Stelpro SILBH2060 SERIES User manual
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future reference.
If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
, according to the effective
in your region.
The following instructions must be adhered to in order to avoid personal injuries or property damages, serious injuries and potentially fatal electric shocks.
Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.
Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
This unit must be .
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative). Use this heater only as described in this
It corresponds to based on a standard ceiling height of
capacity to heat a room. If needed, refer to a specialist (industrial and commercial buildings) who will be able to calculate these heat losses and optimize the
indicated in the installation section.
S
Y
S
T
È
M
E
Q
U
A
L
I
T
É
C
E
R
T
I
F
I
É
-
R
E
G
I
S
T
E
R
E
D
Q
U
A
L
I
T
Y
S
Y
S
T
E
M
INSSILBH20600314
SILBH2060 SERIES
BATHROOM FORCED AIR HEATER
USER’S GUIDE
REPLACEMENT COMPONENT LIST INCLUDED
WARNING
For further information or to consult this guide online, please visit our website at www.stelpro.com
This unit
complies
with CSA
standards
2INSSILBH20600314
Because this unit is hot when in use, it may pose risks even in normal operation. Therefore, be and when using it. To avoid burns, do not
let bare skin touch hot surfaces. The unit must cool down for few minutes since it will stay warm for some time after shut-down. Extreme caution is necessary
when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
and away from the side and rear.
Never block air vents (with objects or other items). You risk damaging the heater and the obstruction could lead to electric shock or overheating, which could
Some areas are dustier than others. Thus, it is the user’s responsibility to evaluate if the unit based on the amount of dirt accumulated on
in accordance with these instructions.
The thermal protection activation indicates that the unit has been subjected to abnormal operating conditions. If the thermal protection remains activated or
damaged. (Refer to the )
Before unplugging the unit, all controls must be in the “OFF” position and the current from the main breaker panel should be cut. (The general switch may be
repair centre. (Refer to the limited warranty)
Make sure that all the electrical connections have been secured and made properly. Pull each wire to ensure it is not loose in the connector or the terminal
If an option must be added, make sure it has been approved by Stelpro. This way, it will ensure that it has been tested in accordance with our safety rules and
that an appropriate installation has been planned into the unit.
VOLTS 240/208 V
AMPERES 8.3 A
7.5 lb / 3.4 kg
5 1/2” / 140 mm
10 5/8” / 270 mm
16 1/2” / 420 mm
IMPORTANT NOTES :
This unit must be permanently secured to one of the bathroom walls and must only be used to heat the room where it is installed.
Never use this unit within arm’s reach while in the shower, the bathtub or near a sink.
Position the unit so the plug is easy to reach.
Never secure the unit to walls made of synthetic materials.
Only use the fan heater as a wall fitment and in the vertical position.
SPÉCIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
WARNING
instances, the instruction manual may not entirely match all the functions of the actual product. Therefore, the actual product and packaging, as well as the name
and illustration, may differ from the manual.
3INSSILBH20600314
INSTALLATION
TECHNICAL DRAWINGS AND INSTALLATION
those near the unit can withstand heat.
FRONT
SIDE
BACK
6"
152mm
15 7/16"
393mm
3 9/16"
90mm
5 1/8"
130mm
1 13/16"
46mm
JUNCTION
BOX
1 1/16"
26mm
5 3/8"
137mm
16 3/4"
425mm
10 3/8"
263mm
12"
305mm
12"
305mm
Wall
Wall
Floor
Minimum
12” (305 mm)
Minimum
12” (305 mm)
Minimum
12” (305 mm)
3 feet (91 cm)
mm)
6” (152 mm)
ILL. 01 ILL. 02 ILL. 03
4INSSILBH20600314
The fan heater has two knobs, one for the 60-minute timer and one for the thermostat.
ROOM WARM-UP WITH TEMPERATURE CONTROL
From the position marked «
turns on. The thermostat maintains the required room temperature by automatically turning on and off the fan heater. The more you turn the knob clockwise, the
QUICK ROOM WARM-UP
SAFETY IN CASE OF ABNORMAL OPERATION
In the event the unit overheats, the built-in protection system automatically deactivates the heating elements and the motor, effectively stopping the fan heater
operation. In this case, the unit is inactive, but the warning lamp is on.
OPERATION
INSTALLATION AND OPERATION
ELECTRICAL CONNECTION
ILL. 04
5INSSILBH20600314
MAINTENANCE/FILTER
MAINTENANCE
elements against dust and dirt.
right or the left side.
making sure
to reinstall it on the unit.
1 BLO-SILBH2060
2 ELF-SILBH2060
3
4
5 TIM-SILBH2060 60-MINUTE TIMER
6 MO-SILBH2060 MOTOR
7 ST-SILBH2060 THERMOSTAT
8 BOUT-SILBH2060 KNOB
FIL-SILBH2060
8156
9
27
4
3
9
REPLACEMENT COMPONENT LIST
6INSSILBH20600314
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
, Stelpro warrants its products and their components against
defects in workmanship and/or materials for the following periods from the date of purchase:. This
If at any time during the warranty period the unit becomes defective, you must cut off the power supply at the main electrical panel and contact 1)
your installer or distributor, 2) your service center or 3) Stelpro’s customer service department. In all cases, you must have a
and provide the . Stelpro reserves the right to examine or to ask one of its representatives to
examine the product itself or any part of it before honoring the warranty. Stelpro reserves the right to the entire unit, its purchase
price or a defective part. Please note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and
carried out by persons authorized by Stelpro.
Before returning a product to Stelpro, you must have a Stelpro authorization number (RMA). To obtain it, call the customer service department at:
(electricians and distributors - French), (electricians and distributors - English), or (consumers).
The authorization number must be clearly written on the parcel or it will be refused.
This warranty is exclusive and in lieu of all other representations and warranties (except of title), expressed or implied, and Stelpro expressly disclaims
Stelpro’s liability with respect to products is limited as provided above. Stelpro shall not be subject to any other obligations or liabilities whatsoever,
whether based on contract, tort or other theories of law, with respect to goods or services furnished by it, or any undertakings, acts or omissions
services, shutdowns, slowdowns, or for other types of economic loss or for claims of a dealer’s customers or any third party for such damages. Stelpro
disaster or an event out of Stelpro’s control, including, but not limited to, hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage,
negligence of the user or owner of the product. Moreover, it does not cover the cost of disconnection, transport, and installation.
The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price, . Any parts
replaced or repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty
period. This warranty will be considered null and void and Stelpro will have the right to refuse any claims if without
corrosion or discoloration caused by excessive heat, chemical cleaning products and abrasive agents. It does not cover any damage that occurred
during the shipping.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some of them do not allow limitations
may have other rights which vary from state to state or from province to province.
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY
Table of contents
Other Stelpro Heater manuals
Stelpro
Stelpro SCR series User manual
Stelpro
Stelpro UNIWATT AZUR UAC 01 Series User manual
Stelpro
Stelpro SIL2030 series User manual
Stelpro
Stelpro PDH0758W User manual
Stelpro
Stelpro ASKS series User manual
Stelpro
Stelpro Oxford Series User manual
Stelpro
Stelpro ZENITH SIRH1501W Series User manual
Stelpro
Stelpro AWFA Series User manual
Stelpro
Stelpro ALUX306052 User manual
Stelpro
Stelpro AALUX2 SERIES User manual
Stelpro
Stelpro SPIDER User manual
Stelpro
Stelpro ASB Series User manual
Stelpro
Stelpro ALUX1 Series User manual
Stelpro
Stelpro SCAS Series User manual
Stelpro
Stelpro pulsair RWF Series User manual
Stelpro
Stelpro ACW1000 Series User manual
Stelpro
Stelpro Spider SGH series User manual
Stelpro
Stelpro PRIMA SPR Series User manual
Stelpro
Stelpro PCH series User manual
Stelpro
Stelpro ASILVC2060 Series User manual
Popular Heater manuals by other brands
Twin-Star International
Twin-Star International DFH-107-T operating manual
Sealey
Sealey AB708.V2 manual
Thermofilm
Thermofilm HEATSTRIP ELEGANCE THE RA Series product manual
Toyostove
Toyostove Toyotomi Laser 730 Assembly, installation and operation instructions
Dimplex
Dimplex XL6N Installation and operating instructions
ATC
ATC iLifestyle quick start guide
