Suncast BMCCPD7204 User manual

© 2018 Suncast Corporation, Batavia, IL 0361365C
To learn about other Suncast products, please call
1-855-477-1260 or 1-630-879-2050.
Product Feedback? Go To: Suncastcommercial.com/feedback
OR email us at: [email protected]
ITEM NUMBER: BMCCPD7204/BMCCPD7206/BMCCPD8004/BMCCPD8006
1/2”
F
HG
L
N
C
E
D
B
A
K
J
*Quantity of shelf (F) and support tube (L) will
vary by model.
PARTS
TOOLS NEEDED
DD
BB
AA CC
P

2
BEFORE YOU BEGIN
• Read instructions thoroughly prior to assembly.
This kit contains parts that can be damaged if assembled incorrectly or in the wrong sequence.
• Please follow instructions.
Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly.
• Check for all parts before you begin assembly.
Using the provided parts check list, verify that you have all the parts required to construct your cabinets.
• Assistance is required during parts of the assembly.
CAUTION
• Not intended for storage of flammable or caustic chemicals.
• Not intended for usage by children.
• To avoid risk of suffocation, do not allow children to play inside container.
• This product may become susceptible to impact damage in freezing temperatures.
• Do not store near excessive heat.
• Exercise caution when moving fully loaded product. This product is not intended for
transporting heavy objects. Use as a stationary storage device only.
• Do not sit or stand on top.
• Do not store items on top.
• Max load 200lbs. per shelf.
• Mounting to wall studs is recommended.
• Mount flush and level to wall.
• Do not stack units.
CARE AND CLEANING
Exposure to the elements (such as dust, plant and animal life, moisture and sunlight) encourages moss, algae, and mold to grow on
outdoor items. To maintain the look of your product, we recommend cleaning it each year with mild soap and water. DO NOT use bleach,
ammonia, or other caustic cleaners, and DO NOT use stiff bristle brushes. Failure to perform annual cleaning could result in permanent
staining of the plastic. This is not a manufacturing defect and is not covered under warranty.

3
1
2
1
C
AA
C
Smooth Side Up
1
2
3
2
D
D
B
C
Align tabs on left side panel (C) with slots on bottom panel
(A). Lower side panel into slots and lock in place by sliding
panel towards front. Repeat with right side panel (B).
Align and engage tabs on back panel (D) with slots on side
panels (C/B). Push panel D down to lock in place.
All tabs should be engaged before locking panels together in steps 1-3 .
1
2
3
C B
E
Align slots on top panel (E) with tabs on side panels
(C/B). Lower top panel and lock in place by sliding panel
towards front. Top will overhang front slightly.
ASSEMBLY

4
Attach support tube (L) to shelf (F) using four screws (AA).
Large hole of support tube must face out. Repeat for
remaining shelves.
Tab
4
L
F
L
AA
X4
Insert shelf (F) on angle. Move to a level position while holding
in hands.
Tab on shelf must engage with slot on inside panel for
each shelf. Push side panels inward to engage.
Tilt shelf (F) forward and place front corners of shelf into
indented area on side panels. Push down on back of shelf to
snap into position. Repeat steps for remaining shelves. Insert
middle shelf last.
SHELF INSTALLATION
5
F
2
1
6

5
Insert door latch housing (K) into top right door (G) and snap
into place. Insert door latch (J) into door latch housing. Push
latch pin down so it is fully seated in latch housing. Push
down with force until you hear a snap. Slide latch up and
down to confirm it slides properly.
Note: You may need a screw driver to push the latch pin
down. Push with force.
2
2
1
1
K
7
J
G
G
TOP OF DOOR HOUSING AND LATCH PIN
Before proceeding, please take notice of
teeth on housing that will face upward
when installed on top of right door.
DOOR ASSEMBLY

6
2
1
2
1
G
K
8
J
G
BOTTOM OF DOOR HOUSING AND LATCH PIN
Before proceeding, please take notice of teeth on
housing that will face downward when installed on
bottom right of door.
Insert door latch housing (K) into bottom right door (G) and
snap into place. Insert door latch (J) into door latch housing.
Push latch pin down so it is fully seated in latch housing.
Push down with force until you hear a snap. Slide latch up
and down to confirm it slides properly.
Note: You may need a screw driver to push the latch pin
down. Push with force.
ASSEMBLY - DOORS CONTINUED

7
ASSEMBLY - DOORS CONTINUED
9
H
H
H
1
2
With left door (H) in the open position, place door into hinge
receptacle on bottom left of cabinet. Insert hinge pin under top
panel and slide to the left into hinge receptacle. Repeat with right
door (G).
N
N
P
P
AA
x3
AA
x3
10
Snap hinge part (P) onto hinge part (N) as shown. Attach hinge side
(N) to left side panel (C) using three screws (AA). Attach hinge side (P)
to left door (H) using three screws (AA). Repeat on right side.
BB
Drill Here
1
x2
BB
CC
D
x2
DD
Using a 1/2˝drill bit, drill through the two provided loca-
tions on Back Panel (D). Place cabinet in desired loca-
tion. With a pencil mark the hole locations on the wall,
and drill through the wall with 1/2˝ drill bit.
Close toggle bolt before putting through 1/2˝ hole or it
will not fit. Wings on toggle bolt need to be positioned
toward the end of the bolt.
While holding cabinet in place, put toggle bolt through
drilled holes in cabinet and wall. Tighten screws to
secure to wall.
Do not overtighten as damage to product may occur.
Securing cabinet to wall is easier with shelves removed.
With doors closed, attach a 5/16˝ lock (not provided).
SECURING CABINET TO WALL - Mounting to wall is recommended and hardware is provided.

8
Warranty
SUNCAST COMMERCIAL®ONE Year Limited Warranty
Your SUNCAST COMMERCIAL® item has a ONE YEAR LIMITED WARRANTY against product failure resulting
from defects in manufacturing or materials. The warranty period starts on the delivery date. Incidental and
consequential damages are not covered.
Warranty Claims
To file a warranty claim contact the manufacturer, SUNCAST®CORPORATION, 701 North Kirk Road, Batavia,
Illinois, 60510. Call toll free [phone] or visit www.suncastcommercial.com. SUNCAST®will replace
only the parts that failed under the terms of the warranty. In some cases, the replacement parts may
not be identical, but they shall be of equal or greater performance than the original part. We require proof
of purchase. We require evidence of the failure. Warranty excludes shipping and handling charges.
WARRANTY LIMITATIONS
THIS WARRANTY COVERS ONLY DEFECTS THAT AFFECT THE FORM, FIT OR FUNCTION OF THE UNIT.
It excludes natural aging of the unit, discoloration, ordinary wear and tear, ordinary weathering, sunlight fading,
or rust. It excludes staining caused by mold, mildew or tree sap and damage caused by animals including
insects, vermin or houshold pets. The warranty does not cover damage caused by Acts of Nature including
but not limited to: wind in excess of 50 mph; tornado; hurricane; microburst; hail; flood; blizzard; extreme heat;
pollution or fire events.
The following actions void the warranty: improper assembly; use above intended and reasonable capacity;
misuse; abuse; failure to perform ordinary maintenance. Modification of the original product voids all warranties.
Suncast assumes no liability for any modified product or consequences resulting from failure of a modified
product.
Suncast is not responsible for: loss of use of the unit; labor for repair, inspection fees or disposal costs.
THIS WARRANTY IS NONTRANSFERABLE. IT EXCLUDES FLOOR MODELS, CLEARANCE AND OPEN
BOX UNITS.
THE MANUFACTURER’S LIABILITY HEREUNDER IS LIMITED SOLELY TO THE REPLACEMENT OF THE
DEFECTIVE PRODUCT OR PART AND THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM ANY DEFECT IN MATERIAL
OR WORKMANSHIP OR FROM THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages; the limitation or
exclusion may not apply to you.