Summer 12130B User manual

4
INSTRUCTION MANUAL
SURE & SECURE®
SINGLE BEDRAIL
Please read the following instructions
and warnings carefully.
Keep this instruction manual
for future reference.
Adult assembly required.
For Technical Support Call
1-800-268-6237 or E-Mail at
customerser[email protected].
For use with children 2-5 years of age.
SET UP:
TO FOLD DOWN BEDRAIL:
Raise locking pins up on both
sides of the bedrail’s support
leg and fold down bedrail
(Figures P & Q).
QP
TO CLEAN:
To clean this Sure and Secure Single Bedrail, surface wash with damp sponge, mild soap and
cold water. Rinse and lay flat to dry. Do not remove fabric cover from frame.
TO LOOSEN BEDRAIL FOR REMOVAL:
Push release lever up on support leg while pulling
bedrail away from mattress. Repeat on other
end (Figure R).
CAUTION: Do not push strap lock lever down.
R
IMPORTANT NOTE: To Ensure
against entrapment hazards, make
sure there are no gaps between the
bedrail and the mattress. Slight
deformation of the mattress is
acceptable. See diagram at right.
Summer Infant, Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
1-800-268-6237
© 2007 Summer Infant, Inc.
Please retain information for
future reference.
Summer Infant Europe, LTD.
Office Suite 6, Second Floor
Bournehall House, Bournehall Road
Bushey, Hertfordshire WD 23 3HP
[phone]
Colors and styles may vary.
MADE IN CHINA 6/09
mattress
box spring
12130B/12135B/12150B
(colors & styles may vary)
www.summerinfant.com
We LOVE our customers!
Get to know us at:
We at Summer Infant stand behind all of our products. If
you are not completely satisfied or have any questions,
please contact our customer service department at
1-800-268-6237 or [email protected]
(For Europe call [phone] or
[email protected])
Suffocation and Strangulation Hazard. Death or Serious Injury Can Occur:
• Infants who cannot get in and out of an adult bed without help can be trapped
between a mattress and a wall and suffocate. NEVER place infants in adult beds
with or without bedrail.
• BEDRAIL USE: Bedrail can trap young children against mattress, headboard, or footboard.
• Use only for children who have outgrown a crib. NEVER use in place of a crib.
• Use only with children who can get in and out of adult bed without help.
• ALWAYS keep bedrail pushed firmly against mattress and at least 9 inches from
headboard and footboard.
• NEVER use on toddler bed, bunk bed, water bed, or bed with inflatable mattress.
Use only on adult bed with mattress and box spring or platform bed (support board 5/8"
nominal thickness).
• ENTRAPMENT HAZARD: Death or Serious Injury Can Occur if bedrail is used without
fabric cover. Never use without fabric covering metal frame.
• Discontinue use if damaged,broken, or if parts are missing.
Periodically check the bedrail for tightness to ensure bedrail is snug
against bed.

3
SET UP:
M
N
O
H
Headboard
Footboard
Bedrail Panel
At Least 9“ At Least 9“
2
FEATURES & COMPONENTS:
SET UP:
Step 1:
Insert top, middle and bottom connector
tubes into each end rail (Figure A).
Note: Top and bottom connector tubes
have pins on each side, and the pins snap
into end rails. Middle connector tube does
not have pins.
Step 2:
Insert support leg into end of bedrail
frame and snap into place (Figures B & C).
Take second support leg and repeat on
other side.
Step 3:
Fold down support legs as shown in
Figure D, until spring lock is engaged
(see Figure E).
Step 4:
Place fabric panel completely over bedrail
frame and slide down (Figure F).
Note: Assure that bottom rail is covered by
fabric panel.
Step 5:
Zipper bottom of fabric cover over bottom
rail to fasten. Attach hook & loop flap to
cover opening.
Step 6:
This bedrail fits twin, full and queen size
mattresses. Connect mattress anchors to
3-way connector on both sides by snapping
mattress anchor into place
(Figure H).
Note: Be sure to orient
the mattress anchor
with notch facing down
(Figure G).
A
BC
F
Lock
engaged
Lock
pin
D E
press
button
Step 7:
Attach strap clip to 3-way connector (with notch facing down)
(Figure I).
Step 8:
Remove mattress from bed.
Step 9:
Position assembled bedrail on boxspring. While holding the
release lever on bottom corner of bedrail, pull the strap to
proper tension until snug against boxspring (Figure J).
Repeat on the other end of the bedrail.
Step 10:
Place mattress back on box spring. Pull the strap to proper
tension until tight against mattress (Figure J).
NOTE: Press release lever down when strap is tight to lock
strap in place (Figure K). Roll up excess strap and tuck under
mattress (Figure L).
Step 11:
Ensure the bedrail is centered on the mattress end to end.
Using enclosed template, measure AT LEAST 9 inches
between the ends of the bedrail and the headboard and
footboard (Diagram M).
TO CONNECT 2 SINGLE BEDRAILS
TO CREATE A DOUBLE BEDRAIL
Step 1:
Remove 3-way connector from mattress anchor
by pressing button with a pen or screwdriver (Figure N).
Step 2:
Rotate 3-way connector and connect
2 single bedrails under mattress
(Figure O).
Step 3:
Follow steps 7 through 8 to finalize
installation of double bedrail.
Bedrail Frame
(3 connector tubes
& 2 end panels):
Fabric Panel:
Fold-down
Support
Leg (two):
Mattress
Anchor
(two):
3-way
Connector (two):
9“ Template: 987654321
J
Release Lever
L
K
Tuck excess strap
under mattress
I
G
Mattress
side
Box spring
side
no pins
pins
pins
Mattress