Stratasys F120 Operating instructions

Part No. 405680-0001_REV_B
F120 Shared Office
3D Printing System
Site Preparation Guide


Site Preparation Guide
Page ii
Copyright
Copyright © 2019-2020 Stratasys Ltd. All rights reserved.
No part of this document may be photocopied, reproduced, or translated into any human or computer
language in any form, nor stored in a database or retrieval system, without prior permission in writing from
Stratasys. This document may be printed for internal use only. All copies, shall contain a full copy of this
copyright notice.
Liability
Stratasys shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material. Stratasys makes no warranty of any kind
with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. It is the responsibility of the system owner/material buyer to determine that Stratasys
material is safe, lawful, and technically suitable for the intended application as well as identify the proper
disposal (or recycling) method consistent with local environmental regulations. Except as provided in
Stratasys' standard conditions of sale, Stratasys shall not be responsible for any loss resulting from any use of
its products described herein.
Trademarks
Stratasys, GrabCAD, Insight and FDM are trademarks of Stratasys and/or subsidiaries or affiliates and may
be registered in certain jurisdictions. All other product names and trademarks are the property of their
respective owners.
Disclaimer
Customer acknowledges the contents of this document and that Stratasys parts, materials, and supplies are
subject to its standard terms and conditions, available on http://www.stratasys.com/legal/terms-and-
conditions-of-sale, which are incorporated herein by reference.
The specifications and/or information on which this document is based are subject to change without notice.

Page iii
Stratasys Confidential
Contents
Revision Log ................................................................................................. iv
Safety............................................................................................................ iv
Safe Environment................................................................................................................ iv
About the F120 Printer................................................................................... 1
Components ........................................................................................................................ 1
Highlights............................................................................................................................. 1
How to Use This Guide........................................................................................................ 1
Site Prep Tasks .............................................................................................. 2
Selecting the Site ................................................................................................................ 2
Physical Specifications and Space Requirements .............................................................. 2
Environmental Requirements .............................................................................................. 5
Electrical Requirements ...................................................................................................... 6
Workstation Requirements .................................................................................................. 6
LAN Requirements .............................................................................................................. 6
Receiving the Printer ..................................................................................... 7
Inspect Crate for Damage ................................................................................................... 7
Preparing For Installation............................................................................... 7
Required Tools and Equipment ........................................................................................... 7
Unpacking and Positioning the Printer ................................................................................ 8
Site Preparation Checklist ........................................................................... 12
Electrical Installation Requirements .................................................................................. 12
Environmental Requirements ............................................................................................ 12
Required Installation Tasks................................................................................................ 12


Site Preparation Guide Revision Log
Page iv
Revision Log
Revision Date Description of Changes
AJune 2019 First release of this document.
BMarch 2020 Added 240VAC note.
Safety
The following basic safety tips are given to ensure safe installation, operation, and
maintenance of Stratasys equipment and are not to be considered as comprehensive on
matters of safety. Although the F120 printers are designed to be safe and reliable, access to
areas of the printer are potentially dangerous and should be approached with caution.
Safe Environment
• Connect equipment to a grounded facility power source. Do not defeat or bypass the
ground lead.
• Know the location of equipment branch circuit interrupters or circuit breakers and how to
turn them on and off in case of emergency.
• Know the location of fire extinguishers and how to use them. Use only ABC type
extinguishers on electrical fires.
• Know local procedures for first aid and emergency assistance at the customer facility.
• Use adequate lighting at the equipment.
• Maintain the recommended range of temperature and humidity in equipment area.
• Do not use this product in an environment containing volatile or flammable compounds.


Site Preparation Guide About the F120 Printer
Page 1
About the F120 Printer
The Stratasys F120 3D printer incorporates the latest in innovative technology to provide you
with precise 3D-printed parts from a CAD design. Stratasys’ Fused Deposition Modeling (FDM)
technology provides accurate parts, including internal features, which can be used to field-test
form, fit, and function. Direct Digital Manufacturing (DDM) allows for the creation of customized
end-use parts straight from 3D CAD data. The F120 printer features a servo/belt driven XY
gantry with multiple modeling material capability.
Components
• The F120 Printer
• Welcome Kit (containing documentation on how to download your user guide and common
tools for maintaining the printer)
• GrabCAD Print Software Package
• A Computer Workstation (not sold by Stratasys, for preparing build files)
Highlights
• Maximum build area of 10 x 10 x 10 inch (254 x 254 x 254 mm)
• Touchscreen Graphical User Interface
• Wi-Fi capabilities
• Two front USB ports
• Camera for remote monitoring
How to Use This Guide
This guide provides information for selecting an appropriate location for the F120 printer. This
guide also provides instructions for unpacking and preliminary set-up. Information of particular
importance is presented in one of three formats:
A Warning: indicates a procedure that may cause injury to an operator if the
procedure is not followed. 
A Warning: will precede the paragraph of instruction to which it relates.
A Caution: indicates a procedure that may cause damage to equipment if the
procedure is not followed. 
A Caution: will precede the paragraph of instruction to which it relates.
A NOTE is used to highlight a specific point or to provide an operational tip. While
useful, a NOTE does not indicate a procedure that can cause injury or damage if it is
not followed. 
A NOTE will follow the paragraph of instruction to which it relates.


Site Preparation Guide Site Prep Tasks
Page 2
Site Prep Tasks
Selecting the Site
Decide where to install the printer based on the following:
1. Space Requirements
2. Environmental Requirements
3. Electrical Requirements
4. LAN Requirements
The F120 printers are capable of generating vibrations depending mainly on part
build geometry and material characteristics. This consideration will need to be
taken into account if locating the printer near vibration sensitive equipment.
Physical Specifications and Space Requirements
Dimensions and Weights
Make sure that the installation site floor space can accommodate the printer’s weight and
dimensions, plus required clearances. The installation location must be a flat level surface that
is stable and capable of holding 500 pounds (227 kg).
Caution:
Due to the physical size and weight of the F120 printer, it is recommended to use
a forklift when positioning the printer.
If a table is used to support the printer, the recommended height is 30 inches ± 3
inches (76 cm ± 7.6cm) and it should be capable of holding 500 pounds (227 kg).
If the table has casters, they must be lockable.
Description Weight Dimensions
Printer Crated 350 pounds (159 kg)
Width: 48 inches (122 cm)
Depth: 40 inches (102 cm)
Height: 42.75 inches (109 cm)
Printer Uncrated 295 pounds (134 kg)
Width: 34 inches (86 cm)
Depth: 28 inches (71 cm)
Height: 36 inches (92 cm)


Site Preparation Guide Site Prep Tasks
Page 3
Figure 1: F120 Center of Mass
The center of mass dimensions shown are taken from the bottom center of the
front left foot.


Site Preparation Guide Site Prep Tasks
Page 4
Minimum Operational Clearances
Sufficient rear and side clearances allow for proper air circulation, while sufficient front
clearance allows enough room for the oven door and drawers to be opened.
Right Side Clearance
(Includes additional space for
material coil boxes)
Minimum 20 inches (50.8 cm)
Left Side Clearance Minimum 4 inches (10.16 cm)
Rear Clearance Minimum 6 inches (15.24 cm)
Front Clearance Minimum 20 inches (50.8 cm)
Overhead Clearance Minimum 20 inches (50.8 cm)
Figure 2: Minimum Clearances
20 inches (50.8 cm) minimum for overhead clearance
20 inches
(50.8 cm)
Front
Rear
6 inches
(15.24 cm)
20 inches
(50.8 cm)
4 inches
(10.16 cm)


Site Preparation Guide Site Prep Tasks
Page 5
Environmental Requirements
• The F120 printer can be used in any controlled environment.
• Air quality conditions with excessive solid particulates (conductive or non-conductive) may
result in system damage.
• Air quality conditions in which airborne oils are allowed to accumulate on or within the
printer can damage the plastic components.
• System operating temperature shall be in the range of 59°F to 86°F (15°C to 30°C), with
relative humidity range of 30% to 70% non-condensing.
• System storage temperature shall be in the range of 32°F to 95°F (0°C to 35°C), with
relative humidity range of 20% to 90% non-condensing.
• Altitude shall not exceed 6561.68 feet (2000 m).
• Material storage shall be in the range of 55°F to 86°F (13°C to 30°C), with relative humidity
less than 70%.
•Noise emission (acoustic):
• <32dBA when idle
• <46dBA when building
Heat Output
Heat dissipation occurs mostly through the top of the printer. Heat output is material dependent
due to the various temperatures maintained in the build chamber.
Material Type Heat Output (while building) Heat Output (while idle)
ABS ~2300 BTU/hr ~1800 BTU/hr
ASA ~2300 BTU/hr ~1800 BTU/hr
Power Consumption
Power consumption is material dependent due to the various temperatures maintained in the
build chamber.
Material Type
Power
Consumption
(while building)
Power Consumption
(while idle)
Power
Consumption
(while sleeping)
ABS 650 W 510 W 10 W
ASA 650 W 510 W 10 W


Site Preparation Guide Site Prep Tasks
Page 6
Electrical Requirements
AC Power Requirements
• 50/60 Hz.
• Voltage: 100-132, 200-240 VAC.
Caution:
In regions with input power above 240 VAC, a step-down transformer must be
installed to the system.
• Current: 15/7A.
• The grounded electrical outlet must connect to either a Euro or a US power cord plug
(provided in the Welcome Kit) and must be located within 2 m (80 inches) of the printer.
Caution:
A power cable is provided for connecting the printer to the AC electric source. Do not
use it with other equipment.
Operation of the printer outside this range is not recommended; degradation of performance
and shortened component life expectancy will be experienced. Facilities who are unsure of
their power quality should contact their service provider.
Caution:
Do not use an extension cord or power strip; doing so can result in intermittent power
issues. Connect the power cord directly into the receptacle.
Workstation Requirements
For GrabCAD Print workstation requirements please visit:
http://help.grabcad.com/article/195-system-requirements-for-grabcad-print.
While on the GrabCAD website, be sure to join the F120 GrabCAD community.
LAN Requirements
If utilizing a LAN connection for communication and file transfer functions, the LAN connection
is a 100 base T, Ethernet protocol, RJ45 connector. One 15 foot (4.57 m) CAT6, 10/100 base T
cable is supplied with the printer, located in the Welcome Kit. The printer will function in either
DHCP or Static IP configurations.
A LAN connection is not required however, as the printer is also capable of file transfer via a
Wi-Fi connection or a USB flash drive plugged into either of the printer’s USB ports. See the
F120 User Guide for detailed information and instructions on transferring files to the printer.