Sunricher SR-ZV9100A-A User manual

Z-Wave In-Wall Smart Switch SR-ZV9100A-A
Safety & Warnings
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Quick Start
How to install:
• Step 1: power on the Z-Wave In-wall Smart switch.
• Step 2: activate inclusion mode on your Z-Wave controller.
• Step 3: activate inclusion mode of the switch by triple press the action button on the switch. The switch
will be included to Z-Wave network.
Product Description
The in-wall smart switch is a Z-Wave device designed to work with various types of light sources. It may be
connected to two-wire or three-wire configuration so it can operate with or without neutral lead. The switch
can switch ON/OFF connected light source either through Z-Wave devices or through the wall switch
connected directly to it.
The switch can be included and operated in any Z-Wave network with other Z-Wave certified devices from
other manufacturers and/or other applications. All non-battery operated nodes within the network will act
as repeaters regardless of vendor to increase reliability of the network.
The encryption mode that the switch supports is S2 Unauthenticated. When the switch is being included
into a Z-Wave network, you can use your primary controller/gateway to enable encryption mode or disable
encryption. (The primary controller/gateway shall support encryption mode configuration). The switch
supports OTA and can update firmware wirelessly.
Action button
AC power input
Load output
Reset
LL NN
OUT AC 100-240V
Switch input
Function Introduction
S1
COM
(2-wire with No Neutral input)
(3-wire with Neutral input)
(2-wire with No Neutral output)
(3-wire with Neutral output)
In-wall Smart
Switch
SR-ZV9100A-A(868.42MHz)
Ratings:230V~,50Hz,MAX:4.8A ( )
Made in China
MAX:2.4A ( )
1

Main Features:
• Compatible with any Z-Wave or Z-Wave+ Controller,
• Controlled by Sunricher EasyHome or any other Z-Wave controller,
• Soft start function,
• Works with various types of switches – momentary, toggle, three-way, etc.
• Active element: semiconductor electronic switch,
• To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of
applicable regulations,
• The Bypass is an extension unit.
The switch operates under the following loads:
• Conventional incandescent and HV halogen light sources
• ELV halogen lamps (with electronic transformers)
• MLV halogen lamps (with ferromagnetic transformers)
• Compact fluorescent CFL tube lamps with electronic ballast
• Fluorescent tube lamps with electronic ballast
• Supported light sources (power factor > 0.5) with minimal power of 5VA using the Bypass (depending on
the type of load)
Z-Wave Frequency
Input Voltage
Output Voltage
Output Current
Operating temperature
Relative humidity
Dimensions
868.42 MHz (EU)
AC100-240V
AC100-240V
Resistive load: max. 4.8A
Capacitive/Inductive load: max. 2.4A
0 to 40°C
8% to 80%
45.5x45x20.3mm
Product Data
Installation Guide
Please read carefully the enclosed user manual before installation of the in-wall switch, in order to ensure
an error-free functioning.
ATTENTION: Prior to the assembly of the product, the voltage network has to be switched OFF and
ensured against re-switching.
Inclusion (adding to a Z-Wave network)
1. Set primary controller/gateway into inclusion mode (Please refer to your primary controller’s manual on
how to turn your controller into inclusion).
2. Power on the in-wall switch and set it into inclusion mode. There are two methods to set the in-wall
switch into inclusion mode:
2

1)Repower on the switch, it will be set into inclusion mode automatically, and waiting to be included.
2)Triple press the action button on the switch, it will set the switch into inclusion mode.
Exclusion (removing from a Z-Wave network)
There are two exclusion methods:
Method 1: Exclusion from the primary controller/gateway as follows:
1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers
manual on how to set your controller into exclusion).
2. Triple press the action button, the switch will be set to exclusion mode, and waiting to be excluded, then
the switch will be excluded from the network.
Method 2: Factory reset the switch will force it to be excluded from a network. (please refer to the part
“Factory Reset” of this manual)
Note: Factory reset is not recommended for exclusion, please use this procedure only if the primary
controller/gateway is missing or otherwise inoperable.
Factory Reset
Press and hold down the action button for over 10 seconds, the switch will be reset to factory defaults.
Association
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another
device is called association. In order to control a different device, the controlling device needs to maintain
a list of devices that will receive controlling commands. These lists are called association groups and they
are always related to certain events (e.g. button pressed). In case the event happens all devices stored in
the respective association group will receive a common wireless command.
Association Groups:
Association
Groups Description
1. When press and hold down “Reset” button for 10S to reset
the switch, send "Device Reset Locally Notification CC" to
associated devices of this group to report factory reset
information.
2. When load state changes, send "Basic Report CC" to
associated devices of this group.
3. When over temperature is detected, send “Emergency
shutoff status" to Lifeline.
Group 1
Group
Name
Lifeline
Max
Nodes
5
Set and unset associations:
(Note: All association information will be cleared automatically once the switch is excluded from a
network.)
Set association by operating primary controller/gateway to send packets to the switch:
3

The primary controller/gateway sends packets to the switch using “Command Class ASSOCIATION”
Operating the device
Short press the action button on the switch to switch ON/OFF the load.
Node Information Frame
The Node Information Frame is the business card of a Z-Wave device. It contains information about the
device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by
sending out a Node Information Frame. Beside this it may be needed for certain network operations to
send out a Node Information Frame.
How to send out Node Information Frame:
When the switch is set to inclusion/exclusion mode again, it will send out Node Information Frame, there
are 2 kinds of operation as follows:
1. triple press the action button, the switch will be set to inclusion/exclusion mode, then send out Node
Information Frame.
2. When the switch is under inclusion mode, there are two kinds of operation:
1) Triple press inclusion/exclusion button, the switch will be set to inclusion mode again, and send out
Node Information Frame.
2) Power off and power on the switch, it will be set to inclusion mode automatically, and send out Node
Information Frame.
Technical Data
SUPPORTED COMMAND CLASS
Wireless Range
SDK
Explorer Frame Support
Device Type
Generic Device Class
Specific Device Class
Role Type
Routing
up to 100 m outside, on average up to 40 m inside buildings
6.71.03
Yes
on/off Power Switch
GENERIC_TYPE_SWITCH_BINARY
SPECIFIC_TYPE_POWER_SWITCH_BINARY
Always On Slave (AOS)
Yes
Node Info Security Command Supported Report
COMMAND_CLASS_ZWAVEPLUS_INFO COMMAND_CLASS_MANUFACTURER_S
PECIFIC
V2 V2
4

COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SUPERVISION
V1
V1
V1
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_SCENE_ACTIVATION
OMMAND_CLASS_SCENE_ACTUATOR_C
ONF
COMMAND_CLASS_NOTIFICATION
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_ASSOCIATION_GRP
_INFO
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_FIRMWARE_UPDATE_
MD
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_DEVICE_RESET_LOC
ALLY
V1
V1
V1
V8
V1
V3
V2
V4
V1
V1
Notification Command Class
The switch supports Emergency shutoff, when inside temperature is over 90℃ and
detected by the built-in thermistance, the switch will send out Emergency shutoff status
to Lifeline.
Notification Type
System (0x09)
Notification
Emergency shutoff status (0x07)
Configuration Command Class
Size Description Default Value
Parameter
Info: Saving load state before power failure
0 － shutoff load
1 － turn on load
2 － save load state before power failure
2 1 2
COMMAND_CLASS_TRANSPORT_SERVICE COMMAND_CLASS_VERSION
V2 V2
5

Added to and removed from a network through
external switch (when enables this function,
triple press the external switch within 1.5
seconds to be added to or removed from a
network)
0 - disable
1 - enable
41 1
External switch type
0 – Push button switch
1 – normal on/off switch
2 – 3-way switch
51 0
Info: Enable/disable to send the basic report to
the Lifeline when the load state changed
0 － Disable to send Basic report
1 － Enable to send Basic report
31 1
Wiring Diagram
Notes for the diagrams:
L - terminal for live lead
N - terminal for neutral lead
Out - output terminal of the switch (controlling connected light source)
S1 - terminal for switch (has the option of entering the device in inclusion/exclusion mode)
COM - terminal for grounding to the switch connected to the switch
Compatible Load Types
Supported load types 100-240V~
Resistive loads
Conventional incandescent and halogen light
sources
Capacitive loads
Fluorescent tube lamp (compact / with
electronic ballast), electronic transformer, LED
Inductive loads
Ferromagnetic transformers
Max. 4.8A
Max. 2.4A
Max. 2.4A
6

(1) 2-Wire Connection With No Neutral Lead
The Bypass is a device designed to work with the in-wall smart switch. It should be used in case of
connecting LED bulbs or energy saving compact fluorescent lamps. The Bypass prevents flickering of the
LED lights and glowing of the turned off compact fluorescent lamps. In the case of 2-wire connection, the
Bypass allows to reduce minimum power of load required by the switch for correct operation. The Bypass
provides powering of the switch in case of controlling the low loads of minimum power down to 5VA (for
cosφ>0.5).
PUSH
Live
Neutral
Bypass
NOTE: Switch connected to the S1 terminal
activates the basic functionality of the switch
(turning the light on/off) and starts the
inclusion/exclusion mode (Add/Remove).
(2) 3-Wire Connection With Neutral Lead
PUSH
Live
Neutral
NOTE: Switch connected to the S1 terminal
activates the basic functionality of the switch
(turning the light on/off) and starts the
inclusion/exclusion mode (Add/Remove).
Reset
LL NN
OUT AC 100-240V
S1
COM
In-wall Smart
Switch
SR-ZV9100A-A(868.42MHz)
Ratings:230V~,50Hz,MAX:4.8A ( )
Made in China
MAX:2.4A ( )
Reset
LL NN
OUT AC 100-240V
S1
COM
In-wall Smart
Switch
SR-ZV9100A-A(868.42MHz)
Ratings:230V~,50Hz,MAX:4.8A ( )
Made in China
MAX:2.4A ( )
7

(3) 3-Way Switch Connection
(4) Momentary Wall Switch Connection
3-Way Switch (SPDT)
3-Way Switch (SPDT)
Reset
LL NN
OUT AC 100-240V
S1
COM
In-wall Smart
Switch
SR-ZV9100A-A(868.42MHz)
Ratings:230V~,50Hz,MAX:4.8A ( )
Made in China
MAX:2.4A ( )
Reset
LL NN
OUT AC 100-240V
S1
COM
In-wall Smart
Switch
SR-ZV9100A-A(868.42MHz)
Ratings:230V~,50Hz,MAX:4.8A ( )
Made in China
MAX:2.4A ( )
8