
this product, they should be given training and be supervised at all times
by someone responsible for their safety.
• Children should be supervised to ensure that they do not play on or
near the product.
• Treadmills should be positioned awayfrom walls to avoid injury due to
falls. Be sure that the back of the treadmill has at least six to seven feet of
clearance from a ledge, wall or window. The power supply and wiring should
be located away from walking paths or taped to prevent tripping when step-
ping on or off of the running belt.
• The user weight limit for this product is 227 kg, 500 lb. At maximum
speed, this product meets standards for users up to 180 kg, 400 lb.

4
2. SAFETY PRECAUTIONS (CONTINUED)
CAUTION: If you feel any pain or any abnormal sensations, STOP YOUR
WORKOUT and consult your physician immediately. Work within your
recommended exercise level. DO NOT work to exhaustion. Before beginning
any exercise program, you should consult with your doctor. It is recommended that
you undergo a complete physical examination.
WARNING! Heart rate monitoring systems may be inaccurate. Too much exercise
may result in serious injury or death. If you feel faint, stop exercising immediately.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If the user desires to correct the
interference, it is at the user’s own expense.
WARNING! Only qualied technicians should be allowed to contact electrical
components such as circuit boards. Some components carry an electrical charge
even after use has been discontinued or the product has been unplugged. For
products with power cords, turn off unit power, wait ve minutes, then disconnect
the power cord from the power socket. For products without power cords, let the unit
sit without use for ve minutes. Only after taking such precautions should covers be
removed and electrical components be accessed.
• Do not attempt to drag or carry this unit by the power cord. Keep the
power cord away from heated surfaces.
• Improper grounding can increase the risk of electric shock. Check with
a qualied electrician if you are in doubt as to whether the power outlet is
properly grounded.
• Do not attempt to modify the plug provided with this product. Proper pow-
er supply must be provided. If the plug does not t an outlet, contact a quali-
ed electrician to inspect or modify power in the facility.
• Do not stand on the walk belt
when starting the treadmill. Strad-
dle the belt with your feet on the
right and left landing strips.
• Always use the safety key
when operating the treadmill.
French speakers, please note the
following:
• Please place the sticker (pro-
vided in the owner’s manual) on
the product as shown.
• Please note safety precau-
tions in French in chapter 10.

5
3. LIST OF PARTS
Assembly Parts
No. Name Qty. No. Name Qty.
A1 Display 1 A5 Left pedestal 1
A2 Cowling with handles 1 A6 Water guard 1
Safety key 1 A7 Feeder cord 1
A2a Right cup holder 1 A8 Owner’s manual 1
A2b Left cup holder 1 A9 Hardware kit 1
A3 Right pedestal 1 A10 Power cord 1
A4 Body 1 A11 Lubrication kit - applicator tube 1
A4a Motor right cover 1 Silicone lubricant 1
A4b Motor left cover 1 1

6
Components in the Hardware Kit
No. Name Qty. Specication Notes
21 Adapter 1
Fuse (Europe, etc.) 1 10A-200V-240V
Fuse (N. America) 1 15A-100V-110V
T-shaped Allen wrench 2 M4
T-shaped Allen wrench 1 M6
L-shaped Allen wrench 2 M6
Double open-end wrench 1 22*24
Cable wrench 1
Screwdriver handle 1 green
Screwdriver shank 1 Phillips and at
Components on the Product
No. Name Specication Notes
41 Phillips screw M5*L10
42 Inner hex screw M8*L18
Spring washer M8
Serrated washer D18*d8.5*t2
43 Inner hex screw M8*L15
Flat washer D17*d8.3*t2
44 Mushroom top Phillips screw M5*L12
45 Mushroom top inner hex screw M6*L12
Flat washer D13*d6*t2
46 Phillips screw M4*L8

7
4. ASSEMBLE THE PRODUCT
Follow instructions below to assemble this product. Note that in this manual
the words “left” and “right” are used to refer to the product and its parts. As
such, these designations correspond to the “left” and “right” sides of a person
in position to exercise on this product. Also, for brevity, the word “screws” is
used where screws, washers, and other hardware may be involved. And, for
clarity, names of keys are capitalized.
STEP 0 Preparation: Inspect Walk Belt Placement
Inspect the position of the walk belt in relation to the guide rollers. The guide
rollers should press the walk belt down, away from the body of the treadmill
(image √). Make sure that the walk belt is not in between the guide rollers
and the deck (image X). As such, the guide rollers would press the walk belt
upward, toward the body of the treadmill.
If the walk belt is in the wrong position, rotate rear roller adjustment screws
(A) counterclockwise to loosen the walk belt. Then flip the walk belt so it is
beneath the guide rollers. After making sure the walk belt is in the correct
position, adjust walk belt tension as shown in step 8.
Note: If installing with the optional intergrated TV, it is recommended to read
the T672 CES installation guide before proceeding.
A

8
STEP 1 Install the Pedestals and Cowling
Follow instructions below to install the pedestals and cowling. The illustration
below provides an overview of this step.
STEP 1 Install the Pedestals and Cowling (Continued)
(a) First, remove screws
(41) from motor left/right
side covers (A4a,A4b).
Then remove those
covers (A4a,A4b).
(b) Next, remove screws
(42) from the pedestal
mounts.
(b)
(a)

9
STEP 1 Install the Pedestals and Cowling (Continued)
Follow instructions (a through e) below to thread the data cable through the
right pedestal.
(a) Cut the zip tie on the data cable,
and pull the cable end away from the
pedestal mount as shown.
(b) Place the right pedestal (A3) on
the floor as shown, with the bottom
end facing the data cable. Detach the
feeder cord (A7) from the base of the
pedestal. Then tie the low end of the
feeder cord onto the top of the data
cable.
(c) Disconnect the feeder cord (A7) at
the top of the right pedestal (A3).
(d) From the top of the pedestal, pull
the feeder cord (A7), thus threading
the data cable through the right ped-
estal (A3).
(e) Once the data cable has been
threaded through the pedestal, untie
the feeder cord (A7) from the data cable.
Note: If installing with the optional intergrated TV, also feed the TV connec-
tion cable through the pedestal.
STEP 1 Install the Pedestals and Cowling (Continued)
While holding the data cable to prevent it from slipping into the pedestal, lift the
top of the right pedestal (A3). Then insert the pedestal base onto its mount.
Use screws (42) to
loosely secure the
right pedestal (A3)
into place. Avoid
pinching or crimping
the data cable, and
prevent it from fall-
ing into the pedestal.
Use screws (42) to
loosely secure the
left pedestal (A5)
onto its mount. Do
not fully secure ped-
estal screws yet. To
make motor cover
assembly easy, slide
the water guard up-
ward, above the mo-
tor cover.

10
STEP 1 Install the Pedestals and Cowling (Continued)
(a) Remove screws (43) from the top
of the left and right pedestals.
(b) Then remove screws (44) and
bottle holders (A2a, A2b) from the
cowling (A2).
STEP 1 Install the Pedestals and Cowling (Continued)
Install the cowling and route the data cable as shown in instructions (a
through e) below.

11
STEP 1 Install the Pedestals and Cowling (Continued)
(a) First, set the left
side of the cowling
(A2) onto the left
pedestal (A5).
(b) Insert the data
cable from the right
pedestal (A3) into
the square hole in
the right side of the
right pedestal (A2).
Then thread the
cable out the hole
in the bottle holder
as shown.
Note: If installing
with the optional in-
tergrated TV, refer
back to T672 CES
installtion manual
before proceeding
to next step.
STEP 1 Install the Pedestals and Cowling (Continued)
(c) Set the right side
of the cowling (A2)
onto the right pedes-
tal (A3).
(d) Insert the end of
the data cable into the
square hole in the left
side of the right bottle
holder.
(e) Thread the end of
the data cable out the
front of the cowling
(A2).
(a)
L
R
R L
R L
(b)

12
STEP 1 Install the Pedestals and Cowling (Continued)
After securing the cowling, secure screws (42) onto the base of left and right
pedestals (area A). Put motor right and left side covers into place, and se-
cure them with screws (41). Then slide the water guard (A6) downward into
place against the motor cover.
STEP 1 Install the Pedestals and Cowling (Continued)
(a) After routing the data cable, se-
cure the cowling by fastening screws
(43) into the upper part of the left and
right pedestals.
(b) Set bottle holders (A2a,A2b) into
place, then use screws (44) to secure
them into place.
Note: If installing with the optional
intergrated TV, the left cup holder
(A2b) does not lock back. Refer back
to T672 CES installation manual step
4 to 7.
(a)
(b)
A
B

13
STEP 2 Install the Display
Follow instructions below to install the display onto the cowling. The illustra-
tion below provides an overview of this step.
STEP 2 Install the Display (Continued)
Please follow steps (a
through c) to install the
display cables.
(a) First, remove
screws (45) from the
cowling (A2).
(b) Place the display
(A1) onto the upper
part of the cowling
(A2) horizontally.

14
STEP 2 Install the Display (Continued)
After securing cable connections, follow steps (a) through (d) below to secure
the display (A1) into
place.
(a) Rotate the dis-
play (A1) upward,
aligning holes in
its support piece to
hooks in the cowl-
ing, fitting the dis-
play into place on
the cowling (A2).
(b) Make sure that
the display cov-
er clicks into the
cowling as shown.
Press downward
on the display (A1)
to secure it at the
correct angle.
STEP 2 Install the Display (Continued)
(c) Connect cables
in area A. Then
connect cables in
area B.
B
A
(C)
(a)
(b)

15
STEP 2 Install the Display (Continued)
(c) At this point, inspect the lower
cover on the display (A1). It must
rest on the outside of the cowl-
ing (A2). If it is on the inside of
the cowling, please lift the display
(A1) slightly, and reinstall it into the
cowling (A2).
(d) Finally, use screws (45) to se-
cure the display.
STEP 3 Move the Treadmill into Place for Use
Grip the frame in area A as shown,
lift, and roll the treadmill into place.
A

16
STEP 5 Align the Walk Belt
There should be an equal amount of space on both sides of the walk belt. If
there is more space on one side than the other, please align the walk belt as
follows. On the side with less space between the walk belt and the landing
strip, turn the rear
roller adjustment
screw clockwise
one quarter ro-
tation, and let
the walk belt run
slowly. This will
force the walk
belt toward the
other side of the
treadmill. Make
adjustments as
needed, but avoid
turning rear roller
screws more than
one quarter rota-
tion at a time.
STEP 4 Level the Treadmill
Press downward on the rear part of the treadmill as shown. Inspect whether
the treadmill rests
flat on the floor. If
the treadmill wob-
bles, please ad-
just treadmill lev-
elers as follows:
a. Loosen the lev-
eler nut.
b. Rotate the lev-
eler foot down-
ward, touching
the floor.
c. Rotate the lev-
eler nut upward,
against the frame
of the product, to
secure this posi-
tion.
abc

17
STEP 6 Adjust Walk Belt Tension
Walk belt tension is important to treadmill performance. As your foot hits the
walk belt, does the walk belt stop sluggishly before regaining traction? Or, if
you stomp your feet, bracing against the direction of rotation, does the walk
belt not pause whatsoever? When either of these two conditions occurs,
walk belt tension should be adjusted. To further examine walk belt tension,
lift both sides of the walk belt at the center of its length. The walk belt should
rise 30 mm (about 1 1/8th
inch). A hanging gauge,
should measure the weight
at 3 kg or 6.6 lb.
Adjust the tension if it dif-
fers from this specification.
If the walk belt is too loose,
use a hex wrench to turn
rear roller screws clock-
wise one quarter rotation
at a time. If the walk belt is
too tight, use a hex wrench
to turn rear roller screws
counterclockwise one half
rotation at a time. Test walk
belt tension after each ad-
justment.
STEP 7 Install the Power Cord
First remove screws (46) from the power cord socket on the product.
Insert the power cord into
place on the product. Se-
cure the power cord (A10)
connector screws (46).
And insert the other end
of the power cord into the
power socket on the wall.
To turn on the treadmill,
press the side of the power
switch with the “O” mark.
An LED in the switch will
light up, and the startup
banner screen, showing
“SPORTSART T672”, will
appear on the display.

18
If installing with the optional intergrated TV, refer back to T672 CES install-
tion manual and also follow the instructions bellow.
(a) Thread the CES cable from the left pedestal (A5) to the left side cowling
(A2).
(b) Attach the whole cowling assembly (A2) onto both pedestals (A5).
Note: Make sure the cables are not exposed.

19
5. UNDERSTAND THE T672 DISPLAY
DISPLAY Overview
The T672 display was designed to help people obtain their fitness goals
simply and conveniently. Please familiarize yourself with the features of this
display and thereby get optimum benefit and enjoyment from this product.
Cardio
target
heart rate
Weight
loss target
heart rate
Percent of
workout
completed Message
window
Message
row control
Dot matrix/
workout
illustration
Heart rate
indicator
Lower
keypad
Actual
heart rate
Numeric
keys
DISPLAY Windows
SPEED (forward rotation): 0.2 to 24.0 kph; 0.1 to 15.0 mph
INCLINE: 0% to 15%, in intervals of 0.5%
TIME: 0:00 to 99:59
DISTANCE: 0.00 to 9999 kilometers or miles
CALORIES: Range 0 to 9999 kcal
CAL/HR: 0 to 9999 kcal
METS: Metabolic equivalent of task: 0.0 to 99.0
PACE: 1 / SPEED
Note: VOL keys
are for iPod
volume control.
Workout
program
keys