Swegon ADAPT Parasol EXb Series Guide

ADAPT Parasol EXb
Installation – Commissioning – Maintenance 20191101
Art. 942428024
A1, B1
B2A2
Installation

ADAPT Parasol EX
2Swegon reserves the right to alter specications. 20191101
A3
A4
A5
B3
B4
A6, B5
M8

3
20191101 Swegon reserves the right to alter specications.
ADAPT Parasol EX
utvändig gänga DN (1/2”)
A7, B6

d/2
A8, B7
Water
Control equipment
 Note that clamp ring couplings require support sleeves inside the pipes.
DN15 (1/2”) male threads

ADAPT Parasol EX
4Swegon reserves the right to alter specications. 20191101
A9, B8
A10, B9
A9, B8
B C F G H I
RoHS
C F G H I
RoHS
B
grey
black
green
blue
red
24V
G0
24V
G0
G0
Sensor
Condens
24V
24V
blue (US=black)
brown (US=white)
brown
white
brown (US=white)
|1 2 |3 4 |5 6 |7 8 |9 10 11 12 |
|13 14 15 |16 17 18 |19 20 21 |
| 22 | 23 | 24 | 25 |
black
brown
blue
black
white
G
Condens
brown
white
yellow
A B C D E F G H I
RoHS
VOC CO2
Sensor
RoHS
1. 2.
0-10V DC
0-10V DC
blue (US=black)
G0
G0
Wiring
1. Wiring when not using VOC sensor
2. Wiring when using VOC sensor

5
20191101 Swegon reserves the right to alter specications.
ADAPT Parasol EX
RS 485 type Belden 9842
20
Master
21
Slave
22
Slave
23
Modbus
1 2 3 4 5 6 7 8910 11 12 13 14 15 16
Modular 6/6 RJ12
Modular 6/6 RJ12
22 23 24 25
Modular
6/6 RJ12
| 1 2 | 3 4 | 5 6 | 7 8 | 9 10 11 12 |
|13 14 15 |16 17 18 | 19 20 21 |
| 22 | 23 | 24 | 25 |
| 1 2 | 3 4 | 5 6 | 7 8 | 9 10 11 12 |
|13 14 15 |16 17 18 | 19 20 21 |
| 22 | 23 | 24 | 25 |
MB id 8
Master
MB id 4
Master
22 23 24 25
MB id 5
Slave, extract air
Modular
8/8 RJ45
G0 24V AC
G
Modular
6/6 RJ12
1 2 3 4
MB2
5 6 7 8
MB1
Next Zone
CONTROL Zone
MB id 1
Super WISE
1 2 3 1 2 3
-
+
C
Zone
Room
| 1 2 | 3 4 | 5 6 | 7 8 | 9 10 11 12 |
|13 14 15 |16 17 18 | 19 20 21 |
| 22 | 23 | 24 | 25 |
MB id 4
Master
20
Master
21
Slave
22
Slave
23
Modbus
1 2 3 4 5 6 7 8910 11 12 13 14 15 16
22 23 24 25
Modular 6/6 RJ12
Modular 6/6 RJ12
22 23 24 25
Modular
6/6 RJ12
| 1 2 | 3 4 | 5 6 | 7 8 | 9 10 11 12 |
|13 14 15 |16 17 18 | 19 20 21 |
| 22 | 23 | 24 | 25 |
| 1 2 | 3 4 | 5 6 | 7 8 | 9 10 11 12 |
|13 14 15 |16 17 18 | 19 20 21 |
| 22 | 23 | 24 | 25 |
MB id 1
Slave id 1
MB id 4
Master
22 23 24 25
20
Master
21
Slave
22
Slave
23
Modbus
1 2 3 4 5 6 7 8910 11 12 13 14 15 16
Room
Room
CONNECT Adapt
CONNECT Adapt
CONNECT Adapt
RK 2x0,75
Modular
6/6 RJ12
20
19
Room with ADAPT Damper extract air
Next room with Connect Adapt
Room with ADAPT Parasol only (Master / Master)
Room with ADAPT Parasol only (Master / Slave)
ADAPT Damper settings
• Slave MB id (5,6,7,9,10,11 etc. if Super WISE system)
• Slave function (Application type =3)
• Extract Air (Tempsensor use =1)
• Operation = normal (commissioning mode when delivered)

ADAPT Parasol EX
6Swegon reserves the right to alter specications. 20191101
A11, B10
A12 , B11
TORX T-25 / 1 x 8
A13, B12
ON
1 2
Click!
A14, B13
ON
1 2

7
20191101 Swegon reserves the right to alter specications.
ADAPT Parasol EX
A15, B14
A16 B15
A17, B16

ADAPT Parasol EX
8Swegon reserves the right to alter specications. 20191101
A18, B17
A19, B18

9
20191101 Swegon reserves the right to alter specications.
ADAPT Parasol EX
q = k · √p [l/s]
i
p = [Pa]
i()
k
q2
[pi Pa]
q [l/s]
k= k-factor
1
2
4
3
ADAPT Parasol EX Nozzle setting
per side
Side k-factor
690 L1&3 0,253
690 L2&4 0,253
690 M1&3 0,44
690 M2&4 0,44
690 H1&3 0,693
690 H2&4 0,693
1290 L1&3 0,253
1290 L2&4 0,665
1290 M1&3 0,44
1290 M2&4 1,16
1290 H1&3 0,693
1290 H2&4 1,825
Nozzle configuration
H M L
H =
M=
L=
1 x 8
T-25
Pi(2,4)
Pi(1,3)
Commissioning
1k (1+3) + pi(1,3) => q (1+3)
The K-factor of the short sides together with the
commissioning pressure reading of these equals
the flow of the short sides, 1&3.
2k (2+4) + pi(2,4) => q (2+4)
The K-factor of the long sides together with the
commissioning pressure reading of these equals
the flow of the long sides, 2 & 4.
3q tot =q (1+3) + q (2+4)
The product's total flow is the sum of the above.
NB! pi(1,3) = pi(2,4)
NOTE: The commissioning pressure is diffe-
rent for the long sides (2 & 4) and the short
sides (1 & 3).
/

ADAPT Parasol EX
10 Swegon reserves the right to alter specications. 20191101
X-shape
Fan-shape
Commissioning/Checking the airflows
Constant pressure in the zone with the CONTROL Zone
damper or similar damper.
• Check that all the WISE products are energized.
• Make sure that all the ADAPT Parasol EX modules have
their correct K-factors.
• Make sure that all the modules are set to the max. flow
commissioning mode. (On delivery, the product is set to
this mode, 3 blue LEDs + 3 red LEDs are lit).
• Connect up to the control unit on the ADAPT Parasol EX
(see separate SWICCT instructions) and carry out a per-
formance check.
• Test the operating modes, the min./max. flows, open/
close the actuators. If the ADAPT Parasol EX has been
configured at the factory, check that the settings agree
with the project design data. If the module is an ADAPT
Parasol EX stock (stocked product), it must be program-
med according to the data for which the product has
been calculated. Make also sure that the Modbus addres-
ses agree if SuperWISE or some other BMS system will be
used.
• If SuperWISE will be used, make sure that all products are
in the SuperWISE tree structure. If all the products are
not in the tree structure, look over the Modbus addresses
via SWICCT and check cables and connections. (See the
separate instructions for the SuperWISE).
• Make sure that the pressure sensor and sensor module
have the correct Modbus address. The Master must have
a 0 setting on the pressure sensor and sensor module. Set
the Slaves, if required, in number sequence: 1, 2, 3, 4, 5,
6, 7, 8, 9
• Before you begin commissioning, make sure that the air
handling unit is started up and the fire damper, if re-
quired, is fully open and that the zone damper is in full
operation.
• Check the flow compared to the max. flow in the zone,
adjust the pressure set point until the correct flow is ob-
tained with TUNE Control. If Max. flow is not achieved, it
will be necessary to close another/other zone damper(s).
• The reference product can be found, i.e. the one with the
greatest deviation from the design max. flow, by measur-
ing the max. flow of all the ADAPT Parasol EX modules in
the zone.
• Measure and record the airflow with the damper set to
the max. position on the reference ADAPT Parasol EX
in the zone. Reset the module to the min. flow setting,
measure and record the airflow.
• Set the module back to the max. flow setting.
• Carry out the same procedure for all the ADAPT Parasol
EX modules in the zone.
• Decrease the pressure set point on the zone damper if
pressure is needed for other zones, for example: 5 Pa.
• Commission the remaining zones following the same
procedure.
• Check/ adjust the previous shut off zones in the same
way.
• Reset the pressure set points on all the zone dampers.
• Identifiy the reference zone, i.e. the zone with the lowest
flow compared with the design max. flow (for example
by checking relevant flow across each zone damper using
the TUNE Control hand-held terminal).
• Set the min. flow on a number of ADAPT Parasol EX mo-
dules or use the zone damper for setting the min. flow so
that the ventilation system responds to the simultaneous
load.
• Adjust the pressure set point of the air handling unit
until the zone damper of the reference zone is 85 – 90%
open. (Managed by the SuperWISE if one is used).
• Reset all the settings and set all the ADAPT Parasol EX to
the normal operation setting.
• Check and measure the max. flow and min. flow with the
SWICCT or the SuperWISE.

11
20191101 Swegon reserves the right to alter specications.
ADAPT Parasol EX
To reach the menu, hold the left-hand and right-hand
buttons down for five seconds.
With the left-hand button ( ) you advance through the
menus. With the right-hand button ( ) you confirm your
selection.
Press the left-hand but-
ton and select:
1. Alarm list
2. Commissioning air
3. Commissioning water
6. Return to menu
Press the right-
hand button to
confirm your
selection
The alarm is displayed by a number of diodes when you
have selected Alarm list (1) in the menu.
Each diode represents a number as shown in the table
above and the numbers should be added up to form an
alarm number.
Ex. The centremost blue and the two last red diodes are
lit (xoxxoo)
The centremost blue one corresponds to 16, the penulti-
mate red one to 2 and the last red one to 1. The sum of
these is 19, which is the alarm number.
Return to normal operation by pressing the right-hand
button.
Alarm list for the sensor module
Alarm no. Type of alarm 32 16 8421
Alarm 1 Supply voltage low
Alarm 2 Supply voltage critically low
Alarm 3 Ext temp missing
Alarm 4 Ext temp error
Alarm 5 Condensation sensor error
Alarm 6 SM temp sensor error
Alarm 7 SM button error
Alarm 8 CO
2
sensor missing
Alarm 9 VOC Error
Alarm 10 Low pressure
Alarm 17 SM comm error
Alarm 18 Slave comm error
Alarm 19 Pressure sensor comm error
Alarm 20 VOC sensor comm error
Alarm 21 No master request (slave)
Alarm 22 Slave incompatible version
Alarm 25 Heating comfort alarm
Alarm 26 Cooling comfort alarm
Alarm 27 Temp. Set point overlap alarm
Alarm 28 Air quality comfort alarm
Alarm 29 Condensation
Alarm 33 24 V Out 1 overload error
Alarm 34 24 V Out 2 overload error
Alarm 35 24 V Out 3 overload error
Alarm 41 Slave input common alarm
Alarm 42 Slave output common alarm
ON
1 2
Presence detector
Diodes for temperature,
commissioning or alarm
indication
Function button
Diode-indicating function
- Green = Ok
- Flashing Green = Condensation alarm
- Yellow = Alarm
- Green/Yellow=Comfort alarm
(not acute)
Temperature sensor
3 parallel RJ12 ports
(Modbus) for connecting a
controller, another sensor module or
a computer, for example, by means
of a Cable converter USB-RJ12
Function button
Switch/Termination resistance. Switch 1 should be
”on” for the last sensormodule in the loop.
Dial for addressing the appropriate sensor module if
several are used in the same loop.
10 senormodules can be connected to the same master,
and each and one of them need an unique address.
1. Alarm list: See the complete alarm list to the right.
In the commissioning menus:
• Navigate between the menus by pressing the left-hand
button
• Confirm selections by pressing the right-hand button
• When a selection has been confirmed, the blue LED will
flash for about 60 seconds.
• In order to return to normal operation, select "no adjust-
ment"
2. Commissioning, Air:
2.1. Min. airflow, no occupants
2.2. Min. airflow, occupancy
2.3. Max. airflow, occupancy
2.4. Min. airflow, holiday/longer period
of no occupancy
2.5. No adjustment
3. Commissioning, Water:
3.1. Open the chilled water valve
3.2. Open heated water valve
3.3. No adjustment
4, 5 are not used
6. Return to menu
Menu:

ADAPT Parasol EX
12 Swegon reserves the right to alter specications. 20191101
ON
1 2
ON
1 2
2
1
3
5
6
7
8
4
9
Maintenance