Spraying Systems AutoJet 1000+ User manual

Scan the QR code, or visit spray.com/autojetspraycontrol, to access
manuals, videos and additional resources on the AutoJet®1000+ control panel.
AUTOJET®1000+ SPRAY CONTROL PANEL
QUICK START GUIDE
Each user’s setup will be different and may or may not include all the connections or features that are listed.
See owner’s manual for more information on connections.

2.
CONNECT ELECTRIC
SPRAY NOZZLE
Connect the electric spray nozzles to OUT A or OUT
B/ATOM connections on the control panel. If multiple
nozzles, connect nozzles to a junction block and then
connect the junction cable to a OUT A or OUT B/ATOM.
(Connect up to 8 electric spray nozzles using the
junction block, note if using both channels the total for
both cannot exceed 8).
For additional connections see step 3
Junction Block
1.
MOUNT
THE PANEL
If mounting on a wall use anchors that are designed
to support at least 15 lbs. (6.8 kg), according to the
anchor manufacturer’s specifications. If mounting to an
AutoJet®system use provided hardware. The mounting holes
are on 5.44" (138 mm) x 10.72" (272 mm) centers
and are made for 1/4" (6 mm) screws with 3/8" (10 mm)
diameter screw heads.
1000+ Spray Control
5.44" (138 mm)
8.00" (203.2 mm)
0.27"
(6.8 mm)
10.72"
(272 mm)
11.34"
(288.1 mm)
0.83" (21 mm)
Typ. 4 places
1000+
SPRAY CONTROL PANEL
FLOAT A
FLOAT B
INPUT
100-240V
50/60hZ 3A
TRIG A
TRIG B
OUT A
OUT B/ATOM

1000+
SPRAY CONTROL PANEL
FLOAT ATRIG A
TRIG B
OUT A
OUT B/ATOM FLOAT B
INPUT
100-240V
50/60hZ 3A
3. ADDITIONAL CONNECTIONS IF APPLICABLE
1. TRIGGER OR SENSOR
Connect trigger or sensor devices to the TRIG A and
TRIG B connections that will be used to start spray
sequence. Available triggers are as follows, the one
used should be based on the customer’s application.
• Trigger cable (for use with customer-supplied
trigger signal)
• Sensors including:
– Object
– Proximity
– Laser (short/long)
– Thru-beam
– Full spectrum color sensor
• Hand-held trigger unit
• Foot switch
2. FAN/ATOMIZING AIR
Fan/Atm Air electrical connection is used to actuate
the air solenoids in our control panel. Connect the
cable from the air control panel to OUT B/ATOM
connection on the panel.
3. FLOAT SWITCH
Connect float switch cables to FLOAT A and/or FLOAT B.
When the tank is low, an alert is displayed on the control
panel HMI and the green system status LED flashes.
2 31

1000+
SPRAY CONTROL PANEL
FLOAT A
FLOAT B
INPUT
100-240V
50/60hZ 3A
TRIG A
TRIG B
OUT A
OUT B/ATOM
4.
POWER UP
THE PANEL
Plug into grounded 100/240VAC, 3A, single phase GFCI
outlet. Turn power on. HMI display will illuminate.
To set spray parameters and for HMI operation, please
refer to the Application Settings in the owner’s manual.
5.
CONFIGURE
SETTINGS
Set Spray Configuration:
Set the start delay, spray period, and desired timing mode
for each channel that will be used. Timing modes include
variable, repeat, and fixed spray.
Set Recipe Configuration (OPTIONAL):
If you have recipe configuration, it will allow you to select
the recipe number, create a name, select a desired timing
mode, set the start and stop delay and set the interval on
and off.
Recipe #
Start delay (s)
Stop delay (s)
SPRAY CONFIGURATION
Timing Mode:
Screen Capture to .jpg
Air Atomizing Settings
A B
5.00
8.00
Fixed Spray
Recipe #
Recipe name
Start delay (s)
Stop delay (s)
RECIPE CONFIGURATION
Timing Mode:
1
0.01
0.01
Fixed Spray
Screen Capture to .jpg
Air Atomizing Settings

PN: ML001000CONQS Rev. 041322
North Avenue and Schmale Road, P.O. Box 7900, Wheaton, IL 60187-7901 USA
Tel: 1.800.95.SPRAY Intl. Tel: [phone]
Fax: 1.888.95.SPRAY Intl. Fax: [phone]
Email: [e-mail]
www.spray.com
© 2022 Spraying Systems Co. All rights reserved.