Stuv 6 Series User manual

STUV 6 (76 X 55 MODEL)
SPECIFICATIONS &
MANUFACTURER
INSTALLATION
GUIDE
^^

PAGE 2 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
Congratulations on your purchase of the STUV 6. This appliance should be installed and checked by a qualified
professional. Ensure you have read the operation guidelines thoroughly prior to first use.
CAUTION:
Using components or parts other than those provided by the manufacturer or modifying the specification of
components may result in inferior or unsafe operation.
WARNING:
• The appliance and flue-system must be installed in accordance with AS/NZS 2918 and the
relevant building code or codes.
• Any modification of the appliance that has not been approved in writing by the testing authority
will be in breach of the approval granted for compliance with AS/NZS 4013.
• Once the flue has been installed and approved by a professional installer, the flue must not be
modified in any way.

PAGE 3 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
DIMENSIONS & TECHNICAL DATA
STUV 6 - DIMENSIONS OF THE DEVICE WITHOUT THE DECORATIVE FRAME AND WITHOUT OPTIONAL EXTRAS
DETERMINED UNDER TEST CONDITIONS:
Nominal thermal output 6kW
Efficiency (Australian Test) 62%
Emissions (Australian Test) 0.6 g/Kg
WEIGHT AND DIMENSIONS:
Firebox external dimensions W722 x H538 x D413mm
Firebox weight 85Kg
Flue system Solid 6” or Flexi 6”
722
690
488101
228
353
413
713 mm
340
538476

PAGE 4 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
OVERVIEW
THE DEVICE
1Stove
2Support casing
CONNECTION TO THE COMBUSTION SMOKE OUTLET PIPE
3Smoke outlet connection piece (vertical or 45º angle)
FINISH
4Decorative frames
OPTIONS
5Stand
6Nozzle Ø100mm for external air inlet from the bottom
7Rear external air connection kit Ø100mm
1
5
6
7
3
2
4

PAGE 5 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
A
A
B
CD
E
G
F
BB
B
B
C
D
EF
Thin flush frame
Thin extended frame
DECORATIVE FRAMING OPTIONS
THIN FLUSH FRAME (mm)
THIN EXTENDED FRAME (mm)
A *B C D E F
Stuv 6 – 76 x 55 760 4550 317 414 67
*Expansion joint that must be respected around the decorative frame
A B C D E F G
Stuv 6 – 76 x 55 760 722 550 528 250 67 414

PAGE 6 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
DECORATIVE FRAMING OPTIONS
FITTED FRAME 4 SIDES (mm)
FITTED FRAME 3 SIDES (mm)
A B C D E F G
Stuv 6 – 76 x 55 794 744 586 536 316
(-0/+20)
413
(-0/+20)
60
(-0/+20)
A B C D E F G
Stuv 6 – 76 x 55 796 746 567 545 316
(-0/+20)
413
(-0/+20)
60
(-0/+20)
A
CD
E
F
G
B
Applied frame 4 sides
A
CD
F
G
E
B
Applied frame 3 sides

PAGE 7 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
6” FLUE AND 100MM AIR INTAKE CONNECTIONS
mm
A 149
B 29
C 262
D 345
E 150
mm
A 555
B 251
C 345
D 150
A
A
B
B
C
C
D
D
E
Dimensions of the smoke outlet at 45°
Dimensions of the smoke outlet upwards

PAGE 8 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
6” FLUE AND 100MM AIR INTAKE CONNECTIONS
mm
A 92
B 31
C 100
D 295
A
B
C
D
Dimensions of the connection to the external air inlet at the rear
mm
A 59
B 290
C 100
D 345
ABCD
Dimensions of the connection to the external air inlet at the bottom

PAGE 9 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
ADJUSTABLE FIREBOX STAND
mm
A 300
B 95
C 50 to 600
D 696
A
C
B
Dimensions of the stand
D

PAGE 10 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
2.2 FRAMING CLEARANCES
Stuv 6 is a zero clearance box to masonry. Allowing a small expansion gap is recommended to
prevent possible damages to the firebox or surrounding materials.
IMPORTANT: The fireplace is not load bearing
With Silicate Board (40mm)
Without insulative board
MASONRY INSTALLATION
CLEARANCES TO COMBUSTIBLE MATERIAL
Timber stud
Timber stud
Combustible back wall
Combustible back wall
40mm silicate board
40mm silicate board
FRONT
FRONT
SIDE
SIDE
20mm air gap
400mm 150mm400mm
75mm air gap
10mm air gap10mm air gap

PAGE 11 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
FLOOR PROTECTOR
Any combustible floor beneath a fireplace must have a floor protector that also extend in
front of the appliance.
If the fireplace is installed on a concrete, masonry or non combustibe floor there is no
requirement for a floor protector.
Floor protector must be minimum 30mm thick cement sheet (excluding non combustible floor finish)
Floor protector must be minimum 9mm thick cement sheet (excluding non combustible floor finish)
COMBUSTIBLE FLOOR INSTALLATION - FIREBOX IS INSTALLED BELOW 400MM HEIGHT
COMBUSTIBLE FLOOR INSTALLATION - FIREBOX IS INSTALLED AT 400MM HEIGHT OR ABOVE
550mm
965mm
760mm
300mm
30mm cement sheet
9mm cement sheet
Combustible floor
Combustible floor
399mm or lower
400mm or higher
Finished non combustible floor
Finished non combustible floor
1030mm
1030mm
550mm
300mm

PAGE 12 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
SETTING UP THE CONNECTIONS
The STUV 6 is specifically designed so that it is easy to connect to outside air intake (optional) and smoke outlet
(flue). The connections are carried out from the inside of the unit once fitted.
So before fitting the unit, prepare the connections as per below:
Install the flexible or solid flue so that is comes out close to where the appliance outlet will be located. Attach the
smoke outlet connection provided with the fireplace (if using a flexi flue, use a metal duct clamp - not provided).
OUTSIDE AIR INTAKE - REAR OR BACK (OPTIONAL)
FLUE
23
1
3
21
23
1
3
21
Install the air inlet duct and attach the nozzle with a metal duct clamp.

PAGE 13 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
GETTING THE UNIT READY FOR INSTALL
Dismantling the unit allows an easier handling process and give access to the different connections
STEP 1: DISMANTLE THE DOOR
STEP 2: REMOVE THE SMOKE DEFLECTORS
2
23
3
33
1
14
13
3
2
2
2
3
3
3
3
1
1
4
13
3
2
2
2
3
3
3
3
1
1
4
13
3
2

PAGE 14 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
GETTING THE UNIT READY FOR INSTALL
STEP 3: SEPARATING SUPPORT CASING & COMBUSTION CHAMBER
21
23
5 6
8
2
3
3
3
1
4
7
1
Stûv 6 - installation [en] - 0420
Separating from the support casing
Convection ducts (optional)
In practical terms
Flexible pipes for the hot air outlet are
attached to the nozzle using a collar
clamp.

PAGE 15 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
THREE OPTIONS FOR COMBUSTION AIR SUPPLY
OPTION #1: BOTTOM CONNECTION
OPTION #2: REAR CONNECTION
5
4
23
1
2
13
5
4
3
2
1
5
4
231
2
13
5
4
3
2
1

PAGE 16 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
THREE OPTIONS FOR COMBUSTION AIR SUPPLY
If you choose to get the air for combustion through the frame make sure you follow these simple steps:
1. Remove the head
from the Damper.
2. Remove the 2
side screws.
3. Remove the 2 plates and
the spring.
4. Put the Damper Head
back on.
OPTION #3: THROUGH THE FRAME
5
4
231
2
13
5
4
3
2
1
5
4
231
2
13
5
4
3
2
1
5
4
231
2
13
5
4
3
2
1

PAGE 17 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
POSITIONING THE OUTER CASING
OPTION #1: OUTER CASING INSTALL IN A RECESS
OPTION #2: OUTER CASING INSTALLED ON ITS STAND
23
1
Xmm
Y
600-X mm = Y
12
50-200mm
min. 50mm
78
3
3
4
3
56
911
10
23
1
Xmm
Y
600-X mm = Y
12
50-200mm
min. 50mm
78
3
3
4
3
56
911
10

PAGE 18 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
REASSEMBLING THE COMBUSTION CHAMBER IN THE OUTER CASING
2
1

PAGE 19 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
CONNECTING THE FLUE
123
45
Hold the smoke outlet connector (which has already been connected to the duct) by the handle
and attach it to the stove [figures 1 & 3]
Once the smoke outlet is in position, use pliers to break the handle off [figures 4 & 5].
N.B.: The smoke outlet can be turned to make it easier to connect to the duct [figure 2].

PAGE 20 STUV 6 | SPECIFICATIONS & MANUFACTURER INSTALLATION GUIDE
^
FITTING THE DECORATIVE FRAME
OPTION #1: FITTING THE THIN FRAME
OPTION #2: FITTING THE ADJUSTABLE 3 OR 4 SIDED FRAME
2
4
1
3
5
1
2
4
1
3
5
1