Symmons Degas SLW-5412 Quick guide

Step 4
Connect hoses between
valves and spout
Non-
Removable Removable
position position
Step 5
Attach drain body to ange
Pipe
Sealant
Step 6
Install stopper and pivot rod
Step 7
Connect lift rod,
clevis strap, pivot rod
and adjust linkage
Step 8
Connect supply lines
(supply hoses not included)
HOT
COLD
Step 9
Flush lines and
check for leaks
Step 1
Attach control valves
Step 2
Attach handles
Step 3
Install lift rod & attach spout
Quick Install Guide Degas Widespread Lavatory Faucet, SLW-5412
Thread Locker
Included
Plumbers
Putty
 Need Help?
Contact Symmons customer service at
P: [phone], F: [phone]
Email: [email protected]
Monday - Friday 7:30 am - 6:00 pm EST
Please check Symmons website
for technical help, the latest product
information and warranty policy.
www.symmons.com/service
Tools & Materials
Installation and Service Instructions
Degas®
Widespread Lavatory Faucet SLW-5412
Decorative Finish Code
Append to part numbers when applicable
-STN Satin Nickel
-ORB Oil Rubbed Bronze
-- Chrome (standard)
Model Number
SLW-5412...... Lavatory faucet with
pop-up drain
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth
defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Caution:If replacing an older faucet ensure water supply is turned OFF
before removing, then open faucet valves to relieve water pressure.
Step 1 Attach hot & cold control valves
Step 2 Attach handles
Step 3 Install lift rod and attach spout
Step 4 Connect hoses between valves & spout
Step 5 Attach drain body to flange
Tee and hose assembly required
rotational swing clearance at base
of spout is 4 inches (102 mm)
minimum from hitting back wall
nished deck
front view
rotate until
threads stop
nished deck front view
HOT valve: red label
COLD valve: blue label
5
4
3
2
1
HOT
(red label)
COLD
(blue label)
nished deck
front view
CCW=OFF
CW=OFF
OFF
OFF
ange nut
ange
beveled
washer
friction
washer
back
of sink
PLUMBERS
PUTTY
*use included ange
washer only when
plumbers putty is
not available
*ange washer
(optional)
1
2
Thread Locker
1 drop
nished deck
front view
1
2
Installation Instructions
Page 2

Step 6 Install stopper and pivot rod
Step 7 Connect lift rod and adjust linkage
Step 8 Connect supply lines
Care of faucet finish
Clean finish area by using mild soap and water or non-abrasive
cleaner and then rinse immediately. A non-abrasive wax may be
used to preserve finish area.
Valve cartridge replacement
Step 9 Flush water supply lines
CCW=OFF
OFF
CW=OFF
OFF
Replace handles Lead free brass valve cartridges
(reference replacement parts table)
HOT: OFF=CW
0 or 2 grooves
COLD: OFF=CCW
1 or 3 grooves
depending on supplier
17 mm deep
socket wrench
1 2 3
1/2" (13 mm)
Sealant
non
removable removable
1
2
HOT
COLD
supply hoses
not included
Page 3

KN-114E................
KN-113E................
Single handle kit
Replacement Part Kits
Part Number Item
plug button
phillips panhead
(M4x.7x16 mm)
handle
bushing
handle escutcheon
base and gasket
LN-333-KIT.............
FLR-102-1.5-KIT.....
LN-742-KIT.............
Aerator ow rates
2.2 gpm (8.3L/min)
1.5 gpm (5.7L/min)
1.0 gpm (3.8L/min)
WSF-542L-KIT *.....
aerator removal tool
included in all kits,
p/n LN-383
Aerator
1 handle assembly
included; used for
either hot or cold
Valve cartridge, lead free brass
HOT: OFF = CW
0 or 2 grooves
COLD: OFF = CCW
1 or 3 grooves
Lift rod
RL-205 *
lift rod
standard
aerator
1.5 gpm
1/2" coupling
nuts
widespread
tee tting
1/2 "valve body
ange nut
valve
cartridge
Ordering replacement parts:
Call Symmons customer service at [phone],
M-F 7:30 am - 7:30 pm EST or check our website at
www.symmons.com for a list of Symmons distributors.
* Note: When ordering replacements parts for faucets with
an optional decorative nish, append appropriate three letter
nish sufx code to part numbers marked with an asterisk (*).
spout base
and gasket
u-gasket
u-washer
nut
12" ex hose,
1/8"MNPT x 1/2" NPSM
spout assembly
handle assembly
RL-154LR-11
pop-up drain
assembly
Parts Assembly Degas Widespread Lavatory Faucet, SLW-5412
1/2"-14 NPSM
Hole size
1-1/8" (29 mm) min
1-1/4" (32 mm) max
4" (102 mm) min
Flexible hose
2" dia
(51 mm)
8"(203 mm) min
16"(406 mm) max
Deck thickness
1-5/8" (41 mm) max
Note: Dimensions subject to change without notice
2-3/4" (70 mm)
1/8"
(4 mm)
2-1/4" dia
(57 mm)
1" dia
(25 mm)
5/8" dia
(17 mm)
Hole size
1-1/8" (29 mm) min
1-1/4" (32 mm) max
1-1/8"
(29 mm)
7-3/8"
(186 mm) 5-1/8"
(129 mm) 4"
(102 mm)
5/8" (16 mm)
4-1/2"
(115 mm)
Dimensions Degas Widespread Lavatory Faucet, SLW-5412
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184
Phone: [phone] ■Fax: [phone]
Website:
symmons.com ■Email: [email protected]
Copyright © 2018 Symmons Industries, Inc. ■ZV-1020 REV D ■080118