Spraying Systems AutoJet 1750+ User manual

AUTOJET®1750+ SPRAY CONTROL PANEL
QUICK START GUIDE
Scan the QR code, or visit spray.com/autojetspraycontrol, to access manuals,
videos and additional resources on the AutoJet 1750+ Spray Control Panel.
Each user’s setup will be different and may or may not include all the connections or features that are listed.
See owner’s manual for more information on connections.

1.
MOUNT
THE PANEL
If mounting on a wall use anchors that are designed to
support at least 15 lbs. (6.8 kg), according to the anchor
manufacturer’s specifications. If mounting to an AutoJet®
system use provided hardware. The mounting holes are on
5.44" (138 mm) x 10.72" (272 mm) centers and are made for
1/4" (6 mm) screws with 3/8" (10 mm) diameter screw heads.
1750+ Spray Control
5.44" (138 mm)
8.00" (203.2 mm)
0.27"
(6.8 mm)
10.72"
(272 mm)
11.34"
(288.1 mm)
0.83" (21 mm)
Typ. 4 places
1750+
SPRAY CONTROLLER
2.
CONNECT ELECTRIC
SPRAY NOZZLES
Connect spray nozzle cable to the Main connection.
For multiple nozzles, connect nozzles to a junction block
and then connect the junction block cable to a Main
connection. (Connect up to 10 electric spray nozzles
using the junction block)
For additional connections see step 3
Junction Block

1750+
SPRAY CONTROLLER
3. ADDITIONAL CONNECTIONS IF APPLICABLE
1. REMOTE DUTY CYCLE
Connect Remote Duty Cycle cable to 4-20mA
connection on the panel. Once the unit is powered
up on the HMI you can set the duty cycle with
a 4-20mA signal to control the spray nozzles
cycle speed.
2. TRIGGER OR SENSOR
Connect cable to Trig connection that will be
used to start spray sequence. Available triggers
are as follows, the one used should be based
on the customer’s application.
•Trigger cable (for use with customer-supplied
trigger signal)
•Sensors including:
– Object
– Proximity
– Laser (short/long)
– Thru-beam
– Full spectrum color sensor
•Hand-held trigger unit
•Foot switch
3. AUX = NOZZLE AIR ON/OFF
The Aux/Nozzle Air electrical connection is used to actu-
ate the air solenoids in our air control panel. Connect the
cable from the air control panel to Aux/Nozzle Air connec-
tion on the panel.
4. TRIGGER INTERLOCK
Trigger Interlock controls the state of run/standby
mode. Connect the trigger interlock cable to the
T. int. connection on the panel.
23 41

1750+
SPRAY CONTROLLER
4.
POWER UP
THE PANEL
Plug into grounded 100/240VAC, 3A, single phase GFCI
outlet. Turn power on. HMI display will illuminate.
To set spray parameters and for HMI operation, please
refer to the Application Settings in the owner’s manual.
5.
DOWNLOAD THE SMART
DEVICE CONNECTION
1.Go to the Google® Play Store or Apple® App store and download
a VNC viewer app, such as VNC® Viewer from RealVNC®.
2.In Wi-Fi settings on your mobile device, locate the Wi-Fi SSID,
typically SSCO_xxxxxx. Select connect and enter the default
password of SSCO1750.
Note: There is a chance that your network administrator blocks
this type of connection.
3. Open VNC Viewer and connect to the 1750+
at: 192.168.0.20:5900.
HMI display
1
2
3

PN: ML001750CONQS Revised 04/13/22
North Avenue and Schmale Road, P.O. Box 7900, Wheaton, IL 60187-7901 USA
Tel: 1.800.95.SPRAY Intl. Tel: [phone]
Fax: 1.888.95.SPRAY Intl. Fax: [phone]
Email: [e-mail]
www.spray.com
© 2022 Spraying Systems Co. All rights reserved.