Stamina 20-1099A User manual

Cancer and Reproductive Harm www.
P65Warnings.ca.gov
Consult your physician before starting this
or any exercise program. This is especially
important if you are over the age of 35,
have never exercised before, are pregnant,
or suffer from any health problem. This
product is for home use only. Do not use
in institutional or commercial applications.
Failure to follow all warnings and instructions
could result in serious injury or death.
The Studio Barre is NOT intended to support the full body weight of the user. Do not apply
entire body weight to the Studio Barre. Failure to follow all warnings and instructions
could result in bodily injury and/or property damage.
To reduce the risk of serious injury, read the following Safety Instructions before using the
Studio Barre.
When calling for parts or
service, please specify the
following number:
Model# 20 -1099A
SAFETY INSTRUCTIONS
MADE IN CHINA
© 2013 Stamina Products, Inc.
2019, 04
1. Save these instructions and ensure that other exercisers read this manual prior to using the
Studio Barre for the
rst time.
2. Read all warnings and cautions posted on the Studio Barre.
3. The Studio Barre should only be used after a thorough review of the Owner’s Manual. Make sure that it is properly
assembled and tightened before use.
4. We recommend that two people be available for assembly of this product.
5. Keep children away from the Studio Barre. Do not allow children to use or play on the Studio Barre. Keep children
and pets away from the Studio Barre when it is in use.
6. It is recommended that you place this exercise equipment on an equipment mat.
7. Set up and operate the Studio Barre on a solid level surface. Do not position the Studio Barre on loose rugs or
uneven surfaces.
8. Make sure that adequate space is available for access to and around the Studio Barre.
9. Before using, inspect the Studio Barre for worn or loose components, and securely tighten or replace any worn or
loose components prior to use.
10. Use the Studio Barre at a height comfortable to your practice. Using the Studio Barre at a height beyond your
comfort level and experience level could cause the product to tip or fall.
11. Always make sure that the Crossing Barre(3) is adjusted to the same height with Spring Pins(6) in parallel holes in
Uprights(2).
12. Consult a physician prior to commencing an exercise program and follow his/her recommendations in developing your
tness program. If at any time during exercise you feel faint, dizzy, or experience pain, stop and consult your physician.
13. Always choose the workout which best ts your physical strength and exibility level. Know your limits and train within
them. Always use common sense when exercising.
14. Do not wear loose or dangling clothing while using the Studio Barre.
15. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross training shoes
that t well, provide foot support, and feature non-skid rubber soles.
16. Be careful to maintain your balance while using, mounting, dismounting, or assembling the Studio Barre, loss of
balance may result in a fall and bodily injury.
17. The Studio Barre should be used by only one person at a time.
18. The Studio Barre is for consumer use only. It is not for use in public or semipublic facilities.
!CAUTION
!WARNING
!WARNING
!WARNING
This Product is Distributed Exclusively by
2040 N Alliance Ave, Springeld, MO 65803
Customer Care
1 [phone]
customer[email protected]
www.staminaproducts.com

Part # Part Name Qty
1 Base Frame 2
2 Upright 2
3 Crossing Barre 1
4 Quick Release 2
5 Endcap (38mm) 4
6 Spring Pin 2
7 Bushing 2
8 Round Plug 2
9 Set Screw (M4 x 0.7 x 4mm) 2
10 Button Pin 2
11 Caution Label 1
12 Caution Decal 1
13 Studio Barre DVD 1
14 Carry Bag 1
Products shipped to the manufacturer must be in the original shipping carton with freight prepaid. All expenses for repairing or replacing
the product, including the cost of shipping it back to the original purchaser, will be covered by the manufacturer. This warranty gives you
specic legal rights, and you may have other rights which vary from state to state.
If the product should, for any reason, become defective for a period of 90 days on the parts and one year on the frame from the
date of the purchase, the manufacturer will replace the product once it is returned to the manufacturer. This warranty does not
apply to any damage caused by accident, return transit, improper assembly, alteration, abuse, or misuse. There are no other
warranties other than those expressly set forth herein.
This product is warranted to be free from defects in material and workmanship and to be in perfect working order at the time of
purchase. This warranty applies to personal, family or household use. This warranty does not apply to use in athletic clubs, health
clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities.
Product Parts Drawing and Parts List
LIMITED WARRANTY
Assembly of The Studio Barre
Adjustment
Holes
B.
A.
STEP 1
Refer to illustration A. Loosen the QUICK RELEASE(4). Insert
the BASE FRAME(1) into the UPRIGHT(2) until the BUTTON
PIN(10) gets into the hole in the bottom end of the UPRIGHT(2).
Tighten the QUICK RELEASE(4) to lock the BASE FRAME(1) in
position securely. Repeat on other side.
STEP 2
Refer to illustration B. Pull the SPRING PIN(6) then insert an
UPRIGHT(2) through the CROSSING BARRE(3). Release the
SPRING PIN(6) so it catches in one of the adjustment holes and
locks the UPRIGHT(2) in place. Tighten the SPRING PIN(6) to
lock the UPRIGHT(2) in place securely. Repeat on other side
and position the CROSSING BARRE(3) at the same height as
other side.
To adjust the height of the CROSSING BARRE(3), turn the
SPRING PINS(6) counter clockwise until the knob portion can
be pulled. Pull both SPRING PINS(6) at the same time and slide
the CROSSING BARRE(3) up or down to adjust. Release the
SPRING PINS(6) to lock the CROSSING BARRE(3) in the desired
adjustment holes. Rotate the SPRING PINS(6) clockwise to lock
the CROSSING BARRE(3) securely.
NOTE: Always make sure that the CROSSING BARRE(3) is
adjusted at the same height.
Crossing Barre Adjustment