Sunlighten Amplify II User manual

2x Full Spectrum (FS) Heater
1x Floor
1x Bench
J2x FS Heater Covers LK 2x FS Heater Top Panel M
4x FS Heater brackets
N
1x Right Wall
G
1x Back Wall
F1x Left Wall
I
1x Front Wall with glass panel
H
1x 1x5x
A B C 1x Roof
D E
12 1x
Allen wrench
812x 912x 10 12x 712x 2x 11
2x
1 2 5x 34x 44x 58x 612x
UK ASSEMBLY INSTRUCTIONS Amplify II
1 sunlighten.com/gb-en

Attach the feet pegs with supplied Allen wrench
and bolts to the underside of floor .
NOTE: Make sure the floor panel is on a surface that
is perfectly level and relatively smooth.
2 E
A
Unpack each wall segment from the shipping material. Stage each
wall segment in the room you will be assembling the unit.
STEP 1
Place the back wall on the back of the floor panel .
Be sure you have two people assisting with this step.
This is the side with the sauna information label
on the bottom edge.
STEP 2
PRE-STEPS
A
2
12
1
F E
230V,21000 watts.
3m cord exits from back left of roof.
See USER MANUAL or spec sheet for
additional specs.
E
E
E
F
2 sunlighten.com/gb-en

STEP 3
As you insert each wall segment, you will insert the
U-clips in the pre-drilled holes in the corner .
This will keep the walls sealed together.
The front wall will be inserted next. Be careful of the
glass door and panel as you insert the wall.
Place right wall on the right side of floor panel .
This wall panel should sit flush once properly seated.
Make sure no gaps are visible in the corner of the two
walls as you insert it. It should be inserted flush.
STEP 4
H
GE
3
3
G
H
E
3 sunlighten.com/gb-en

STEP 5
Once all the U-clips have been inserted in the
corners, the next step will be to place the roof
on top. Make sure the side with the main power
cord receptacle faces the back.
After securing the U-clip , the left wall will be
the last to be inserted. Make sure it is flush and no
gaps are showing in the corners.
NOTE: If you ever have trouble getting a U-clip to
slide in, this can be resolved by tapping it with a
hammer.
STEP 6
3I
3
3
3
D
I
D
4 sunlighten.com/gb-en

STEP 7
Please make all connections on roof of sauna as illustrated.
STEP 8
Before the bench is placed, make
sure the heater frames are taken out to
allow the bench to be placed on its
support.
Left Wall Heaters
Full Spectrum Heater
Back Heater/Speakers
Right Wall/ Floor Heaters
Control Panel
Full Spectrum Heater
J
heater frame
heater frame
C
B
1
12
J
11
With the bench installed, the heater panel
frames can be inserted back into their
respectable walls.
The door handles come with the hardware
and can easily be screwed right in.
Asecond person should hold the handle
while the other screws the bolts in with the
Allen wrench. The dust cover should also be
replaced.
5 sunlighten.com/gb-en

STEP 9
Connect 2 brackets to the back of the Full
Spectrum heater .
STEP 10
Connect the cable at the base of the Full Spectrum
heater to the socket at the base of the inside
front wall.
STEP 11
Fix both brackets attached to Full Spectrum
heater on either side of heater into pre-drilled
holes on front right inside corner sauna walls.
Repeat Steps 9-11 for the second FS Heater on
front left inside corner sauna walls.
N
K8
12
9
6
12
N
K
8
9
6
N
KK
6 sunlighten.com/gb-en

L
STEP 12
Place FS Heater Cover to the Full Spectrum heater
by securing into pre-drilled holes in floor panel .
STEP 13
L
K
Insert into pre-drilled holes on walls for the FS heater top panel .
Screw into pre-drilled holes to secure brackets.
5
4
N
5
L
5
4
STEP 14
Add FS heater top panel to both FS heaters.
N
N
7 sunlighten.com/gb-en

CONGRATULATIONS, your sauna is now ready to enjoy!
If you have any questions, please call
Sunlighten Customer Support at 0330.808.1203.
STEP 15
10
7
04272022
STEP 15
Make sure that screws and washers are fully
secure in their pre-drilled holes using a Phillips
screwdriver.
710
8 sunlighten.com/gb-en