Spypoint FORCE-10 Troubleshooting guide

QUICK START GUIDE
v1.8
FORCE-10
& COMPARABLES*

2 3
ENGLISH
ENGLISH
In the box
Components
Note: Memory card and batteries are sold separately.
OK button
Navigation buttons
 Congurationscreen
SD card slot
Photo lens
Test light
Cable lock hole
Detection lens
12V Jack
BUSY LED
Battery case
Slot for installation strap
Tripod mount
LEDs
1
2
3
4
5
6
7
8
9
10
11
12
13
14
* Specs and features may dier across comparable models. Refer to website or
packaging for full details.
1x Camera
1x Mounting brackets
1x Installation strap
1x Quick start guide 1
4
2
3
5
68
9
7
14
12
11
13
User manual, latest rmware & FAQ available at:
www.support.spypoint.com
10

4 5
ENGLISH
ENGLISH
REMOVE THE CAMERA FROM THE MOUNTING BRACKET
• Push the tab to release the camera from the mounting bracket.
• Remove the camera.
CHOOSE A POWER SOURCE
Observe the proper battery polarity orientation according
to the (+) and (-) marks when installing AA batteries.
To ensure maximum performance of the camera and prevent battery
leak, we recommend the use of new batteries. Do not mix old and new
batteries together or mix battery type . Use ALL alkaline or ALL lithium.
Rechargeable AA batteries are not recommended as the lower vol-
tage they produce can cause operational issues.
Getting started
RECHARGEABLE 7.4 VOLT LI-ION POLYMER BATTERY 2.0 Ah
RECYCLE OR DISPOSE OF PROPERLY
Li-ion Madein China |Fabriqué en Chine v2.3
www.spypoint.com
P INTSPY INTPSPY
Models: LIT-09:Battery only LIT-C-8:LIT-09 Battery & charger WARNING:To reduce risk of fire or burns, - Do not attempt to open, disassemble, or service the battery pack. - Do not crush, puncture, short external contacts, or dispose of in fire or water.
ATTENTION:Pour réduire les risques de feu ou de brûlures, - Ne pas essayer d’ouvrir, désassembler,ou de réparer la pile. - Ne pas frapper, percer,court-circuiter les contacts externes de la pile ou mettre dans le feu ni l’eau.
6 alkaline or lithium
AA batteries
Lithium battery pack
LIT-09/LIT-C-8
DC 12V
12V power
source
INSERT THE MEMORY CARD
Insert an SD/SDHC memory card (up to 32 GB capacity) in the card
slot with the label side facing upward. The card is inserted correctly
when a click is heard. Always ensure that the camera power is OFF
before inserting an SD card.
We suggest to format your SD card if it's been in another
electronic device.


6 7
ENGLISH
ENGLISH
Use the and  buttons to navigate in the interface and to change
options. Use the OK button to conrm and the BACK button to
return to the previous menu.
GENERAL SETTINGS
A. To turn ON/OFF the camera, press and hold the OK button.
B. In the home menu, select SETTINGS and then GENERAL to
access to the General settings menu.
C. Set the Date (MM/DD/YY or DD/MM/YY).
D. Set the Time (Hour/Minute).
E. Set the Night mode (Best option for photos)
Settings
illumination modes comparison* (Night modes)
* Available for photos only
optimal
MODE
IR-boost
MODE
Blur reduction
Battery life
Flash range

 




CONFIGURE THE SETTINGS OF THE 3 OPERATING MODES
In the home menu, select SETTINGS and then, PHOTO, TIME
LAPSE or VIDEO to access to the respective operating mode
menu.
PHOTO
Delay: Allows the user to choose the time interval between each
detection before the camera can record the next photo.
Multi-shot: Takes up to 6 consecutive shots at each detection,
with a 5 second delay between each photo.
TIME LAPSE
Interval: This option allows the camera to take photos at regular
preset intervals without detection.
VIDEO
Delay: Allows the user to choose the time interval between each
detection before the camera can record the next video.
Video length: Allows the user to select the duration of the
recording.
Photo rst: When this option is enabled, a photo is taken
immediately before each video.
(Conguration)
Photo
(Conguration)
Time lapse
(Conguration)
Vidéo
HOME
SETTINGS
Start Camera
Detection test
Settings
Photo
Time lapse
Video
General
(Conguration)
Photo
(Conguration)
Time lapse
(Conguration)
Vidéo
(Conguration)
Général
HOME
SETTINGS
Start Camera
Detection test
Settings
Photo
Time lapse
Video
General

8 9
ENGLISH
ENGLISH
When installed with the mounting bracket, the camera can be re-
moved to access the battery case without affecting the installation.
Recommended installation height:
The camera should be installed at the same height as the animal’s
mid-body.
Ideal installation for quality pictures & videos:
The targeted animal should be 25 feet / 7.5m away from the camera
forabettereldofview.
To get brighter pictures at night , you should have elements in the
backgroundtoreectbacktheIRashtothecamera.
Note that the camera should not directly be facing the sun to avoid
back lighting and false detection.
or
Installation & Mounting bracket
RECOMMENDED SETTINGS IN PHOTO MODE
Usage in trails Usage by a feeder
Delay Instant 5 min
Multi-shot 1 1-3
CAMERA
CAMERA
CAMERA
CAMERA

10 11
ENGLISH
ENGLISH
FAQ, user manual & latest rmware available at:
www.support.spypoint.com
 Live Chat support at SPYPOINT.COM
 [e-mail]
Join the community
Sit back & relax as this SPYPOINT trail cameras is
covered by the “ Know you’re covered ” 2 year warranty.
We strive on offering all customers a positive, user
friendly experience that will have a lasting impression.
THANK YOU
for choosing
TEST THE DETECTION OF THE CAMERA
In DETECTION TEST mode, no photo
or video is recorded. Pass in front of
the camera from left to right. When
the camera detects motion, the test
light blinks. If the system does not
detect the movement, realign the
system differently.
START THE CAMERA
Select the desired operating mode (photo, time lapse or video) in
the mode menu by pressing OK.
When the mode is selected, the test light in front of the camera will
ashfor30secondstoallowtheusertoleavetheareawithoutbeing
photographed or recorded.


30 s
(Conguration)
Photo
(Conguration)
Time lapse
(Conguration)
Vidéo
HOME
MODE
Start Camera
Detection test
Settings
Photo
Time lapse
Video
HOME
Start Camera
Detection test
Settings