Stoane Lighting Penguin Type X User manual

Stoane Lighting Ltd
20 Dryden Road Bilston Glen Ind Est.
Loanhead Midlothian EH20 9LZ UK
T: [phone]
F: [phone]
[email protected]
www.stoanelighting.com
VAT No GB682885284
Limited Company 188910
Penguin Type X
Installation and Maintenance
Instructions
IMPORTANT: All wiring connections must be made before switching on mains power.
European Conformity
Please retain these instructions for future reference
This product should not be disposed of in your general waste
Class I - Fitting must be Earthed
Indoor Use Only
IP20
Xicato LED Module
All of our in-house printed paper
is 100% recycled and recyclable
Penguin Type X.pdf 1 08/03/2021 17:05:42

Electrical Supply
Installation must be carried out by a qualified electrician in
accordance with BS 7671:2008 Wiring Regulations.
230/240V AC 50/60Hz mains supply. A UK 13A plug is
supplied with a 3 amp fuse fitted.
Site conditions: LED equipment is more susceptible to
static damage and over voltage than previous technology.
Before handling or connecting to the mains supply ensure
that all Stoane Lighting (SL) products are protected from
static discharge and that the mains supply is to regulation.
(230V +10 -6%)
This fitting is supplied with a Xicato LED module. Refer to
the fitting label for the module version and wattage. More
information on the module can be found at
www.xicato.com/support
Mains cables must be double insulated, strain relieved
and separated from E.L.V output cables.
All connections must be made before switching on mains.
If the supply is energised prior to making the connections
to the fitting then the resulting surge will damage the LED.
This fitting must be focused with at least 0.5m distance
from any lit object. Lock in position to prevent accidental
movement.
Maintenance:
All lighting equipment is delicate and easily damaged
through misuse or inappropriate installation (mechanical
or electrical). Repairs and replacements may cause
delays and will be chargeable. Contact SL for support if
required.
All Stoane Lighting products are covered by a five year
Warranty and a 25 year Duty of Care. Products are
designed to be upgraded, adapted and refreshed using
our comprehensive ReNew service. For more information
on our ReNew service and for full Warranty terms and
conditions visit stoanelighting.com or contact us at the
address shown.
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualified person.
If the external flexible cord of this luminaire is damaged, it
shall be exclusively replaced by the manufacturer or his
service agent or similar qualified person in order to avoid
a hazard.
Installation
This fittings should be positioned on a suitable flat and
secure surface.
Adjustment
Allow fitting to cool before adjusting.
To adjust the tilt on the fitting, loosen the tilt screw
found on the side of the fitting.
Once the correct adjustment has been achieved
re-tighten the screw.
Dimming
This fitting is supplied with on board dimming via
dimmer knob on the side of the fitting.
When supplying digital equipment with the potential to
be connected to networks, physically or wirelessly (i.e.
Bluetooth, WiFi, DMX radio etc.), SL does not take
responsibility for the digital security of the equipment
or associated networks. It is the customer’s
responsibility to select a protocol suitably robust for
their requirements and to ensure responsible
utilisation of passwords.
WARNING: Do not look at exposed LED lamps in
operation. Eye injury can result.
Cleaning:
Fully isolate the fitting and allow to cool.
Clean the fitting with a slightly damp lint free cloth
from a mild solution of soap and water. The fitting
must be completely dry before reconnecting power.
Incompatible or abrasive chemicals can damage the
fitting, contact SL for advice if required.
Penguin Type X.pdf 2 08/03/2021 17:05:42

Tilt Adjustment
Dimmer
approx.
35° tilt
Penguin Type X.pdf 3 08/03/2021 17:05:42

12
3
Accessories
Circlip
MODULE AND ACCESSORIES
The fitting uses a Xicato LED module. The colour
temperature and lumen output can be found on the
product label on the fitting.
To Add/Remove accessories:
Isolate the fitting from the supply and allow to cool.
Step 1 To replace accessories remove circlip and load
accessories. Re attach circlip to secure.
Step 2 To replace reflector unscrew bezel in an anti
clockwise direction.
Step 3 Remove old reflector and fit new reflector. Refit
the bezel by screwing on in a clockwise direction.
Reflector
Bezel
Penguin Type X.pdf 4 08/03/2021 17:05:42

Stoane Lighting firmly believe that we have a responsibility as environmental
custodians, we believe that lighting equipment should be built to last, to be
repaired and to be reused. As a BCorp we have pledged to operate a business not
aiming to just be best in the world but a business best for the world. Stoane
Lighting believe that the circular economy is a fundamental aspect of how we
approach the challenges we face. If you read this at the end of the product life we
encourage you to consider how you can ensure this product sees an extended life.
If removal is unavoidable, please see the disassembly note below.
All Stoane Lighting products are supplied with a 5 year warranty and a 25 year
duty of care.
Stoane Lighting operate a ReNew division, which can take your existing fittings
and refurbish or upgrade without the need for replacing what you already have.
Through the ReNew service, Stoane Lighting provides general repair, deep cleans
and electrical safety checks on luminaires, as well as possible repainting if needed.
We will replace components that are nearing end of life, such as drivers, LEDs,
and optics. If the fittings are to be used in a new area, or the existing space is
undergoing a change in use, ReNew can offer a different mounting method or light
technical performance (such as colour tuning), if needed, alongside the addition of
on-board wireless control. ReNew as a service, depending on location, can be
done on site or by returning equipment to Stoane Lighting.
Once fittings have been repaired or upgraded through ReNew, they will start a new
five-year warrantly period, and any unwanted parts will be recycled.
Product Disassembly and Component Recylcing - While every effort has been
made to ensure that our products are built to last and are ReNewable, there may
come a point when, as a very last resort, the fittings need to be recycled. Stoane
Lighting can provide information on how the fitting can easily be disassembled into
its component parts for more effective recyling. Information on recyling services in
your local region can also be supplied on request.
For more information on the above please visit stoanelighting.com
or contact us at the address shown.
Penguin Type X.pdf 5 08/03/2021 17:05:42