Sunlighten Amplify III Configuration guide

Cabin Cleaning &
Maintenance
INSTRUCTION GUIDE

Cabin Cleaning and Maintenance | Page 1
1.
2.
3. 4.
CLEAN & MAINTAIN YOUR SUNLIGHTEN
Your Sunlighten deserves all the TLC you can give it. We’ve
provided these instructions to help you keep your sauna clean and
running well. Follow these instructions carefully and you’ll enjoy
your wellness oasis for years to come.
Your Cabin Cleaning Kit
(available at shop-us.sunlighten.com/) includes:
1. Natural Glass Cleaner
2. Natural Sauna Cleaner
3. 150-grit sanding (nishing) sponge
4. Microber cloth
How to Clean Sauna Wood
• Mix 1 oz of Natural Sauna Cleaner per gallon of warm or hot
water to dilute.
• Do not spray the wood directly. Spray the microber cloth (or
a soft cloth, not a paper towel) and dab stains.
• Can substitute distilled white vinegar, with an acid of 6% or
more, and water: 1 part distilled white vinegar to 2-3 parts
water. Do not use apple cider vinegar.
• Do not use chemical cleaners on the wood.
How to Clean Sauna Glass
• Sunlighten Glass Cleaner can be sprayed directly on glass.
• Do not use chemical cleaners on the glass.
• Wipe down with microber cloth.

Cabin Cleaning and Maintenance | Page 2
Sauna Cleaning Protocol
After each use
• Wipe down bench and oor with microber cloth from the Sunlighten Natural Cleaning Kit or a soft cloth.
• For any areas with moisture build-up, use a sponge to soak up excess moisture and microber towel or soft cloth to
dry.
Daily
• Wipe down bench, base, walls, and backrest with a microber towel or soft cloth.
• Use sponge to soak up any excess moisture from these areas.
• Open roof vent and/or door. Leave open overnight, or for at least 2 hours.
Weekly
• Lightly spray a microber towel or soft cloth to wipe down ALL wooden surfaces with the Natural Sauna Cleaner.
Never spray directly on your wood.
• After wood is dry, inspect for any areas of moisture or soil build-up.
• Use a (150 grit or higher) sanding/nishing sponge to lightly sand and clean those areas.
• Use Natural Sauna Cleaner on a microber towel or soft cloth to wipe down after sanding.
• Use the brush attachment of a vacuum to clean any debris or dust build-up from inside your unit and heater
surfaces.
Monthly
• Follow steps for weekly cleaning.
• While the sauna is off and cooled down, remove heater covers and wipe down heater surfaces with a microber
towel or soft cloth.
• For high trafc areas, such as the base near the front wall, it may be necessary to utilize an 80-grit sanding pad.
Follow these steps:
° Use 80-grit sanding sponge to remove any excess moisture or soil stains.
° Finish with 150-grit sanding/nishing sponge, provided in the Sunlighten Natural Cleaning Kit.
° Spray a microber towel or soft cloth with Natural Sauna Cleaner and then wipe down the wood.
Note: Glass cleaner should be used as often as needed.

Cabin Cleaning and Maintenance | Page 3
General Maintenance
• Use dry cloth to dust the exterior.
• Unplug the unit twice a year for at least 15 minutes.
• Drape towels over the bench to decrease sweat
accumulation.
• Do not cover more than 40% of the oor grate.
• Keep unit unplugged if unattended for long periods
of time (e.g., vacation).
• (mPulse specic) - Use can of spray air, similar to what
you would use on your computer, to clear out dust/
debris from the heat syncs on the power box twice a
year. (Heat syncs are the spike-looking objects on the
back side of the power box, which is found directly
under the bench beneath wooden covers)
Outdoor Units
• You must have a Sunlighten Sauna Cover installed per
the instructions, in order to place your unit outside; to
keep your warranty intact.
• Twice a year in mild, dry weather, remove the cover
to inspect for tears/holes/worn spots in the fabric and
plastic liner. If you nd tears/holes/worn spots, you will
need to replace your Sunlighten Sauna Cover.
• One to two times a year, make sure wires have not
been damaged by rodents or pests.*
• mPulse power box found directly under the bench
has a lot of wiring. There is also connection point
on the oor directly under the Android Control
Panel.
• Signature has a single stretch of wiring
immediately to the right of the oor grate. You will
have to slide a board out to get to the wiring.
*There is no oor heater for an Amplify - all of the
wiring is up within the roof panel and walls.
heat syncs
mPulse power box with
heat syncs
Signature wiring

CONTACT INFORMATION
Sunlighten, Inc. Global Headquarters
7373 W. 107th Street
Overland Park, KS 66212
877-292-0020
www.sunlighten.com/customer-care