Sumake CB-32A User manual

PNEUMATIC BOTTOMER
PNEUMATIC TOOLS
MODEL:
MANUAL
WARNING
BEFORE OPERATING THIS STAPLER, ALL OPERATORS
SHOULD STUDY THIS MANUAL. TO UNDERSTAND AND
FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH THE STAPLER FOR FUTURE
REFERENCE. IF YOU HAVE ANY QUESTION, CONTACT
WITH YOUR DISTRIBUTOR.
CB-32A(34A)(35A)-I-0912B-CJ
CB-32A, CB-34A, CB-35A

2
TOOL SPECIFICATIONS
.MODEL OF TOOL ............................................................
.DIMESTIONS (LENGTH X HEIGHT X WIDTH) ................... 830MM X 600M X 1245MM
.WEIGHT ( WITHOUT FASTENERS) .................................. 23.7 KG
.AIR INLET ......................................................................... 1/4” NPT
.COMPRESSED AIR:
.MAXIMUM PERMISSIBLE OPERATING PRESSURE ........ 8 KG/CM
.RECOMMENDED OPERATING PRESSURE ................... 5 KG/CM ~ 6KG/CM
.STAPLES SPECIFICATION................................................. CROWN
LENGTH 15MM, 18MM, 22MM
.STAPLES CAPACITY ....................................................... 200 PCS
THE NOISE LEVELS: (AT THE WORKPLACE ALWAYS WEAR HEARING PROTECTION
EQUIPMENT.)
A – WEIGHTED SINGLE – EVENT SOUND PRESSURE LEVEL AT OPERATOR’S POSITION :
L pA, Is = 89 Dba
A – WEIGHTED SINGLE – EVENT SOUND POWER LEVEL :
L WA, Is = 93 Dba
A – WEIGHTED SINGLE – EVENT SURFACE SOUND PRESSURE LEVEL:
L Pa, Is, Im = 80 Dba
SAFETY INSTRUCTTIONS
DANGER
1. READ THIS MANUAL AND UNDERSTAND ALL SAFETY INSTRUCTIONS BEFORE
OPERATING THE TOOL IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT WITH OUR
AUTHORIZED REPRESENTATIVES.
CB-32A, CB-34A, CB-35A

3
2. NEVER USE ANY TYPE OF FLAMMABLE GASE OR OXYGEN AS A POWER
SOURCE FOR THE TOOL USE FILTERED, LUBRICATED, REQULATED
COMPRESSED AIR ONLY.
3. NEVER USE GASOLINE OR OTHER FLAMMABLE LIQUIDS TO CLEAN THE
TOOL. VAPOR IN THE TOOL WILL BE IGNITED BY A SPARK AND CAUSE THE
TOOL TO BE EXPLODED.
4. DO NOT EXCEED MAXIMUM PERMISSIBLE OPERATING PRESSURE OF THE
TOOL (8 KG/CM²)
5. DISCONNECT THE TOOL FROM AIR SUPPLY BEFORE CLEANING JAMS,
SERVICING, ADJUSTING, AND DURING NON – OPERATION.
WARNING
6. AT THE WORKPLACE, ALWAYS WEAR THE PROTECTIVE EQUIPMENT SUCH
AS SAFETY GLASSES, HEARING PROTECTION AND HEAD PROTECION.
7. DO NO USE A CHECK VALVE OR ANY OTHER FITING WHICH ALLOWS AIR
TO REMAIN IN THE TOOL.
8. DO NOT PLACE YOUR HAND OR ANY PART OF YOUR BODY IN THE STAPLE
CLINCHING AREA, BETWEEN COVER A (016) AND MOLD (046)
LUBRICATION AND MAINTENANCE
DISCONNECT THE AIR SUPPLY FROM THE TOOL BEFORE LUBRICATING, OR
SERVICING THE TOOL.
NOTE
YOUR TOOL REQUIRES LUBRICATION BEFORE YOU USE IT FOR THE FIRST TIME.

4
ASSEMBLY AIR BOTTOMER
1. FIND A SUITABLE PLACE.
2. OPEN THE PACKING AND STAND THE MACHINE UP.
3.USE 6 MM HEX. WRENCH AND 13 MM SPANNER TO ASSEMBLE THE BALANCER
(049).
NOTE : LET THE BALANCER (049) BE GOOD BALANCE ON THE LAND.
4. USE 17MM SPANNER TO ASSEMBLE THE “DOUBLE SCREW TUBE” (525) WITH
CYLINDER SET (035).
5. USE 19MM SPANNER TO ASSEMBLE THE “PU PLUG” (523) WITH CYLINDER SET
(035).
6. CONNECT THE AIR SOURCE, THEN YOU CAN USE THE BOTTOMER.
NOTE : CONTROL THE AIR PRESSURE BETWEEN 5 KG/CM²AND 6 KG/CM²
ADJUSTMENT THE SPEED
1. QUICK EXHAUST (529) CONTROL THE DRIVER’S SPEED.
2. FIX THE QUICK EXHAUST (529) WHEN THE OPERATING SPEED YOU LIKE.
OPERATING THE AIR BOTTOMER
1. PULL PUSHER (026) BACKWARDS UNTIL IT STOPS ON PUSHER PIVOTS (024).
THEN ROTATE PUSHER (026) INTO POSITION.
2. INSERT 4 STICKS OF APPROPRIATE STAPLES INTO THE MAGAZINE (020) FROM
BACK. LET THE STAPLES SLIDE FORWARD TO THE FRONT OF THE MAGAZINE
(020).

5
3. PULL PUSHER (026) BACK TO UPRIGHT POSITION AND GENTLY LET THE
PUSHER (026) SLIDE FORWARD AGAINST THE STAPLES. DO NOT LET
THE PUSHER (026) SLIDE FORWARD TO ENGAGE STAPLES AT HIGH
SPEED OR IT MAY DEFORM THE STAPLES OR DAMAGE THE MACHINE.
NOTE : KEEP SPRING (028) CLEARLY AND DON’T BEND THE SPRING
(028).
4. PUT THE CARTON INTO POSITION.
NOTE : STRAIGHT THE CENTER LINE OF CARTON TO THE COVER A’S
(016) CENTER LINE.
5. PRESS THE SWITCH (038) DOWN BY FOOT UNTH, IT STOPS. THEN
RELEASE THE SWITCH (038).
NOTE : IF THERE IS NOT A CARTON IN POSITION, DO NOT PRESS THE
SWITCH (038) DOWN.
CLEARING A JAM
1. PULL THE PUSHER (026) BACKWARDS AND ROTATE INTO POSITION.
THEN REMOVE THE REST OF THE STAPLES.
2. REMOVE COVER A (016) WITH 4 MM HEX. WRENCH.
3. CLEAR THE JAM.
4. ASSEMBLE COVER A (016).
NOTE : DISCONTACT THE AIR SOURCE, WHEN CLEARING A JAM.

CB-32A, CB-34A, CB-35A
PNEUMATIC BOTTOMER CROWN 32MM(34MM)(35MM)
CB-32A(34A)(35A)-P-1606C-CJ

CB-32A, CB-34A, CB-35A
PNEUMATIC BOTTOMER CROWN 32MM(34MM)(35MM)
PARTS LIST
No. Parts No. Description Q'ty No. Parts No. Description Q'ty
001 CB35A-001 Link 1 2 046 CB32A-046 Mold [For CB-32A] 1
002 CB35A-002 Tube 2 049 CB35A-049 Balancer 1
003 CB35A-003 Shaft E 2 050 CB35A-050 Link 3-C 2
004 CB35A-004 Link 2 2 501 CB35A-501 E-Ring [Φ10] 2
007 CB35A-007 Driver Seat 1 502 CB35A-502 E-Ring [Φ5] 2
008 CB35A-008 Shaft C 2 503 CB35A-503 E-Ring [Φ5] 2
CB35A-009 Driver [For CB-35A] 1 504 CB35A-504 Hex.Soc.Hdless.Bolt (M4x0.7-10) 2
CB32A-009 Driver [For CB-32A] 1 506 CB35A-506 Spring Pin (Φ6-16) 2
CB34A-009 Driver [For CB-34A] 1 507 CB35A-507 E-Ring (Φ6) 2
010 CB35A-010 Spring 2 508 CB35A-508 Hex.Soc.Hd.Bolt (M5x0.8-10) 6
011 CB35A-011 Spring Shaft 2 511 CB35A-511 Hex.Soc.Hd.Bolt (M5x0.8-8) 6
CB35A-012 Magazine Seat [For CB-35A] 1 512 CB35A-512 Lock Nut (M4x0.7) 1
CB32A-012 Magazine Seat [For CB-32A] 1 513 CB35A-513 Hex.Soc.Flat Counter Snk Hd.Screw (M4x0.7-20) 1
CB34A-012 Magazine Seat [For CB-34A] 1 516 CB35A-516 Hex.Soc.Flat Counter Snk Hd.Screw (M5x0.8-20) 2
014 CB35A-014 Cover B 1 517 CB35A-517 Lock Nut (M5x0.8) 2
015 CB35A-015 Shaft D 1 518 CB35A-518 Spring Pin (Φ4-16) 1
016 CB35A-016 Cover A 1 519 CB35A-519 E-Ring (Φ10) 2
017 CB35A-017 Bracket 1 520 CB35A-520 E-Ring (Φ10) 2
CB35A-020 Magazine Unit [For CB-35A] 1 521 CB35A-521 E-Ring (Φ10) 2
CB32A-020 Magazine Unit [For CB-32A] 1 523 CB35A-523 PU Plug (3/8"xΦ12-90°)1
CB34A-020 Magazine Unit [For CB-34A] 1 524 CB35A-524 PU Plug (3/8"xΦ12-90°)1
021 CB35A-021 Bracket Set 1 525 CB35A-525 Double Screw Tube (3/8"x3/8") 1
022 CB35A-022 Nut 2 526 CB35A-526 Hex.Soc.Hd.Bolt (M8x1.25-20) 2
023 CB35A-023 Right Pusher Guide 1 528 CB35A-528 Lock Nut (M8x1.25) 2
024 CB35A-024 Rod 2 529 CB35A-529 Quick Exhaust (3/8") 1
025 CB35A-025 Left Pusher Guide 1 CB35A-530-A Air Plug [Japan Type] 1
CB35A-026 Pusher Set [For CB-35A] 1 CB35A-530-B Air Plug [U.S.A. Type] 1
CB32A-026 Pusher Set [For CB-32A] 1 CB35A-530-C Air Plug [Europe Type] 1
CB34A-026 Pusher Set [For CB-34A] 1 531 CB35A-531 Spring Washer (Φ12) 1
027 CB35A-027 Roller 1 532 CB35A-532 PU Plug (1/4"xΦ12-90°)1
028 CB35A-028 Spring 1 534 CB35A-534 Washer (Φ5.1xΦ12xΦ0.8T) 2
029 CB35A-029 Link 3-A 2 535 CB35A-535 Flat Head Screw (3/16" UNC) 3
030 CB35A-030 Tube 1 536 CB35A-536 Deflector (3/8") 2
031 CB35A-031 Tube 2 537 CB35A-537 Nut (3/16" UNC) 3
032 CB35A-032 Shaft K 1 538 CB35A-538 PU Plug (3/8"x12-90°)3
033 CB35A-033 Shaft F 1 539 CB35A-539 Hex.Soc.Round.Hd.Screw (M4x0.7-8) 2
034 CB35A-034 Tube 2 540 CB35A-540 Wave Washer (Φ16.5xΦ23) 2
035 CB35A-035 Cylinder Set 1 541 CB35A-541 Tube (Φ8xΦ12x130cm) 1
036 CB35A-036 Shaft M 1 542 CB35A-542 Tube (Φ8xΦ12x145cm) 1
037 CB35A-037 Switch Cover Unit 1 543 CB35A-543 Tube (Φ8xΦ12x120cm) 1
038 CB35A-038 Switch 1 544 CB35A-544 Spring Pin (Φ4x12) 4
039 CB35A-039 Body Set 1 545 CB35A-545 E-Ring (Φ15) 2
046 CB35A-046 Mold [For CB-34A(35A)] 1
CB-32A(34A)(35A)-P-1606C-CJ
009
020
026
530
012

NOTE
www.SUMAKE.com
www.AIRCOMPRESSOR.com.tw