Symmons Oxford 4200-TRM Manual

1
4200-TRM, 4201-TRM, 4202-TRM
Oxford®Tub/Hand Shower Trim Series
Operation & Maintenance Manual
Model Numbers Specifications
4200-TRM Valve Trim
4201-TRM Shower Trim
4202-TRM Tub/Shower Trim
Tub/shower trim with lever handle includes diverter
tub spout and 1 mode showerhead with standard
2.5 gpm (p.5 L/min) ow restrictor. Shower trim with lever
handle includes all of the above less diverter tub spout.
Valve trim with lever handle includes shower escutcheon
only. Components made from metal and nonmetallic
materials plated in standard polished chrome nish.
Modifications Compliance
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-ORB Oil rubbed bronze finish
-STN Satin nickel finish
-ASME A112.18.1; CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Note: Append appropriate -sufx to model number.
c
WARNING: This product can expose you to chemicals
including lead, which is known to the state of California
to cause cancer, birth defects, or other reproductive
harm. For more information, go to
www.P65Warnings.ca.gov.

2
Dimensions
Measurements
A 6 1/2", 165 mm
B 9 5/8", 245 mm
C 77", 1956
D 7 1/2", 191 mm
E 3 1/2", 89 mm
F
32", 813 mm (4202-TRM)
42", 1067 mm (4200-TRM,
4201-TRM)
G 12", 305 mm
H 2 9/16", 65 mm
I 4", 102 mm
J 1/2" NPT
K 4", 102 mm
L(Rough in)
2" ± 1/4", 51 mm ± 6 mm
M 2 1/2", 64 mm
N 6 1/2", 165 mm
Notes:
1) All dimensions measured from nominal rough-in (see L as reference).
2) Dimensions are subject to change without notice.
DD
M
M
F
F
G
G
C
C
B
B
H
H
I
I
A
A
L
L
N
N
K
K
J
J
FloorFloor
E
E

3
Parts Breakdown
Replacement Parts
Item Description Part Number
A Shower Arm 422SA
B Showerhead 422SH
C
F
G
Handle
Set Screw
Flange
T-549
D
H
Locking Ring
Dome Cover T-543
L Tub Spout 422TSD
E
I
J
K
Gasket
Shower Escutcheon
Mounting Screws
Mounting Plate
T-542-NS-K001
Notes:
1) Append -ORB to part number for oil rubbed bronze
nish; -STN for satin nickel.
2) Append -1.5 or -2.0 to showerhead for low ow.
Required for Installation
Adjustable wrench
Phillips head screwdriver
Allen wrench (1/8")
Plumber tape
I
JK
B
H
D
E
C
F
G
A
L

4
Installation
Note:
For valve body installation, please
see valve body installation guide.
1) Install mounting plate (K) to
shower valve (4000-BODY).
Secure with two screws (J).
2) Attach gasket (E) to back of
shower escutcheon (I). Attach
shower escutcheon (I) to
mounting plate (K).
Note: Tabs should snap into place.
3) Install dome cover (H). Secure
with lock ring (D).
4) Install handle (C) and
ange (G) to valve. Secure handle
by tightening set screw (F).
Note: Handle should be facing the
6 o'clock position.
5) Install tub spout (L) to pipe tting.
Turn clockwise to secure.
6) Attach shower arm (A) to vertical
shower pipe turning clockwise to
tighten.
7) Install showerhead (B) to shower
arm (A) turning clockwise to
tighten.
1
2
H
D
K
IE
1
2
C
G
F
1
2
L
1
2
B
A
1
2
A
1
2
J
K

5
Care and Cleaning
1) Clean nished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse
with water.
Troubleshooting Chart
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then
quickly rinse with water.
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
Copyright © 2018 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3052 REV A 080118
1) Turn shower handle counterclockwise approximately
1/4 turn to put valve in cold position.
2) Turn shower handle counterclockwise approximately
1/2 turn to put valve in warm position.
3) Turn shower handle counterclockwise approximately
3/4 turn to put valve in hot position.
Operation
Temperature Control