Sunricher SR-ZGP2801K4-DIM User manual

70100059
Function introduction
Important: Read All Instructions Prior to Installation
Product Data
Switch Type
Transmission Range
Radio Frequency
Power Supply
Buttons
Dimensions
Operating Temperature
Working Humidity
Waterproof Grade
Warranty
DIM control
10-30m (typical)
2.4GHz (Zigbee channels 11-26)
Self-generated when switch is pressed
4
44.9x106.2x19.2mm
-20 ℃ ~ +45 ℃
10% ~ 95% RH non-condensing
IP20
5 years
• DO NOT expose the device to moisture.
Safety & Warnings
Product Description
The Zigbee green power switch is a wireless transmitter that communicates with a wide variety of Zigbee
compatible systems. The switch uses battery-free, energy-harvesting technology. Every time the switch is
pressed, a micro-generator produces a small electrical current that powers a built-in transmitter. This
transmitter sends wireless radio signals that are used to remotely control a compatible system.
Compatible With
Zigbee Green Power (included in Zigbee 3.0)
DIM Zigbee Green Power Switch
Front side
Back side
Short press to increase brightness by
10%,Press and hold to increase
brightness smoothly
Short press to decrease brightness by
10%,Press and hold to decrease
brightness smoothly
Short press to turn on paired devices
Short press to turn off paired devices
19.21 mm
44.9 mm
106.16 mm
83.2 mm
Operations
Pairing GP Switch to a Compatible Zigbee Light Device:
Step 1: activate learning to GP switch mode of the compatible light device (generally our light devices will
enter the mode by short pressing “prog.” or “reset” button 4 times, or by resetting power 4 times), please refer
to the manual of corresponding light device.
Step 2: put the GP switch into learning mode.
To enter into learning mode, start by selecting one button on the switch. (Use the same button for the entire
sequence, pressing any other button will exit the learning mode.)
Next, execute the following sequence:
1. Press and hold the selected button for over 10 seconds, and then release it.
2. Short press the button once, and then release it.
3. Press and hold the button again for over 10 seconds, and then release it.
The switch has now entered learning mode.
Wait for approximate 1 second to check whether there is indication on the light device for successful pairing,
generally our light device will blink twice to indicate successful pairing.
Exit learning mode on the switch by pressing any other button on the switch after pairing successfully.
Just ignore step 3.
If there is no indication, please continue executing step 3.

Channel ID
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Lower Frequency
2404
2409
2414
2419
2424
2429
2434
2439
2444
2449
2454
2459
2464
2469
2474
2479
Center Frequency
2405
2410
2415
2420
2425
2430
2435
2440
2445
2450
2455
2460
2465
2470
2475
2480
Upper Frequency
2406
2411
2416
2421
2426
2431
2436
2441
2446
2451
2456
2461
2466
2471
2476
2481
Step 3: Cycle through the sixteen Zigbee channels
A radio signal needs be sent from the switch to the compatible light device on the correct Zigbee channel, the
light device uses one of the sixteen possible channels, automatically set the device. Using the switch, a signal
will be sent on each channel until the channel used by the light device is found.
Upon entering learning mode, the signal will be sent by the switch on default channel 11. Please refer to the
following chart of the Zigbee channels and the corresponding radio frequencies (in MHZ).
Installation
Wallplate/Adapter purchased separately
If there is no indication on the light device for successful pairing, the signal sent by the switch is not on the
correct channel, we need to change the switch’s channel.
To change the switch’s channel, short press the selected button to move from default channel 11 to the
next one. For each such button press, the switch transmits on the next channel.
After each such button press, please wait for approximate 1 second to check whether there is indication on the
light device for successful pairing.
If pairing successfully, please exit learning mode on the switch. If channel 26 has been reached, but there is
still no indication, it might because the switch has not entered learning mode yet since the very start. We have
to repeat the step 2 to put it into learning mode.
Delete Pairing to a Paired Zigbee Light Device:
Step 1: activate delete learning to GP switch mode of the paired light device (generally our light devices will enter
the mode by short pressing “prog.” or “reset” button 3 times, or by resetting power 3 times), please refer to the manual of
corresponding light device.
Step 2: put the GP switch into learning mode.
To enter into learning mode, start by selecting one button on the switch. (Use the same button for the entire sequence,
pressing any other button will exit the learning mode.)
Next, execute the following sequence:
1. Press and hold the selected button for over 10 seconds, and then release it.
2. Short press the button once, and then release it.
3. Press and hold the button again for over 10 seconds, and then release it
The switch has now entered learning mode.
Wait for approximate 1 second to check whether there is indication on the light device to indicate that pairing is deleted,
generally our light device will blink 4 times, which means the pairing is deleted successfully.
Exit learning mode on the switch by pressing any other button on the switch after pairing deleted. Just ignore
step 3.
If there is no indication, please continue executing step 3.
Step 3: Cycle through the sixteen Zigbee channels
If there is no indication on the light device to indicate that pairing is deleted, the signal sent by the switch is not on the
correct channel, we need to change the switch’s channel.
To change the switch’s channel, short press the selected button to move from default channel 11 to the next
one. For each such button press, the switch transmits on the next channel.
After each such button press, please wait for approximate 1 second to check whether there is indication on the light
device to indicate that pairing is deleted.
If pairing deleted successfully, please exit learning mode on the switch. If channel 26 has been reached, but there is still
no indication, it might because the switch has not entered learning mode yet since the very start. We have to repeat the
step 2 to put it into learning mode.
Signal Repeating Function of the Compatible Light Devices
The compatible light devices can repeat the received wireless signal from the switch, only when all light
devices are added to the same Zigbee network can they repeat the received signal. There are 3 different
situations as follows:
1. If you have a gateway controller and light devices, please add all light devices to the gateway first, then pair
the GP switch to all light devices one by one.
2. If you have only light devices and battery/AC powered Zigbee remote, please set up a Zigbee network using
the light devices and Zigbee remote, then pair the GP switch to all light devices one by one.
3. If you only have light devices, please use a light device to set up a Zigbee network first, then add other light
devices to the network (please refer to the light device manual), then pair the GP switch to other light devices
one by one.