ST Teseo-VIC3DA User manual

EVB-VIC3DA
Teseo-VIC3DA Evaluation Board
Quick Start Guide

Quick start guide - contents
2
3
Introduction to EVB-VIC3DA
Connect and start EVB-VIC3DA
Teseo-Suite configuration and startup
Documents & related resources
4
2
1

Quick start guide - contents
3
3
Introduction to EVB-VIC3DA
Connect and start EVB-VIC3DA
Teseo-Suite configuration and startup
Documents & related resources
4
2
1

Introduction to EVB-VIC3DA
4
The EVB-VIC3DA evaluation board
is a complete standalone evaluation
platform for Teseo-VIC3D/DADead-
Reckoning GNSS module
The Teseo-VIC3DA module is an
easy-to-use Dead-Reckoning Global
Navigation Satellite System (GNSS)
stand-alone module, embedding
Teseo III single die stand-alone
positioning receiver IC working on
multiple constellations (GPS,
GLONASS, Beidou, Galileo, QZSS)
Top view
Front panel
Rear panel

EVB-VIC3DA –front and rear panels
5
… Yellow LED
PWR Red LED
PPS Green LED
SMAAntenna connector
… Yellow LED
SD/MMC card
UART/USB connector
Reset Button
On/Off Switch button
Front panel
Rear panel
IO-ODO connector

Quick start guide - contents
6
Introduction to EVB-VIC3DA
Connect and start EVB-VIC3DA
Teseo-Suite configuration and startup
Documents & related resources
4
3
1
2

I/O ODO Connect is a 14 pins connector providing the signal reported in table
I/O-ODO Connector signals
1357911 13
12V_CAR_BAT
FWD INT-1 I2C_SCD VBAT 3.3V_GNSS GND
12V_CAR_BAT
WHELLTICK INT-2 I2C_SDA VBAT_VIC3 3.3V_VIC GND
2 4 6 8 10 12 14

Connect the USB cable between PC USB and the EVB-VIC3DA UART port
Connect GNSSAntenna to the SMA input connector
Press the power on button
Verify that the RED Power LED is ON
Connect and start EVB-VIC3DA
8
1
2
3
41
2
3
4

Quick start guide - contents
9
Introduction to EVB-VIC3DA
Connect and start EVB-VIC3DA
Teseo-Suite configuration and startup
Documents & related resources
4
2
1
3

Download and install the
Teseo-Suite from
www.st.com
Download and install the
Silicon Labs VCP Driver
from www.silabs.com
Install Teseo-Suite and VCP driver
10
The Teseo-Suite is a powerful PC Tool able to manage the
EVB-VIC3DA evaluation board

•During the application start-up, the Configuration Session panel is shown
• Click the ‘Add Device’ button to add a new entry
Teseo-Suite - start
11
1
2
1
2

•Set the Hardware type: STA8090
Teseo-Suite –configuration device
12
Set the GNSS Device Name: EVB-VIC3DA
Enable Add Control Port
Set the Protocol: NMEA
Set the Port Name: according to the
discovered on the PC
Configure the port as following table:
Click the Ok button
Baud rate Data bits Stop Bits Parity Handshake
115200 bps 8 Bits 1 Bit None None
1
2
3
4
5
6
7
1
2
3
4
5
6
7

In the Configuration Session panel a new entry (row) is shown
Enable Connect Ctrl port
Click the Connect button
Teseo-Suite –connect the device
13
1
2
3
12 3

In the summary panel, the GNSS EVB-VIC3DA state is reported
Click on the NMEA output window to inspect the NMEA stream
Teseo-Suite –device working
14
1
2
1
2

The NMEA Decoding panel is shown
The NMEA Stream can be seen and inspect
Teseo-Suite –inspect device
15
1
2
1
2

Click Help menu to access User-Manual
User-Manual reports all information needed
Teseo Suite –extra features
16
1
2
1
2

Now you can enjoy the EVB-VIC3DA and explore all its features with
the Teseo-Suite
Enjoy with EVB-VIC3DA
17

Quick start guide - contents
18
Introduction EVB-VIC3DA
Connect and start EVB-VIC3DA
Teseo-Suite configuration and startup
Documents & related resources
3
2
1
4

•Teseo-VIC3DA: Webpage
•Data-sheet
•Hardware User Manual
•Software User Manual
•EVB-VIC3DA: Webpage
•Datasheet
•User Manual
•Quick Start Guide
•Teseo-Suite: Webpage
•Datasheet
•Install program
Documents & related resources
10/29/2021 19
All documents are available on: www.st.com