Steris 5095 User manual

56404485
Revision C
STERIS 5095 General
Surgical Table
Operator Manual

56404485_C STERIS 5095 General Surgical Table Operator Manual

iii
Operator Manual STERIS 5095 General Surgical Table 56404485_C
TABLE OF CONTENTS
Section Number Description Page
1 A word from STERIS ....................................................................................................................................... i
1.1 Introduction.......................................................................................................................................i
1.2 Advisory.............................................................................................................................................i
1.3 Indications for Use............................................................................................................................i
1.4 Waste Disposal .................................................................................................................................i
1.5 Service Information .........................................................................................................................ii
1.6 Associated Publications ..................................................................................................................ii
1.7 Contact Information ........................................................................................................................ii
2 Safety Precautions and Pinch Points .......................................................................................................... 1
2.1 Safety Precautions and Pinch Points Introduction....................................................................... 1
2.2 Introduction..................................................................................................................................... 1
2.3 Warnings and Cautions .................................................................................................................. 1
2.4 Pinch Points .................................................................................................................................... 7
3 Tabletop Articulation and Weight Limitation ........................................................................................... 11
3.1 Tabletop Articulation and Weight Limitation.............................................................................. 11
3.2 Positioning Patient on Table........................................................................................................ 11
3.3 Table Repositioning With Patient Aboard Not For Patient Transport! .................................... 12
3.4 Patient Safety Straps ................................................................................................................... 12
4 Definitions of symbols ................................................................................................................................ 13
4.1 Symbols on Table ......................................................................................................................... 13
4.2 Hand Control Symbols.................................................................................................................. 15
5 Description and Specifications................................................................................................................... 19
5.1 General Description ...................................................................................................................... 19
5.2 Overall Size (W x L x H)................................................................................................................. 20
5.3 Weight ........................................................................................................................................... 20
5.4 Range of Motion ........................................................................................................................... 21
5.5 Line Power Input........................................................................................................................... 21
5.6 Environmental Conditions............................................................................................................ 21
5.7 Transportation/Storage Conditions............................................................................................. 21
5.8 EMC/High-Frequency Interference ............................................................................................. 24
5.9 Essential Performance ................................................................................................................. 25
5.10 Image Amplification Coverage ..................................................................................................... 25
6 Before Using The Table............................................................................................................................... 27
6.1 Warnings and Cautions ................................................................................................................ 27
6.2 Uncrating, Installing and Performing Maintenance.................................................................... 28
6.3 Grounding...................................................................................................................................... 28
6.4 Positioning the Table.................................................................................................................... 28
6.5 Installing Battery Fuse (F8).......................................................................................................... 28
6.6 Installing Main Control Fuses (F6 and F7) .................................................................................. 29
6.7 Connecting Table to AC Power .................................................................................................... 30
6.8 Connecting Universal Hand Control............................................................................................. 31
6.9 Connecting Optional Foot Control ............................................................................................... 32
6.10 Installing/Removing Table Pads.................................................................................................. 32
6.11 Installing/Removing X-Ray Top................................................................................................... 33

iv
56404485_C STERIS 5095 General Surgical Table Operator Manual
6.12 Accessories/Side Rails ................................................................................................................. 34
7 Installing/Removing Dual-Articulating Head Rest.................................................................................. 37
7.1 Installing/Removing Dual-Articulating Head Rest ..................................................................... 37
7.2 Installing the Head Rest............................................................................................................... 37
7.3 Removing the Head Rest ............................................................................................................. 37
8 Installing/Removing Leg Section............................................................................................................... 39
8.1 Installing the Leg Section ............................................................................................................. 39
8.2 Removing the Leg Section ........................................................................................................... 40
9 Surgical Table Operation............................................................................................................................. 41
9.1 Warnings and Cautions ................................................................................................................ 41
9.2 Operating the Surgical Table........................................................................................................ 42
9.3 Introduction................................................................................................................................... 44
9.4 Operating the Universal Hand Control ........................................................................................ 45
9.5 Message Display With Numeric Error Codes.............................................................................. 46
9.6 Power-On Error Messages .......................................................................................................... 48
9.7 Reverse Patient Orientation ........................................................................................................ 49
9.8 Optional Foot Control Operation ................................................................................................. 49
10 Backup (Override) Control System............................................................................................................. 51
10.1 Introduction................................................................................................................................... 51
10.2 System Operation......................................................................................................................... 51
10.3 Backup Hand Control Description................................................................................................ 52
10.4 Return Backup Control System ................................................................................................... 53
11 Routine Maintenance .................................................................................................................................. 55
11.1 Read Before Performing Routine Maintenance ......................................................................... 55
11.2 Bi-Weekly Maintenance ............................................................................................................... 56
11.3 Monthly Maintenance .................................................................................................................. 56
11.4 Replacement Parts ....................................................................................................................... 56
11.5 Auto Limit Sensor (ALS) Check..................................................................................................... 57
11.6 LEVEL Check.................................................................................................................................. 58
11.7 Auxiliary Control Check................................................................................................................. 58
12 Guidelines for Cleaning Surgical Tables.................................................................................................... 59
12.1 Introduction................................................................................................................................... 59
12.2 Disinfectants ................................................................................................................................. 59
12.3 Cleaning Materials ........................................................................................................................ 59
12.4 Prolonging Mattress and Pad Lives ............................................................................................ 60
13 Instructions for Cleaning Surgical Tables ................................................................................................. 61
13.1 Introduction................................................................................................................................... 61
13.2 Removing Gross Soils (After each use and weekly) ................................................................... 62
13.3 Cleaning Tabletop and Pads (After each use and weekly)......................................................... 62
13.4 Cleaning Lower Surfaces, Yoke, Shrouds and Base (After each use and weekly).................... 62
13.5 Cleaning the Hand Control (After each use and weekly) ........................................................... 63
13.6 Cleaning Casters and Floor Locks (Weekly) ................................................................................ 63
13.7 Cleaning Areas Exposed by Articulation (Weekly) ...................................................................... 63
14 Battery Charging.......................................................................................................................................... 65
14.1 The Charging Display.................................................................................................................... 65
14.2 What You Should Know Before Charging the Batteries ............................................................ 65
14.3 Battery Charging Procedure......................................................................................................... 66
15 Sealing Table Covers ................................................................................................................................... 69
15.1 Sealing Introduction...................................................................................................................... 69

v
Operator Manual STERIS 5095 General Surgical Table 56404485_C
15.2 Two-Part Base Cover (Stainless Steel) ....................................................................................... 69
15.3 One-Part Base Cover (Plastic) ..................................................................................................... 71
16 Appendix A - EMC Compliance ................................................................................................................... 73
16.1 EMC COMPLIANCE TECHNICAL DATA......................................................................................... 73
17 Appendix B - BEACH CHAIR and advanced hand control ........................................................................ 79
17.1 Introduction................................................................................................................................... 79
17.2 Floor Locks .................................................................................................................................... 79
17.3 Hand Control for Beach Chair Operation..................................................................................... 80
17.4 Beach Chair Limits ........................................................................................................................ 80
17.5 Preparing for Beach Chair Mode.................................................................................................. 80
17.6 Entering Beach Chair Mode ......................................................................................................... 81
17.7 Exiting Beach Chair Mode ............................................................................................................ 81
17.8 Level Table Function..................................................................................................................... 82
17.9 Record Memory Modes................................................................................................................ 83

vi
56404485_C STERIS 5095 General Surgical Table Operator Manual

vii
Operator Manual STERIS 5095 General Surgical Table 56404485_C
LIST OF FIGURES
Description Page
Figure 2-1 Pinch Points (Illustration 1 of 2) ...................................................................................................... 8
Figure 2-2 Pinch Points (Illustration 2 of 2) ...................................................................................................... 9
Figure 4-1 Universal Hand Control................................................................................................................... 16
Figure 5-1 Table Components (Typical) ........................................................................................................... 20
Figure 5-2 Range of Motion ............................................................................................................................. 22
Figure 5-3 Tabletop Dimensions, Typical ........................................................................................................ 23
Figure 5-4 Image Amplification Coverage ....................................................................................................... 23
Figure 5-5 Base Dimensions ............................................................................................................................ 24
Figure 6-1 Installing or Replacing Fuses ......................................................................................................... 29
Figure 6-2 Installing or Replacing Main Fuses F6 and F7 .............................................................................. 30
Figure 6-3 Connecting Table to Facility Power (Typical) ................................................................................ 30
Figure 6-4 Connecting Universal Hand Control............................................................................................... 31
Figure 6-5 Connecting Optional Foot Control ................................................................................................. 32
Figure 6-6 Tabletop Pads ................................................................................................................................. 33
Figure 6-7 Aligning X-ray Top Posts to Mounting Holes ............................................................................... 33
Figure 6-8 Snapping X-ray Top Into Position.................................................................................................. 34
Figure 7-1 Installing the Head Rest ................................................................................................................ 37
Figure 8-1 Universal Hand Control,LCD Screen............................................................................................... 39
Figure 8-2 Attaching Leg Section..................................................................................................................... 39
Figure 8-3 Leg Section Removal ...................................................................................................................... 40
Figure 9-1 Adjusting Dual-Articulating Head Rest ......................................................................................... 43
Figure 9-2 Universal Hand Control Screen ...................................................................................................... 44
Figure 9-3 Prompt to Select Correct Compatibility Mode .............................................................................. 45
Figure 9-4 Example of Error Code Display - Error Code 20 Shown............................................................... 46
Figure 10-1 Backup (Override) Control System ............................................................................................. 52
Figure 10-2 Backup (Override) Hand Control .................................................................................................. 53
Figure 14-1 INTELLIPOWER Panel LED Display.............................................................................................. 65
Figure 14-2 LED Relation to Battery Voltage.................................................................................................. 66
Figure 15-1 Apply Tape to Mounting Bracket ................................................................................................ 69
Figure 15-2 Ensure Base Cover Sits Flush on Base at Insert Opening ........................................................ 69
Figure 15-3 Seal Mating Areas Between Front and Rear Base Covers ........................................................ 70
Figure 15-4 Apply RTV to V-Shaped Cut-Outs ............................................................................................... 70
Figure 15-5 Seal Area Around Power Inlet...................................................................................................... 70
Figure 15-6 Seal Around Upper Plastic Covers and Column .......................................................................... 71
Figure 15-7 Seal Along Both Seams of Upper Plastic Column Covers.......................................................... 71
Figure 15-8 Install Base Cover Insert and Attach to Base Cover ................................................................. 72
Figure 15-9 Seal Seam Between Base Cover Insert and Base Cover............................................................ 72
Figure 17-1 Advance Hand Control (Required for Beach Chair Mode) .......................................................... 79
Figure 17-2 Entering Beach Chair Mode ......................................................................................................... 81
Figure 17-3 Exiting Beach Chair Mode ............................................................................................................ 82
Figure 17-4 Level Table Functions (Typical)....................................................................................................83
Figure 17-5 Record Memory Modes................................................................................................................ 84

viii
56404485_C STERIS 5095 General Surgical Table Operator Manual

ix
Operator Manual STERIS 5095 General Surgical Table 56404485_C
LIST OF TABLES
Description Page
Table 4-1 Definition of Symbols on Surgical Table ......................................................................................... 13
Table 4-2 Universal Hand Control, Symbols.................................................................................................... 16
Table 6-1 STERIS 5095 General Surgical Table Specific Accessories* .......................................................... 34
Table 9-1 Universal Hand Control and Surgical Table Compatibility Mismatch .......................................... 46
Table 9-2 Display Screen Numeric Error Codes .............................................................................................. 46
Table 11-1 Replacement Parts ........................................................................................................................ 57
Table 11-2 Replacement Parts, Pads .............................................................................................................. 57
Table 13-1 Table Cleaning and Disinfection Tasks and Frequencies............................................................ 61
Table 16-1 Guidance and Manufacturer s Declaration Electromagnetic Emissions For All Equipment
and Systems (per IEC 60601-2 Clause 6.8.3.201 a 3 Table 201) ................................................... 73
Table 16-2 Guidance and Manufacturer s Declaration Electromagnetic Immunity For All
Equipmentand Systems (per IEC 60601-2 Clause 6.8.3.201 a 6 Table 202).................................. 74
Table 16-3 Guidance and Manufacturer s Declaration Electromagnetic Immunity For Equipment and
Systems That Are Not Life-Supporting (per IEC 60601-2 Clause 6.8.3.201 b Table 204) ............. 75
Table 16-4 Recommended Separation Distances Between Portable and Mobile RF Communications
Equipment and STERIS 4095 or 5095 General Surgical Tables (per IEC 60601-2 Clause 6.8.3.201
b Table 206) .......................................................................................................................................... 76

x
56404485_C STERIS 5095 General Surgical Table Operator Manual

i
Operator Manual STERIS 5095 General Surgical Table 56404485_C
A word from STERIS
1.1 Introduction
IMPORTANT: Read this entire manual before attempting to install or operate your Surgical Table. Ensure all appropriate personnel
understand the contents of this manual.
1.2 Advisory
Safety Precautions and Pinch Points to be observed when operating and servicing the equipment are included in this manual. Do
not operate or service the equipment until you have become familiar with this information.
WARNING-PERSONAL INJURY HAZARD AND POSSIBLE REGULATORY VIOLATION:
Any alteration of the surgical table not authorized or performed by STERIS which could affect its operation will
void the warranty, could adversely affect operator safety and could violate national, state or local regulations.
Serious incidents that have occurred in relation to this medical device should be reported to the manufacturer and competent
authority in the country where the incident occurred.
1.3 Indications for Use
The surgical table is an electro-hydraulically operated and designed to support virtually all general surgical procedures including
cardiac and vascular, endoscopic, gynecology, urology, nephrectomy, neurology, ophthalmologic and orthopedics with the
addition of STERIS table accessories.
1.4 Waste Disposal
WARNING-DISPOSAL HAZARD:
This product contains materials which may require disposal through appropriately licensed and permitted
hazardous waste management firms.
CAUTION-POSSIBLE EQUIPMENT DAMAGE:
Use of incorrect hydraulic oil may severely damage the table and/or cause malfunction. Contact STERIS for
proper hydraulic oil.
The following materials may be contained within the table. When disposing of the table or its parts, ensure the proper disposal
of hazardous and other regulated waste in compliance with federal, state and local regulations.
Lead Acid (Pb/H 2SO4): gelled cell batteries located in the table base at the head end of the table. Approximate weight 5 lbs. (2
kg).
Lead (Pb) in Solder: contained in solder on circuit boards and in some miscellaneous wire connections. Minute amounts.
Electronic and Electrical Parts: not known to require special disposal at date of this manual.
Metal Parts: made from aluminum (Al), steel (Fe), cast iron (Fe), copper (Cu), and copper alloys (Cu/x), plastic, synthetic rubber,
plating (Cr, Ni, Zn, Au), and adhesives not known to require special disposal methods at date of this manual.

ii
56404485_C STERIS 5095 General Surgical Table Operator Manual
Hydraulic Oil: contained in hydraulic components located in the base, column, leg section, back section, and hydraulic system
lines and hoses.
Polyvinylchloride (PVC): Approximate weight 3.8 lbs. (1.7 kg).
1.5 Service Information
A thorough preventive maintenance program is essential for safe and proper unit operation. This manual contains maintenance
schedules and procedures which should be followed for satisfactory equipment performance. Comprehensive instructions for
monthly, quarterly and semi-annual preventive maintenance can be found in the Maintenance Manual (available from STERIS).
Only STERIS-trained personnel should attempt to perform maintenance on the table, to avoid personal injury, improper
equipment performance, invalidation of the equipment warranty or other costly damage.
Customers are encouraged to contact STERIS concerning our comprehensive preventive maintenance program. Under the terms
of this program, preventive maintenance, adjustments and replacement of worn parts are provided on a scheduled basis to help
ensure optimal equipment performance and help avoid untimely or costly interruptions. STERIS maintains a global staff of well
equipped, factory-trained technicians to provide these services, as well as expert repair services. Please contact STERIS for
details.
NOTE: A patient grounding post/potential equalization terminal (male connector, DIN 42801) is provided. The female connector
for patient grounding is not furnished by STERIS.
1.6 Associated Publications
Tech Data Sheet - 056404-492
Maintenance Manual - P764333-472
Parts Catalog (IPB) - P764333-474
PowerLift Beach Chair (IFU) - P056404-439
Field Instructions, Voltage Setting (for export) - P150832-806
1.7 Contact Information
STERIS Ireland Limited
IDA Business and Technology Park
Tullamore
County Offaly
R35 X865 Ireland
Manufactured by:
STERIS Corporation
2720 Gunter Park East
Montgomery, AL 36109 USA
TEL: [phone]
8004449009
www.steris.com
Class 1 Equipment

iii
Operator Manual STERIS 5095 General Surgical Table 56404485_C
Type B Equipment
Splash-Proof Equipment (enclosed equipment protected
against splashing water, IPX4)
Equipment not suitable for use in the presence of a
flammable anesthetic mixture with air or oxygen or nitrous
oxide.
Suitable for intermittent operation 3 min/hr.

iv
56404485_C STERIS 5095 General Surgical Table Operator Manual

Section 2 — Safety Precautions and Pinch Points
1
Operator Manual STERIS 5095 General Surgical Table 56404485_C
Safety Precautions and Pinch Points
2.1 Safety Precautions and Pinch Points Introduction
IMPORTANT: Understand the following points regarding floor locks.
Floor locks:
• Cannot be disengaged unless slide is less than 2.5 (64mm) toward short end of table base.
• When engaged, all motions are full range.
• When disengaged, all motions are full range except slide, which is limited to 2.5 (64mm)
• of travel toward short end of table base.
2.2 Introduction
The following Safety Precautions must be observed when operating or servicing this surgical table. WARNING indicates
the potential for personal injury and CAUTION indicates the potential for damage to equipment. For emphasis, certain
Safety Precautions are repeated throughout the manual. It is important to review ALL Safety Precautions before
operating or servicing the unit.
2.3 Warnings and Cautions
WARNING-PERSONAL INJURY HAZARD AND POSSIBLE REGULATORY VIOLATION:
Any alteration of the surgical table not authorized or performed by STERIS which could affect its
operation will void the warranty, could adversely affect operator safety and could violate national, state
or local regulations.
WARNING-PINCHING HAZARD:
Pinch points are created during tabletop articulation. Become familiar with all pinch points prior to
operating the table.
To avoid serious injury, keep limbs, fingers and other body areas clear of all pinch points when positioning
the table.
When manually positioning table sections, stay clear of potential pinching hazards.

Section 2 — Safety Precautions and Pinch Points
2
56404485_C STERIS 5095 General Surgical Table Operator Manual
WARNING-TIPPING HAZARD:
Do not place patient on the table unless floor locks are engaged.
The table is not to be used to transport patients. With exception of slight repositioning, as detailed in the
operating instructions, never disengage floor locks when patient is on table. Failure to heed this warning
can result in injury to both the patient and the operating room staff.
Do not use this table for patients exceeding the maximum patient weight of:
●1200lbs. (544 kg) Load, Normal and Reverse Patient Position; raise or lower only (no tabletop
articulation or slide).
●900lbs. (408 kg) Load, Normal and Reverse Patient Position; raise or lower; includes all tabletop
articulation except tabletop slide.
●600lbs. (272 kg) Load, Normal Patient Position; raise or lower; includes all tabletop articulation and full
tabletop slide.
Center tabletop over column before applying chest compressions.
Center tabletop over column before transferring patient on or off of table.
WARNING-EXPLOSION HAZARD:
Table must not be used in the presence of flammable anesthetics.
WARNING-TRIPPING HAZARD:
Route the power cord to the receptacle to minimize being tripped over by personnel in the area.
WARNING-PERSONAL INJURY HAZARD:
Failure to keep the patient properly secured with the patient safety straps at all times could result in
death or serious injury.
The table is not to be used to transport patients. With exception of slight repositioning, as detailed in the
operating instructions, never disengage floor locks when patient is on table. Failure to heed this warning
can result in injury to both the patient and the operating room staff.
Keep hands and feet clear of the unloading platform and the table base when unloading the table. Serious
personal injury could result.

Section 2 — Safety Precautions and Pinch Points
3
Operator Manual STERIS 5095 General Surgical Table 56404485_C
Healthcare professionals must ensure patients are positioned and monitored so as to prevent
compromising respiration, nerve pathways or circulation.
When installing any table accessory, check for correct attachment and tighten securely (if appropriate). Do
not use a worn or damaged accessory. Before using any accessory, ensure it has been installed properly.
Patient must be secured to the table in accordance with recommended positioning practices.
Unanticipated patient or table movement could result in death or serious injury.
When cleaning/disinfecting table, do not use phenolics which may cause patient skin burns if
inadequately rinsed off, or alcohol, which does not have sufficient cleaning/disinfecting properties.
Do not exceed 350 lbs. (159 kg) on the leg section.
Dual-articulating headrest side rails support 100 ft-lbs. (135 Nm) maximum. The headrest end rail
supports 50 ft-lbs. (67 Nm) maximum. Exceeding these limits could result in injury or equipment damage.
If the integrity of the external protective ground installation or arrangement is in doubt, operate the table
from its internal power source.
If an antistatic path is necessary, STERIS recommends antistatic pads (specifically developed for this
table) in direct contact with the patient. Table must also be positioned on antistatic floor or connected to
equalization device (equipotential connector).
Do not remove table leg section if patient is not properly positioned. Patient's torso and buttocks must be
firmly held in place by table back and seat sections and legs supported by leg supports.
WARNING-INSTABILITY HAZARD:
Possible patient or user injury, as well as table or accessory failure, may result from using STERIS table
accessories for other than their stated purpose or from using accessories manufactured and sold by
other companies on STERIS surgical tables.
WARNING-PINCHING AND TIPPING HAZARD:
Patient injury may result if the operator of this table is not completely familiar with the controls for
tabletop articulation and table operation.

Section 2 — Safety Precautions and Pinch Points
4
56404485_C STERIS 5095 General Surgical Table Operator Manual
WARNING-PERSONAL INJURY AND/OR EQUIPMENT DAMAGE HAZARD:
Repairs and adjustments to this equipment must be made only by STERIS or STERIS-trained service
personnel. Maintenance performed by unqualified personnel or installation of unauthorized parts could
cause personal injury, result in improper equipment performance, invalidate the warranty, or result in
costly damage. Contact STERIS regarding service options.
Regularly scheduled preventive maintenance is required for safe and reliable operation of this equipment.
Contact STERIS to schedule preventive maintenance.
Do not service or perform maintenance on equipment while in use.
Table is factory set to operate at a certain voltage. Use of any other power supply could result in serious
personal injury or table damage.
To avoid the risk of electric shock, this equipment must only be connected to a supply mains with
protective earth.
Use of this table in the presence of flammable anesthetics could result in serious personal injury or table
damage.
Do not use this table for patients exceeding the maximum patient weight of:
●1200lbs. (544 kg) Load, Normal and Reverse Patient Position; raise or lower only (no tabletop
articulation or slide).
●900lbs. (408 kg) Load, Normal and Reverse Patient Position; raise or lower; includes all tabletop
articulation except tabletop slide.
●600lbs. (272 kg) Load, Normal Patient Position; raise or lower; includes all tabletop articulation and full
tabletop slide.
Failure to perform periodic inspections of table could result in serious personal injury or equipment
damage.
The Auto Limit Sensors (ALS) System suggested alternative tabletop movement does not take into
account the type of surgery that may be in process or the environment (e.g., other equipment close by)
and might not be compatible with the surgical procedure. To avoid an action that could result in death or
serious injury to the patient and the operating room staff, and/or serious equipment damage, completely
evaluate the feasibility of the suggestion.
ALS System is not active during Backup Control. Ensure proper tabletop movements to prevent
patient/staff injury and/or equipment damage.

Section 2 — Safety Precautions and Pinch Points
5
Operator Manual STERIS 5095 General Surgical Table 56404485_C
During Backup Control, tabletop functions are available even if table floor locks are NOT engaged. LOCK
table before moving tabletop or transferring patient.
Use of accessories, transducers or cables with this table, other than those specified, may result in
increased emissions or decreased immunity of the table.
Do not store items on table base. Doing so may result in equipment damage or inadvertent tabletop
movement placing the patient and/or user at risk of injury.
Failure to keep all personnel and equipment clear of the table before actuating any inertia-driven or
power-driven movement could result in table damage and/or personal injury.
Hand Control must be attached to table at all times to enable safety stop and all modes of operation.
With patient in normal or reverse orientation, table in Trendelenburg and slide at head limit, center
tabletop before attempting to raise table to level or move into Reverse Trendelenburg.
Read and understand all instructions presented in this section before using the Universal Hand Control.
Follow each step in the order presented in these instructions. If you need technical assistance or
additional instructions, please contact STERIS.
Dual-articulating headrest side rails support 100 ft-lbs. (135 Nm) maximum. The headrest end rail
supports 50 ft-lbs. (67 Nm) maximum. Exceeding these limits could result in injury or equipment damage.
WARNING-DISPOSAL HAZARD:
This product contains materials which may require disposal through appropriately licensed and permitted
hazardous waste management firms.
WARNING-INFECTION HAZARD:
To protect against aerosols being reflected from potentially contaminated surfaces, wear rubber or plastic
gloves, masks and eye protection, and follow OSHA blood-borne pathogens standards when cleaning.
When cleaning/disinfecting table, do not use alcohol as it does not have sufficient cleaning/disinfection
properties.

Section 2 — Safety Precautions and Pinch Points
6
56404485_C STERIS 5095 General Surgical Table Operator Manual
CAUTION-POSSIBLE EQUIPMENT DAMAGE:
When moving the table to or from point of use, roll it carefully at moderate speed and only over smooth
floors. Maximum floor clearance is 1/4" (6.4 mm). Avoid door and elevator jambs, and obstructions
greater than 1/4" (6.4mm). If necessary, lift table over obstructions, onto trucks, etc. Lift table evenly and
only by the table base. DO NOT transport articles (including accessories) on top of the table, and DO NOT
use a forklift to move the uncrated table.
Hang the hand control from side rail of the table when not in use to avoid possible damage to the control.
When cleaning/disinfecting table, thoroughly read the cleaning fluid directions for use and follow all
directions and cautions as shown.
Do not spray cleaning fluid into electric receptacles and avoid spraying directly on emergency backup
buttons or into clearance space. Spray or drippage may settle onto electric circuits inside table causing
corrosion and loss of function.
Cleaning procedures requiring articulation of the table should be performed only by persons familiar with
table operation.
Route the hand control cord clear of any pinch points where cord could be damaged.
Use of incorrect hydraulic oil may severely damage the table and/or cause malfunction. Contact STERIS
for proper hydraulic oil.
After performing cleaning procedures, ensure pads, tabletop and X-ray tops are completely dry before
reinstalling. Moisture trapped between pads and X-ray tops may contribute to equipment damage, such
as X-ray top warpage.
Appropriate components of this surgical table have been tested and found in compliance with IEC 60601-
1-2: Edition 4 2014-02, Medical Electrical Equipment Part 1; General Requirements for Safety;
Electromagnetic Compatibility (EMC). There is, however, a potential for electromagnetic or other
interference between this equipment and other devices. Should user experience interference, relocate this
device or minimize the use of the affected equipment while this device is in operation.
Surgical table operation may be temporarily affected if portable or mobile RF communications equipment
is used in close proximity.
Medical Electrical Equipment needs special precautions regarding EMC. Put table into service according to
the EMC information provided in this manual.
Possible EMC increased EMISSIONS or decreased IMMUNITY. Do not use accessories or replacement
parts not listed in the Operator or Maintenance Manuals.