SSS Siedle HT 644-02 Installation manual

Electronic special departement
Siedle Multi
Programming
instruction
HT644-02
05.03
ex Vers. ES 04.5x

2
HT644-02
General information
This Programming Instruction is validfor units fromsoftware version ES 4.5x.
Olderunits fromsoftware version4.16 onwards can beupgraded through replacing the
EPROMat any time. Additionally, the D7 SMD-diode must be removed fromthe mainprinted-
circuit-board.
Programming isperformed step by step using both adisplay screen and the relatedcontrol
keys which controlthe dialog. Each entry must be confirmed.
Before starting programming, bothallsystemsubscribers must be connectedand the system
must be activated.
Desktopforprogramming
In addition to the display screen, the following keys are required:
Invokingthe programmingmenu
Take off the handset
Enter 0000
Enter password
8888
The particular menu items can be selected through
the
(forward) resp. (backward) keys.
Exitingthe programmingmenu
Press the key, or hang up the handset
Initializing
Employing one HT644... internal telephone, aninitialization must be executed before the
systemiscommissioned-up forinitialoperation.(please, refer to menu item12.01). Through
thisinitialization, allunits which are connected tothe systemare enteredand astatus
catalogue ofthe particularunits iscreated. Thestatuscatalogue isneeded tocommunicate
status informationto allunits,such asassignment of the corresponding subscribers to a
subscribergroupor functionality,etc.. Notuntilafter executing aninitialization, correct
switchingfunctions, using of group speech paths, and call redirections are possible.
After each upgrading of the system, or each modifying of functions, an initialization isrequired.
Infofunction
Unittype, software version, unit address, andthe assigned subscribernumber are shownin
the display screen through selectingthe ikey.
Forward Invokes either the nextmenu or the next submenu item.
Backward Invokes either the nextmenu or the next submenu item.
Exit Completes either the programming menu or a submenu.
Confirm Applies the entered values in the memory.
0 -9Data Input data, programming values, and decisionsmade (yes / no)
0000Pleasedial
####Codeword
Programmingmenu
< Back Forward>

Outline of menus
To commence programming
throught the
programming menu:
Lift handset
Enter "0000"
Enter the password(8888)
121
112
103
94
85
7*6
7* only incombination withMFM611-10
Programming menu
< back Forward>
Set clock
with<OK>
Change call no
assign. with<OK>
Pleasedial
Alarm & emerg.
menu with<OK>
Output 12 acti-
vatewith<OK>
SwitchLED 4
with<OK>
Areas / ft.
Enable/dis <OK>
Basic parameters
programming <OK>
TLP call menu
with<OK>
Coll. call menu
with<OK>
Call back menu
with<OK>
MFMprogram
with<OK>
Servicemenu
with<OK>

3
Programming-
instruction
Scheduleof ContentsPage
1Basicparameters
Setting-up the language (G, UK, F, NL, I)
Unit address, group no., speechcircuit enable, active/passive,
video mode, compatibility,
4
2Door-parallel-call menu
Receiving aglobal or local door-parallel call 8
3Collective-call menu
Authorization toreceive, authorization tosend, group-collectivecall 9
4Alarm-and-emergency-call menu
Processing bothalarm and emergency calls, firealarms 10
5Callback menu
Storing and showing internal background door calls 12
6Assigning subscriber numbers
Assigning subscriber numbers freely tosubscriber addresses 13
7∗Allocating MFM ∗
Allocating MFMkeys bothtofunctions and subscriber numbers 15
8Activating output 12
Activating the output incombination withvarious functions 18
9Switching LED 4
Allocating the LED tovarious functions 20
10 Areas/ functionsof Enable/ Disable
Enabling / disabling the desktop (key functions) 22
11 Setting thesystemclock
Showing the current clock, internal / external 24
12 Service menu
Initialisation, default settings, show datatransfer,
Selecting the video operating mode
25
Generalinformations
Documentation items 27
∗) is not possibleother than incombination withaMFM611-10 unit

4
HT644-02
1 Basic parameters menu
Setting of generalfunctions and options
⇒open menue with , or Continue with
.
1.01 Unit address
Each unit requires its ownlogic unitaddress.
Up to a maximumof 4 units can beoperated inparallel under
the same address.
⇒Enterunit address (1 – 254 / 500) and
⇒confirmwith , continuewith
.
Please note:
The 0, 255, and 256addresses must not be employed.
Whenoperating inthe active/passive mode, an ownaddress
(underwhich theunit canbe reached in both the passiveand
activemode) must be allocated toeach unitwhich isused as
switchingexchange.
In this case, address 1 must not be employed.
1.02 Assignment toa subscribergroup
∗(the menu is not shown otherthan instage 2)
Siedle Multisystems of stage2 can be configured as either a
totalsystemwith 2 global speechpaths or a groupsystem
with both one globaland a maximumof 15 localspeech
paths.
One group address is assigned toeach subscriber to a
group, inadditionto thelogic address.
Two globalspeech paths: Group address= 0
Group system: Group address is = 1- 15
⇒Enter respective group address and
confirmwith
Continuewith
.
Tip:
∗)
The programmed value of a group assignment must
correspond to the wiringof thegroup speech paths
7xx/ 8xx.When executingthe planning, this requirement
must already be regarded.
The group address must be setupto "0"in backward
compatible systems.
Speech circuit 2
Basic parameters
programming <OK>
Log.address
1-500__1
Group?
0-150

5
Programming-
instruction
1.03 Speechcircuit 2
The HT644-.. unitis prepared for connecting two physical
speech paths.
If the second speech pathisnot wired, or ifitis employed
as a group speech path,it must be deactivatedhere.
⇒Deactivate speechpath two: Enter "0"
⇒confirmwith , Continue with
..
Please note:
The (global) speech path 2 must be deactivated in group
systems in order to avoid malfunctions.
1.04 Active / passive mode
(isonly possiblein combination with a MFM611-10 unit)
In systemswhich consist of severalswitching exchanges,
every unit can takeboth the activeand passive state, that is,
the "switching-exchange function" (address 1) can be
switched-over to each switching exchange. Only one
switchingexchange can be switched into theactive state, at
any time. In addition to the originaladdress, anadditional
(virtual)address 1 which isallocated to this switching
exchange which assumes allfunctionalities of the internal-
telephone-switching exchange. Activation is througha MFM
key (please,refer to itemNo. 7.05, „Allocating MFM“). Exactly
that unit becomes active at which the respectiveMFMkey is
actuated, however, allother switching exchanges become
automaticallypassive. The status message „A“ or „P“ shows
the respective operatingstate inthe displayscreen.
⇒Activate the active / passive mode:
Enter "1" and confirmwith , Continue with
..
Please note:
The active/passive mode must be set at all switchable
switchingexchanges.
No unit must be programmed as originaladdress 1.
Callredirections cannot be performed fromunits with enabled
active/passive mode.
Video mode
An HT644.. unit with active/passive function is also possible
in combination with an HTZ 442-0 unit, however, in the
"backward compatible" operationalmode only. When the
active/passive mode is activated, allspecialfunctions for the
"switching exchange" (lighting,Ffunctions, switching
functions, etc,) must be allocated to MFMkeys, however, the
functions for the originaladdress(passivestate) are allocated
to the special keys of the original-HTkeyboard.
Speechcircuit2
inst. Y=1/N=01
aktive/passive
mode? Y=1/N=00

6
HT644-02
1.05 Videomode
In combination with the VCO 640 video controller, a monitor
which isallocated to the HT644-.. unitcan be directly
connected by means of the integratedvideo-control
interface, or by means of a porter’s-desk camera through
output 12.
The respective video mode must be set at the HT.
Video mode 0 = no VCO-640 unitispart of the system
1= convenient one-channelvideo
2= isnot used
3= multichannelvideo (VCS system)
⇒Enter number of the system-video mode,
confirmwith
or continue with
1.06 Systemmode of operation
Twodifferent operatingmodes can be selectedforthe
Siedle Multisystem:
Backwardcompatible (old):
For older systems (with HT44x-0 orHT64x-0 units) with an
address rangeof amaximumof 254 subscribers, and with
HTZ 442-0 units, as wellas equipped with a limited range of
functions (ingeneral forsystemswith adeliverydatebefore
2001).
Stage 2 (new):
For systemswith an expanded range of functions and
addresses up to amaximumof 500 subscribers(ingeneral
for systemswith adelivery datefrom2002, and/or the ES
235 option).
⇒If “backward compatible“ isrequired: Enter "1"
If stage 2 isrequired: Enter "0"
⇒confirmwith .
Continue with
.
Please note:
As amixed mode isnotpossible, allunits of thetotal
systemmust be programmed to the very sameoperating
mode.
Language
Video mode?
0-30
Compatible?
Y=1/N=00

7
Programming-
instruction
1.07 Setting-upthe language of the respective country
The text outputin the display screen can be setup in 5
country languagesat any time.
G = 1German
UK = 2English
F= 3French
NL = 4Dutch
I = 5Italian
⇒Enter the respective digit and confirmwith
Continuewith
.
TLP call menue ⇒Exit to main menu with
Land/Country ?1
D=1GB=2F=3NL=4

8
HT644-02
2 Door-parallel-call menu
The door-parallelcallis aspecial, simultaneous door callto
subscriberswith different unit addresses. A globaldoor-
parallelcallto any number of subscribers ispossiblein
Siedle Multisystems.
In addition,a further parallelcallper groupcan be
programmed in group systems (stage 2).
⇒Openmenu with "1", confirmwith
or continue with
2.01 Receiptof adoorparallel call (ingeneral)
Enableready-to-receive state for a globaldoor parallelcall.
2.02 Receiptof adoorparallel call forgroups
Enableready-to-receipt state for a door parallelcallwithin
the own group.
⇒Enable with "1", confirmwith
or continue with
⇒Exit to main menu with .
Please note:
The corresponding door-parallelcall (calling function)is
programmed in thedoor-loudspeakercontroller.
Up to a maximumof 4 subscribers can be programmed
without any limitations to a globalor a group-parallelcall
receipt.
Whenthe power supplyis calculated for systemswith more
than 4 subscribers, the double connectedload must be
applied for each subscriber.
In combination with multichannel-video applications, the
receipt of door-parallelcalls must be enabled into the Video
controllerVCO 640-..for the corresponding monitor-
switchingoutputs.
Collective-callmenu
ReceiveTLP call
group Y=1/N=00
ReceiveTLP call
gener.. Y=1/N=00
TLPcall menu
with<OK>

9
Programming-
instruction
3 Collective-call menu
In the Siedle Multisystem, collective calls can be enabled
and received by means of the HT644-... unit.
Two types of collective callsare possible:
- A generic-collective callto allsubscribers with
authorization to receive.
- A group-collective callto subscribers withinthe selected
group only .
⇒Openmenu with "1", confirmwith
or continue with
3.01 Authorizationtosendcollective calls
Authorization to send / transmit collective calls
Tip:
Collective callsare enabledby pressing the key
and entering the respective group number.
0 = generic-collective call
1-15: Group-collective call
3.02 Authorizationtoreceive a collective call
– ingeneral
Authorization to receive generic-collectivecalls
3.03 Authorizationtoreceive group-collective calls
Authorization to receive collective calls fromthe own group
⇒Activate with "1", confirmwith .
Continue with
.
Exit to main menu with .
Please note:
Amaximumof 40 collective-call-receiving subscribers are
possible in thesystem.
Alarmand emergency
callmenu
Receivecall
group Y=1/N=00
Coll. call.
Y=1/N=00
Receivecall
gener.Y=1/N=00
Coll. call menu
with<OK>