Standby Vega User manual

Vega – Manual
WAM8VEGAA 1 Standby AB – standbygroup.se
Vega
Thank you for choosing a product from Standby.
Safety
WARNING
This product contains high intensity LED devices. To prevent eye damage, do not look into the
light beam at close range.
Technical Data
Attribute Units
Lens Polycarbonate
Color, lens Amber, blue or clear lenses with coating
Color, LED, End modules Amber, blue or white
Color, LED, Inboard modules Amber, blue or white
Cable Amber and blue 5 m
White 6 m
Voltage 10-24 V DC
Power consumption 5 A @ 13.5 V
Max 4.3 A @ 13.5 V
Length Amber 835 mm, 1280 mm or 1590 mm
Blue 1280 mm or 1590 mm
White 1280 mm
Hei
g
ht 67 mm
Width 267 mm
Approvals Blue and amber ECE R65 I
Blue, amber and white ECE R10, EMC
!

Vega – Manual
WAM8VEGAA 2 Standby AB – standbygroup.se
Parts Overview
A. Front
B. Rear
1. Front module
2. Rear module
3. Corner module
4. T-rail
5 or 6 m cable
Control panel with fixing system
Dimensions

Vega – Manual
WAM8VEGAA 3 Standby AB – standbygroup.se
Installation
Table 1. Installation – General recommendations
1. Use fixing screws, by hand, to attach the roof brackets on the t-rails of the lightbar bottom. Do not tighten.
2. Pre install lightbar with the brackets on the vehicle roof rails.
The Standby label is placed on the lightbar FRONT part.
3. Align the lightbar with the lines of the B-pillar.
4. Cabling preparations:
1. Mark a suitable location for the lightbar cables access hole.
2. Pre drill its center.
5. Pre install the lightbar and brackets on the vehicle
roof rails. Make sure that the lightbar top line is
horizontal.
6. Adjust and tighten the fixing screws (brackets and lightbar). 7. Feed the lightbar cables through the vehicle roof or
the windshield.

Vega – Manual
WAM8VEGAA 4 Standby AB – standbygroup.se
Connections
Table 2. Vega Lightbar Blue.
Wire Functions Connect to
Black Power supply Good and suitable
ground
Red Power supply 9-32 V DC via a 5 A
fuse
Blue Warning light, ON 9-32 V DC via a 5 A
fuse
Yellow Not used

Vega – Manual
WAM8VEGAA 5 Standby AB – standbygroup.se
Table 3. Vega Lightbar Amber.
Wire Functions Connect to
Black Power supply Good and suitable
ground
Red Power supply 9-32 V DC via a 20 A
fuse
Blue Running light, IN – OUT 9-32 V DC
Purple Running light, LEFT –
RIGHT
9-32 V DC
Green Running light, RIGHT –
LEFT
9-32 V DC
Yellow Warning light, REAR 9-32 V DC
White Warning light,
CORNERS
9-32 V DC
Orange Not used
Brown Warning light,
COMPLETE BAR
9-32 V DC

Vega – Manual
WAM8VEGAA 6 Standby AB – standbygroup.se
Table 4. Vega Lightbar White.
Wire Functions Connect to
Cable 1 Rear LED, LEFT –
RIGHT
9-32 V DC via a 5 A
fuse
Cable 2 Alley / 45" LED light 9-32 V DC via a 5 A
fuse
Cable 3 Front LED, LEFT –
RIGHT
9-32 V DC via a 5 A
fuse
Cable 4 Power supply Good and suitable
ground
Cable 5 Power supply Good and suitable
ground
Cable 6 Alley / 45" LED, LEFT 9-32 V DC via a 5 A
fuse

Vega – Manual
WAM8VEGAA 7 Standby AB – standbygroup.se
Maintenance
Note
Use a mild car wash shampoo and a sponge that is gentle/appropriate to the lightbar surface
as well as the vehicle surface.
CAUTION
When using high-pressure cleaner:
Water pressure at a maximum of 80 bar.
Minimum distance of 80 cm between the gun and the lightbar.
Direct the gun so that the spray pattern hits the surface at a 90° angle.
Always thoroughly rinse with clean water after a high-pressure wash.
Follow the steps above to avoid negative impacts on packing seal, logos and decals.
Caution
Do not use degreaser.
Caution
Machine wash with brushes is acceptable, as long as the brushes are clean. However this will
increase the risk of the plastic becoming matte and scratchy.
!
!
!
!