Sunlighten mPulse Discover User manual

ASSEMBLY INSTRUCTIONS
included in door handle
4x
7x 2x 2x 2x
1 2 3 5 6 7
8x 5x 4x 1x 1x
M6x70
Allen wrench Philips Screw Driver
47x
M6x55
A B C D
1x Roof
1x Back Wall
1x Left Wall
1x Bench
1x Right Wall
1x Front Wall
2x Glass Doors
E1x Floor F
G
I
K
J
L
H
UK ASSEMBLY INSTRUCTIONS Discover
1sunlighten.com.au 1sunlighten.com/gb-en

G
F
The first step to installing your new sauna
will be to insert the legs underneath the
floor panel. The holes are already pre-drilled
so all you need are the bolts and the
Allen wrench . This is necessary to allow
air circulation to flow underneath and
maintain the integrity of the unit. After legs are
in place, please turn floor panel 180° so the back
of the sauna connects with the back wall
as shown below.
4
6
STEP 1
Before you begin installing the walls, be sure you
have at least:
• 15cm between the back of the sauna and the
outlet wall.
•30 cm gap from the top of the sauna to the ceiling.
•Place the sauna next to the wall power outlet to
ensure you have access to the wall power socket
outlet to cut the power to the unit if required.
Unscrew the screws holding the floor covers at the
rear of the floor.Then remove the floor covers (take
care not to step on the electrical components).
Make sure the floor panel is placed on a surface that
is relatively smooth and perfectly level. Failure to do
so can cause the door to not close all the way in the
later steps.
In this step, make sure one person is holding the
wall while the other helps balance it and press it in
place.
STEP 2
PRE-STEPS
230 V, 4200 W
Requires hard-wired dedicated outlet.*
3m cord exists from back left of base.
G
6sunlighten.com.au 2sunlighten.com/gb-en
* Failure to do so will void your sauna's warranty
and customer will assume liability for any electrical
damages to the sauna itself or the residence/business
in which the sauna is installed.
See USER MANUAL
Unpack each wall segment from the shipping material, stage each
wall segment in the room you will be assembling the unit.
Remove the internal wooden heater frames during unpacking
of the wall segments, set these aside for installation after
the sauna is assembled.
Remove the small wooden wire covers at the base of each vertical
wall segment, set aside for placement after sauna is assembled.
Back of sauna
Front of sauna
F
A
4
6
B
Back of sauna

HI
STEP 3 STEP 4
The front wall will be the last to install.
There will be wire connections that need to be made
at the base of each wall panel. These can be accessed
by small hatches on the walls (floor hatch for the
front). If a cable gets stuck in the floor it can be
accessed by removing the wood piece that covers
the powerbox.
A diagram showing the connection locations
can be found on STEP 8.
NOTE: If you ever have trouble getting
a U-clip to slide in, this can be resolved by
tapping it with a hammer.
The following walls will be inserted the same way
as STEP 2. Make sure the wires coming out from
the bottom hatches don’t pinch when you mount
the walls.
STEP 5
After you place each wall segement, please
use the U-clips and insert them in each
upper corner to hold the walls together.
5
J
J
6sunlighten.com.au 3sunlighten.com/gb-en
5
5

STEP 6
After all four U-clips are inserted
in the corners, the next step will be
to place the roof on top. The roof will also
reinforce the walls in position along with the clips.
NOTE: The roof may require some slight
manipulation to fall into place on top of
the wall panels.
STEP 7
5
6sunlighten.com.au 4sunlighten.com/gb-en
8
Lights, Blaupunkt/
Sound Therapy Receiver
D15
D16
E8
D17
After the roof is placed, remove the dust covers.
There should be the connections to the lights and
speakers at the top front. Connect those so you
can turn on the lights and listen to sound.
• Connect 3-pin rectangular plug (D15 – two red,
one white) into E5.
• Connect E5 to SP-Amp.
• Connect D17 RCA plugs (one red and one white)
to left side of SP-Amp.
• Leave D16 cable 4-pin, white rectangular
connector and second D15 3-pin rectangular
connector unplugged unless you purchased the
Sound Therapy Kit.
• If Sound Therapy was purchased, plug D15 and
D16 into E8.
• Plug E8 into SS-Amp.
E5
E
5
5

6sunlighten.com.au 5sunlighten.com/gb-en

STEP 8
Right Wall Heaters
Back Wall Heaters
Left Wall Heaters
6sunlighten.com.au 6sunlighten.com/gb-en
Front Wall Heaters,
Lights, Blaupunkt/
Sound Therapy Receiver,
Control Panel
K
K
The dust cover should be replaced to protect
the lights and speakers from dust and other
floating residue. As mentioned in STEP 5, there
are four connections to be made in each bottom
section of the walls. If you have not yet done so,
consult with the diagram at the bottom of this page.
After the four floor connections have been made,
replace the floor covers as mentioned in STEP 2,
then replace and install the bench . Make sure
the heater frames are not mounted, otherwise
they will prevent the bench from resting on the
supports. The large portion of the bench will go
in first, on the back wall support. Last will be the
small part which rests on the cutout of the large
bench piece, as well as the support against the
right wall. There will be two screws to screw into
the two holes on the corner where the two door
thresholds meet.
Now, place the heater frames in their
respective locations. NOTE: Look at
the back of the heater frames
for the “This Side Up”
sticker for proper orientation.

6
STEP 9
After the bench is placed in the unit, the next step
will be inserting the left glass door . Please
ensure you have at least one other person to assist
with this step. Do not put the door handles on as that
will be done in a later step after the door has been
safely attached in this step.
The hinges can be secured following instructions
given on Step 10 below.
NOTE: You can use a paint stick to shim the glass
door at a desirable angel above the threshold as
you mount it.
STEP 10
L
Using the Allen wrench , you will tighten the
bolts into the hinges as the door is inserted.
Make sure the bolt is inserted firmly. Each hinge will
have four plastic gaskets. The door will be inserted
between the four gaskets.
Make sure the rough-texture side of the gasket is
against the glass door as your insert it. This will give
it the grip needed to hang it. Likewise, make sure the
gaskets touching the hinges also are doing so by the
rough side.
6
L
6
L
L
6sunlighten.com.au 7sunlighten.com/gb-en

D
C
3
2
1
STEP 11
The gaskets, bolts and washers , and
will come with the handles. The washers need to be
inserted into the door holes first before the gaskets
go on and eventually the bolts. The rough side of the
gaskets must be facing the glass door. Be sure to
have a second person hold the handle in place while
the other inserts the bolt.
1 2 3
6sunlighten.com.au 8sunlighten.com/gb-en
CONGRATULATIONS, your sauna is now ready to enjoy!
If you have any queries, please call
Sunlighten Customer Support at 0330.808.1203.
10062023