Symmons Naru 412HS Manual

Naru®
Model Numbers Specification
Warranty
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Accessory Suite
Operation & Maintenance Manual
412HS, 412SH, 412W
Note: Append appropriate -sufx to model number.
Modifications
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-PNL Polished Nickel finish
-STN Satin Nickel finish
412HS Hand Shower Assembly
412SH 3 Mode Showerhead
412W 3 Mode Hand Shower Wand
Hand shower assembly includes dual checks for back ow
protection, 3 mode showerhead and 3 mode hand shower
wand with standard 2.5 gpm (9.5 L/min) ow restrictor.
Components are made from metal and nonmetallic
materials plated in standard polished chrome nish.
-ASME A112.18.1/CSA B125.1
-WaterSense 1.5, 2.0 gpm (412SH only)
Compliance
Certied by
CSA Group
CG

2
Dimensions
Measurements
A
Female 1/2" IPS thread
must be recessed
7/8", 22 mm
from nished wall
B 3-1/4", 83 mm
C Ø 2-1/4", 57 mm
D Ø 1-1/2", 38 mm
E 3-3/4", 95 mm
F11/16" ± 1/8"
17 mm ± 3 mm
G 5", 127 mm
H 3-5/8", 92 mm
I 8-1/4", 210 mm
Note: Dimensions subject to change without notice.
BB
E
E
GG
D
D
C
C
A
A
H
H
412SH
412W
412HS
II
FF

3
Parts Breakdown
Replacement Parts
Item Description Part Number
A
B
Wall Elbow
Wall Elbow Flange T-444-KIT
C 60" Hose EF-02976
D
E
F
G
H
I
Cradle Mount
Cradle Mounting Screws
Anchors
Washer
Cradle Arm
Set Screw
T-545
J Hand Shower 412W
K Showerhead 412SH
Notes:
1) Append -PNL to part number for polished nickel
nish; -STN for satin nickel.
2) Append -1.5 or -2.0 to showerhead or hand shower
for low ow.
Required for Installation
Adjustable wrench
Phillips head screwdriver
Plumber tape
B
412HS
412SH 412W
K
A
J
E
D
H
I
G
F
C

4
Installation
1) Install wall elbow (A) and
ange (B) to recessed pipe
tting. Turn elbow clockwise to
tighten (412HS only).
3b) Option: Place mounting
plate (D2) in position. Mark and
drill 1/4" (6 mm) holes into wall.
Install anchors.
5) Attach cradle arm (H) and
washer (G) to cradle mount (D).
Secure with set screw (I).
2) Press tab to remove mounting
plate (D2) from cradle mount
cover (D1).
3a) Place mounting plate (D2) in
position. Mark and drill 1/8" (3 mm)
pilot holes into stud.
Note: Mounting plate (D2) center
tabs must be horizontal for removal.
4) Install mounting plate (D2).
Secure with two screws (E).
Replace cradle mount cover (D1).
1
2
A
B
1
D2
2
2
1
D1
D2
1
3
2
D2
1
3
2
E
D2
D2
D1
1
2
D
I
G
H
Note: Mounting plate (D2) center
tabs must be horizontal for
installation.

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2018 Symmons Industries, Inc. ■symmons.com ■[email protected] ■ZV-3081 REV A ■040918
Installation Cont.
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then quickly
rinse with water.
Troubleshooting Chart
1
2
J
3
1
4
2
C
K
A
C
6) Install showerhead (J) to shower
arm turning clockwise to tighten
(412SH only).
7) Attach large end of hand
shower hose (C) to hand shower
wand (K). Attach small end
of hand shower hose (C) and
washer to wall elbow (A). Turn
clockwise to tighten.
Notes:
1) DO NOT use plumber tape on
ttings with face seal washers or
o-ring seals.
2)
DO NOT OVERTIGHTEN ttings
with face seal washers or o-ring
seals.