Symmons Allura SLW-4712 Quick guide

Non-
Removable Removable
Stopper Stopper
Quick Install Guide Allura Widespread Lavatory Faucet, SLW-4712
Step 1
Attach control valves to sink
Step 1
Attach center spout to sink
Step 2
Attach pivot rod to drain body
Step 6
Connect lift rod, clevis strap,
pivot rod and adjust linkage
Step 7
Install stopper and
set eye position
Step 5
Flush water supply lines
Step 9
Attach drain body to drain trap
Step 8
Step 3
SConnect water supply lines
Fasten drain body and
tail piece to sink
Step 4
Tools & Materials Need Help?
Contact Symmons customer service at
[phone], [phone]
Email: [email protected]
Monday - Friday 7:30 am - 7:00 pm EST
Please check Symmons website
for technical help, the latest product
information and warranty policy.
www.symmons.com/service
Widespread Lavatory Faucet SLW-4712
Installation and Service Instructions
Allura®
Model Numbers
SLW-4712 Lavatory faucet with
pop-up drain
Note: Instructions replace document
ZV-782 as of June 2012.
Alternate Finish Code
append to part numbers when applicable
-STN Satin Nickel
-- Chrome (standard)
Compliance
- ASME A112.18.1/CSA B125.1
- NSF/ANSI 61.9, NSF/ANSI 372
- WaterSense 1.0 & 1.5 gpm
Certied by
NSF International
Plumbers
Putty
Pipe
Sealant
5/64"

Step 3 Connect water supply lines
■read tee onto
end of spout.
Note: is may
require 4inches
of clearance.
■Apply pipe
sealant on both
ex hose adapters.
read into side
of tee.
■Attach ex hoses
to ex hose
adapters.
■Plumb hot
water supply to
le valve body
inlet, cold water
to right inlet
(1/2 inch supply hoses not included).
■Check for leaks if only replacing faucet and drain is already
installed by rst turning faucet handles to the OFF position
and then turn water supply valves ON.
Step 4 Fasten drain body to sink
■Remove stopper, unscrew ange and remove at rubber
washer from end
of drain body as shipped.
■Apply plumber’s putty
around bottom of ange.
■Move friction washer,
beveled washer and
ange nut down away
from end of drain body.
■Place ange into drain
opening and from under
sink screw drain body
into ange at least 2-3
turns until hand tight.
Apply putty or teon tape
to tail piece and attach to
drain body.
■Position drain body so
pivot cavity is facing rear of
sink and then slide beveled
washer and friction washer
up against sink.
■Tighten ange nut up
against friction washer to
evenly compress beveled washer while also ensuring ange is
centered in drain opening.
Take care not to over tighten ange nut.
Caution: If replacing an older faucet ensure water supply is
turned OFF before removing. en turn both faucet handles to
the ON position to relieve water pressure.
Step 1 Attach control valves to sink
■read ange nut
down about 2inches
from threaded end
of valve body.
■Insert valve body
from underneath
sink up through
mounting hole.
Ensure valve with
red striped hose (hot)
is on the le and blue
(cold) is on the right.
■Place gasket over valve
body and thread
fastener onto valve
body until fastener
is secured tightly to
valve body.
■Ensure spindle
is rotated to the
OFF position.
Fasten handle to top
of spindle located
in OFF position as
shown in illustration.
■Press plug button into
top of handle.
■Tighten ange nut
and mounting washer
under sink and secure with mounting screws if necessary.
Step 2 Attach center spout to sink
■Unscrew tee and
remove washer and
nut from threaded
end of spout as
typically shipped.
■Insert through
mounting hole
in sink and then
fasten from under
sink with washer
and nut.
■Tighten nut while
ensuring spout
is centered over
mounting hole and
at edge of washer is
facing rear of sink.
Installation Instructions
fastener
gasket
valve body
mounting washer
ange nut
mounting screws
hot = cw
cold = ccw
spindle OFF
plug button
screw
handle
spout
washer
nut
tee
Pipe
Sealant
ex hose
spout
valve
outlet
&inlet
ex hose
adapter
tee
valve
body
PLUMBERS
PUTTY
ange
beveled
washer
friction
washer
pivot
cavity
ange nut
drain body
tail piece
Installation Instructions
Page 2

Step 5 Install stopper and set eye position
Stopper can be removable
or non-removable
determined by position
of eye hole when
inserting pivot rod.
■Insert stopper
through ange
opening and rotate to
position eye hole.
Removable stopper
When installed in removable position, move pivot rod to
the up position (li rod is in the down position when later
installed). Eye hole will slide over end of pivot rod.
Step 6 Attach pivot rod to drain body
■Remove retaining nut and outer seat from pivot cavity.
■Insert pivot rod into
pivot cavity so pivot
ball is against inner
seat and rod passes
under end of stopper
according to selected
eye hole position.
■Insert outer seat
over pivot rod with
curved end against
pivot ball.
■Fasten pivot rod to drain body with retaining nut
and tighten using your ngers until ball is seated
snug and pivot rod can move around freely.
Step 7 Connect lift rod and adjust linkage
■Insert li rod through hole on top of water spout.
■Fasten end of pivot
rod with spring clip
through location hole
in clevis strap that is
best aligned to enable
li rod also fasten to
end of clevis strap when
in the up position and
stopper is in the closed
position.
■Insert li rod into
end of clevis strap
and fasten with
thumb screw at location
where stopper can be
easily opened and
closed.
If necessary, select
another location hole
in clevis strap and re-adjust li rod where fastened to clevis
strap
Step 8 Flush water supply lines
oroughly ush the supply lines to prevent foreign matter, i.e.
copper chips, sand, etc.
from damaging the
sealing surface inside
control valves.
■Remove aerator from
end of faucet water
outlet by rotating
counter clockwise.
■Turn hot and cold
faucet handles
to full ON position,
open water supply
valves
and run long enough to ush supply lines thoroughly.
■Turn faucet OFF, replace aerator, and check for any water leaks.
Care of faucet finish
Clean nish area by using mild soap and water or non-abrasive
cleaner and then rinse immediately. A non-abrasive wax may
be used to preserve nish area.
Valve cartridge replacement
Remove faucet handle
■Pry loose and remove plug button
using your nger.
■Remove Phillips head screw
in center of handle.
■Li o handle from
cartridge spindle.
Remove cartridge
Using a wrench, turn hex nut
on cartridge counter clockwise.
Note: Ensure valve assembly doesn’t
rotate under sink while turning nut.
Insert new cartridge
Insert replacement cartridge into
center of valve and tighten hex nut
using a wrench.
Attach handle
■Ensure cartridge spindle is
rotated to the OFF position.
■Attach handle located
in the OFF position as
shown in illustration.
■Insert screw into
center of handle
and replace plug button.
stopper
ange
non
removable removable
pivot rod
retaining nut
outer seat
pivot ball
inner seat
pivot cavity
thumb
screw
location
holes
spring
clip
pivot rod
clevis strap
lift rod
remove
aerator
hot = cw
cold = ccw
spindle OFF
cartridge
valve
plug button
screw
handle
handles set in
the OFF position
Page 3

RL-072*plug buttons
screw
handle
KN-114 (hot)
OFF = CW
KN-113 (cold)
OFF = CCW
valve cartridge
KN-113
identified
by groove
Handle kit
Part Number Item
Replacement Parts
LN-15
*
FLR-110-1.5
*
FLR-110-1.0
*
aerator ow rates
2.2 gpm (8.3L/min)
1.5 gpm (5.7L/min)
1.0 gpm (3.8L/min)
lift rod
P-108CL12*
standard aerator
2.2 gpm
faucet handle
reference table
valve cartridge
reference table
stopper
P-100N
pop-up drain
assembly
RL-154LR*
includes lift rod
and stopper
Ordering replacement parts:
Call Symmons customer service at [phone],
[phone], M-F 7:30 am - 7:00 pm EST or
check our website at
www.symmons.com for a
list of Symmons distributors.
Parts Assembly Allura Widespread Lavatory Faucet, SLW-4712
(red stripe on hot hose)
(blue stripe
on cold hose)
aerator
*
Note: When ordering replacements parts for
faucets with an optional decorative nish, append
appropriate three letter nish sufx code to part
numbers marked with an asterisk (*
).
4-1/2"
(114 mm)
6-5/16"
(160 mm)
5/8" dia (16 mm)
Hole size
1-1/8" (29 mm) min
1-1/2" (38 mm) max
5/8" (16 mm)
3-1/4"
(83 mm) 1-5/8" (42 mm)
2-1/2"
(64 mm)
3-1/8" (79 mm)
1" dia. (25 mm)
Hole size
1-1/16" (27 mm) min
1-7/16" (37 mm) max
4" (102 mm)
Flexible hose
Deck thickness
1-3/8" (35 mm) max.
Dimensions Allura Widespread Lavatory Faucet, SLW-4712
2-1/4" dia
(58 mm)
2-5/16" dia
(59 mm)
1/2"-14 NPSM
8" (203 mm)
Note: Dimensions subject to change without notice.
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2018 Symmons Industries, Inc. ■symmons.com ■[email protected] ■ ZV-1084 REV F ■071318
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth
defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.