syslogic TFT/HB PU71 16 Series Operator's manual

U s e r d o c u m e n t a t i o n
TFT/HBxxxPU71x16-xxx
TFT/HVxxxPU71x16-xxx
Document Order code: DOC/Protouch-71
Revision
Date
Author
Modification
1.0
28.01.2014
F. Liechti
Initial Release

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 2/27
Contents
1Introduction 5
1.1. General Remarks 5
1.1. Explanation of Symbols 5
1.1.1. Danger warnings 5
1.1.2. Warnings indicate the following: 5
1.1.3. Information pictograms indicate the following: 6
1.2. Copyright note 6
1.3. Contents of this Documentation 6
1.4. Additional Products and Documents 6
1.4.1. Software products 6
1.4.2. Documents 6
1.4.3. Datasheets 6
1.5. Items delivered 7
1.5.1. Built-in version 7
1.5.2. VESA mount version 7
1.6. Installation 7
1.7. Safety Recommendations and Warnings 7
1.7.1. EMC 7
1.7.2. Battery 8
1.7.3. Hot surface 8
1.8. Electro-Static Discharge 8
1.9. Life Cycle Information 8
1.9.1. Transportation and Storage 8
1.9.2. Assembly and Installation 8
1.9.3. Operation 8
1.9.4. Maintenance and Repair 8
1.9.5. Disposal and WEEE 8
1.9.6. Warranty 9
1.9.7. RoHS 9
2Product Description 10
2.1. Introduction 10
2.1.1. Benefits of Syslogic`s Projected capacitive touch panels 10
2.1.2. Intended use of Projected Capacitive Touch Panels 10
2.2. Device Variants 11
2.3. Accessories 11
2.4. Features 12
2.4.1. HBxxxPU7F16-xxx 12
2.4.2. HVxxxPU71x16-xxx 12
3Hardware Description 13
3.1. Overview 13
3.2. Dimensions 13

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 3/27
3.2.1. HBxxxPU71x16-xxx 13
3.2.2. HVxxxPU71x16-xxx 14
3.3. Mounting 15
3.3.1. TFT/HBxxxPU71x16-xxx 15
3.3.2. TFT/HVxxxPU71x16-xxx 17
3.4. Service Cover 18
3.4.1. TFT/HBxxxPU71x16-xxx 18
3.4.2. TFT/HVxxxPU71x16-xxx 18
3.5. Interfaces 19
3.5.1. Power supply 19
3.5.2. System Interfaces 19
3.6. Touch Screen 19
3.6.1. Basic functions of the touch screen 19
3.6.2. Using On Screen Keyboard (OSK) with Windows7 19
3.6.3. Touch screen calibration using Windows 7 touch driver 20
3.7. Cleaning the Projected capacitive touch panel Fehler! Textmarke nicht definiert.
3.7.1. Cleaning the glas front 20
3.7.2. Cleaning the metal housing 20
4Programming Information 21
4.1. Overview 21
4.1. Operating systems 21
5Technical Data 22
5.1. General Electrical Data 22
5.2. EMI / EMC Specification 24
1.1.1. Emission 24
1.1.2. Immunity 25
5.3. Environmental Specification 25
6Product Revision History 26
6.1. Hardware 26
7Manufacturer Information 27
7.1. Contact 27

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 4/27
List of Tables
Tab. 1 Disposal Materials 9
Tab. 2 Projected capacitive touch panel versions 11
Tab. 3 Projected capacitive touch panel accessories 11
Tab. 4 HBxxxPU71x16-xxx dimensions 13
Tab. 5 HVxxxPU71x16-xxx dimensions 14
Tab. 6 TFT/HBxxxPU71x16-xxx Mounting dimensions 15
Tab. 7 HVxxxPU71x16-xxx VESA dimensions 17
Tab. 8 Power supply connector P1 (1x4 pin) 19
Tab. 9 General Absolute Maximum Ratings 22
Tab. 10 General Recommended Operating Conditions 22
Tab. 11 General Electrical Characteristics 23
Tab. 12 Emission requirements 24
Tab. 13 Immunity requirements 25
Tab. 14 Environmental Specification 25
Tab. 15 Hardware Revision State 26
List of Figures
Fig. 1 HBxxxPU71x16-xxx 12
Fig. 2 HVxxxPU7F16-xxx 12
Fig. 3 Required Cut out HVxxxPU7F16-xxx 15
Fig. 4 Screws to hold the mounting Frame 16

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 5/27
1Introduction
1.1. General Remarks
The content and presentation of this document has been carefully checked. No responsibility is accepted for any errors or
omissions in the documentation.
Note that the documentation for the products is constantly revised and improved. The right to change this documentation at any
time without notice is therefore reserved.
Syslogic is grateful for any help referring to errors or for suggestions for improvements.
The following registered trademarks are used:
CompactFlash trademark of SanDisk Corporation
Intel Atom trademark of Intel Corporation
Windows Embedded Compact trademark of Microsoft Corporation
Windows Embedded Standard trademark of Microsoft Corporation
All other trademarks appearing in this document are the property of their respective company.
1.1. Explanation of Symbols
1.1.1. Danger warnings
The following information is for your personal safety and the prevention of damage to the product described or connected
devices.
Safety instructions and warnings for the prevention of danger to the life and health of users or service personnel and for the
prevention of damage are highlighted in this document by the pictograms specified below. “Warning” and “Information”
pictograms are shown in this document.
1.1.2. Warnings indicate the following:
Death, serious injury or substantial material damage may occur if the related safety measures are not implemented.
The individual “Warning” pictograms have the following meaning:
Attention! General!
Is an instruction that must be observed in order to ensure protection before, while
and after using the device. The correct procedure must be observed.
Attention! Electric shock!
Persons may be exposed to dangerous voltages in electrical installations.
There is a danger of electric shock if a live part is touched.
Attention! Observe ESD measures!
Electrostatic discharge may destroy electronic components.
Attention! Hot surfaces
Keep clear of surfaces. They may be hot.

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 6/27
1.1.3. Information pictograms indicate the following:
Important information about the product or the relevant section of the document requiring the particular attention of the reader.
The “Information” pictogram has the following meaning:
Indicates important and instructional information.
1.2. Copyright note
This documentation is the intellectual property of Syslogic Datentechnik AG, which also has the exclusive copyright. Any
modification of the content, duplication or reprinting of this documentation, as well as any distribution to third parties can only
be made with the express permission of Syslogic Datentechnik AG.
Syslogic Datentechnik AG does not accept any liability for damages arising from the use of any incorrect or incomplete
information contained in this documentation or any information missing.
All brand and product names are trademarks or registered trademarks of the owner concerned.
1.3. Contents of this Documentation
This document addresses to system integrators, programmers, instructed installation and maintenance personal working with the
system. It provides all information needed to set-up, mount, start-up and operate this device.
1.4. Additional Products and Documents
1.4.1. Software products
There are no additional software products except operating systems:
–Operating Systems: check chapter 4.1 for a list of supported implementations.
1.4.2. Documents
For details regarding the integrated IPC see separate product documentation DOC/COMPACT71-SLE.
1.4.3. Datasheets
For additional and more detailed information on the Intel Atom processor and chipset refer to the following documents:
–Datasheet Intel Atom Processor E6xx Series
http://download.intel.com/embedded/processor/datasheet/324208.pdf#iid=3790
–Specification Update Intel Atom Processor E6xx Series
http://download.intel.com/embedded/processor/specupdate/324209.pdf?iid=3876#iid=3876
–Datasheet Intel Platform Controller Hub EG20T(PCH)
http://download.intel.com/embedded/chipsets/datasheet/324211.pdf#iid=3791
–Specification Update Intel Platform Controller Hub EG20T (PCH)
http://download.intel.com/embedded/processor/specupdate/324209.pdf?iid=3876#iid=3876
–Datasheet Intel 82574 GbE Controller Family
http://download.intel.com/design/network/datashts/82574.pdf
–Datasheet NXP SJA1000
http://www.nxp.com/documents/data_sheet/SJA1000.pdf

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 7/27
1.5. Items delivered
1.5.1. Built-in version
-1x TFT/HBxxxPU71G16-xXXXE
-1x Fixing Frame with M4x10 securing screws
-1x Power supply connector Weidmüller BCZ 3.81/04/180F SN SW (1792970000)
1.5.2. VESA mount version
-1x TFT/HVxxxPU71F16-xXXXE
-1x Power supply connector Weidmüller BCZ 3.81/04/180F SN SW (1792970000)
-4x M4x8 securing screws for VESA100 mounting
1.6. Installation
The installation of the system is described in this documentation.
For details regarding the integrated IPC see separate product documentation DOC/COMPACT71-SLE.
1.7. Safety Recommendations and Warnings
The product is intended for measurement, control and communications applications in industrial environment. The products
must be installed by specially trained people. The strict observation of the installation guideline is mandatory.
The use of the product in systems in which life or health of persons is directly dependent (e.g. life support systems, patient
monitoring systems, etc.) is not allowed.
The use of the product in potentially explosive atmospheres requires additional external protection circuitry which is not
provided with the product.
Important note
Ensure that the power supply is disconnected from the device before working on the
device (connecting interfaces, replacing flash cards, batteries, opening the enclosure,
etc.).
Important note
The output voltage of the external power supply shall be SELV and shall be limited
power source according to clause 2.5 EN 60950-1.
Please read the safety instructions of the power supply before installing/connecting
the device.
In case of uncertainty or of believed errors in the documentation please immediately contact the manufacturer (address see
chapter 7). Do not use or install the product if you are in doubt. In any case of misuse of the product, the user is solely liable for
the consequences.
1.7.1. EMC
Important note
This is a Class A product and not intended to be used in domestic environment. The
product may cause electromagnetic interference. Appropriate measures must be
taken.

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 8/27
1.7.2. Battery
Important note
Caution! Danger of explosion if the battery is not correctly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Never short the battery.
1.7.3. Hot surface
Attention! Hot surfaces
Make sure the device is not hot before mounting or changing the installation. The
device may be hot and may cause burs.
1.8. Electro-Static Discharge
Electronic boards are sensitive to Electro-Static Discharge (ESD). Please ensure that the product is handled with care and only in
a ESD protected environment. Otherwise a proper operation is not guaranteed.
1.9. Life Cycle Information
1.9.1. Transportation and Storage
During transportation and storage the product must be in the original packing. It is recommended, to keep the original packing
in case of return of the product to the factory for repair. Note that the packing is recyclable.
1.9.2. Assembly and Installation
Observe the EMI-precautions against static discharge. Carefully read the installation documentation before unpacking the
product.
The installation procedures must be strictly observed. Note that deviations from the installation guidelines may result in
degraded operational reliability or in unfavourable EM-radiation or EM-susceptibility.
1.9.3. Operation
The operating environment must guarantee the environmental parameters (temperature, power supply, etc.) specified in the
technical specification section of this document.
The main functionality of the product is defined by the application program. The application program is not part of the delivery
by Syslogic but are defined, developed and tested by the customer or a system-integrator for each specific application. Refer to
the respective documentation for more information.
1.9.4. Maintenance and Repair
In the rare case of a product hardware-failure or malfunction, the complete product should be exchanged. The faulty product
must be returned to the factory for repair. Please use whenever possible the original packing for return of the product (EMI and
mechanical protection).
1.9.5. Disposal and WEEE
At the end of the life span the product must be properly disposed. This product contains a multitude of elements and must be
disposed like computer parts. This product contains batteries which should be properly disposed.

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 9/27
The products of the IPC/HxxxxPU71 products are not designed ready for operation for the end-user and intended for consumer
applications. Therefore the Waste Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) is not applicable. But users
should still dispose the product properly at the end of life.
The wrapping contains the following materials: Cardboard box and transportation protection.
Materials
Description
Front Glas
Safety glas
Front Touch
Glas, Plastic, Copper
Front frame
Metal /AlMg 4.5 Mn)
Hoods
Galvanized sheet steel
Mounting plates
Galvanized sheet steel
Display LED
1 Disposal quality
Print boards
1 Disposal quality
Tab. 1 Disposal Materials
1.9.6. Warranty
Our products are covered by a world-wide manufacturer’s warranty. The warranty period starts at the delivery time from our
official distributor to the customer. The duration of the warranty period is specified in the respective product catalogs and the
offers. All products carry a date code and a job number for identification. The manufacturing data and deliveries are registered in
a high level Quality Management System.
The warranty covers material and manufacturing defects. All products must be returned via the official distributor to the factory
for repair or replacement. The warranty expires immediately if the products are damaged by operating outside of the specified
recommended operating conditions. The warranty also expires if the date code or job number listed on the product is altered or
rendered unintelligible. The warranty does not include damage due to errors in firmware or software delivered with the products.
1.9.7. RoHS
The product is designed and produced according to the Restriction of Hazardous Substances (RoHS) Directive (2002/95/EC).

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 10/27
2Product Description
2.1. Introduction
2.1.1. Benefits of Syslogic`s Projected capacitive touch panels
–Different screen sizes
–Robust touch screen technology
–Front protection to IP65
The product meets all the requirements of state-of-the-art advanced Panel Computer.
The product is a rugged information, display and input device that is specially developed for operation in harsh environments.
The TFT technology makes a wide range of applications possible with a perfect and clear picture on an absolutely flat surface.
The absolutely flat PCT (Projected capacitive Touch) touch panel offers the latest Dual-Touch technology. PCT Touch Screen can
be used with fingers or with special capacitive touch gloves or pens/stylus. Calibration of the touch screen can be easily made
with the Touch driver software described in chapter 2.4.
A metal housing with a solid front frame and scratch resistant safety glass protects the device
Reliably during long and rugged periods of use (front protection: IP65) and requires little careand maintenance.
2.1.2. Intended use of Projected Capacitive Touch Panels
The Projected Capacitive Touch Panel is designed for:
–Visualization and process control
–PLC visualization
–General control and automation tasks
–Industrial use
–For medical technology
–For multi-media systems
–Operation in the ambient conditions specified in the technical data
This device description is designed as a reference guide for the installation, connection, operation and maintenance of all
versions of the Projected Capacitive Panel, and also provides all the relevant technical data.

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 11/27
2.2. Device Variants
The Projected capacitive touch panels are available in the following versions:
Order code
Flat screen
Mounting type
Memory
X1 Port
TFT/HB104PU71G16-xxxxE
10.4” XGA
Flush mounting
2GB
RS232
TFT/HB121PU71G16-xxxxE
12.1” XGA
Flush mounting
2GB
RS232
TFT/HB150PU71G16-xxxxE
15.0” XGA
Flush mounting
2GB
RS232
TFT/HV104PU71G16-xxxxE
10.4” XGA
VESA mounting
2GB
RS232
TFT/HV121PU71G16-xxxxE
12.1” XGA
VESA mounting
2GB
RS232
TFT/HV150PU71G16-xxxxE
15.0” XGA
VESA mounting
2GB
RS232
Tab. 2 Projected capacitive touch panel versions
2.3. Accessories
The following accessories are not necessarily supplied with the device. These parts could be ordered additionally or downloaded
under www.syslogic.com:
Accessories
Order code
Type designation
Description
TouchDriver
Touch driver software
Touch driver software for Windows 9x /
Me / 2000 / XP / 7 / Embedded
Tab. 3 Projected capacitive touch panel accessories

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 12/27
2.4. Features
2.4.1. HBxxxPU7F16-xxx
Fig. 1 HBxxxPU71x16-xxx
2.4.2. HVxxxPU71x16-xxx
Fig. 2 HVxxxPU7F16-xxx
Display
DVI
USB 0-3
Ethernet 1
Power
Supply
Ground
Terminal
COM1
RS232
X1
RS232, Rs485 or
CAN
Ethernet 2
Power
Supply
Ground
Terminal
COM1
RS232
X1
RS232, Rs485 or
CAN
Display
DVI
USB 0-3
Ethernet 1
Ethernet 2

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 13/27
W
H
3Hardware Description
3.1. Overview
For details regarding the integrated IPC see separate product documentation DOC/COMPACT7-SLE.
3.2. Dimensions
3.2.1. HBxxxPU71x16-xxx
Device
W [mm]
W1 [mm]
W2 [mm]
H [mm]
H1[mm]
H2 [mm]
D1 [mm]
D2 [mm]
TFT/HB104PU71x16-xxx
288
30
31
234
31
71.5
25
59.5
TFT/HB121PU71x16-xxx
333
52.6
53.6
275
31
112
25
59.5
TFT/HB150PU71x16-xx
395
84.7
83.7
312
31
150.7
29.5
61.5
Tab. 4 HBxxxPU71x16-xxx dimensions
D1
D2
H1
H2
H
W
W1
1mm gap between
mounting frame and
front all around the
display
W2
Nut approx. 4mm

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 14/27
3.2.2. HVxxxPU71x16-xxx
Device #
W [mm]
W1 [mm]
W2 [mm]
H [mm]
H1 [mm]
H2 [mm]
D1 [mm]
D2 [mm]
D3 [mm]
TFT/HV104PU71x16-xxx
278
15
15
224
14
39,5
24.5
58.8
62
TFT/HV121PU71x16-xxx
323
26,5
26,5
265bb
15
67,5
24.5
58.8
62
TFT/HV150PU71x16-xxx
385
57,5
57,5
302
15
104,5
27.5
61.5
65
Tab. 5 HVxxxPU71x16-xxx dimensions
D1
D2
D3
H
W
H1
H2
W1
W2
Frontrahmen rundum 2.5mm
Distanz zum Gehäuse

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 15/27
3.3. Mounting
3.3.1. TFT/HBxxxPU71x16-xxx
To mount the device follow these steps:
1. The desired mounting place must have a cut out and wall thickness regarding the following overview.
Front cut out dimensions
Edge radius
Wall thickness
Device #
W [mm]
H [mm]
R [mm]
D [mm]
TFT/HB104PU71x16-xxx
271 -0/+2
217 -0/+2
Max. 3mm
1 to 5
TFT/HB121PU71x16-xxx
316 -0/+2
258 -0/+2
TFT/HB150PU71x16-xxx
378 -0/+2
295 -0/+2
Tab. 6 TFT/HBxxxPU71x16-xxx Mounting dimensions
Fig. 3 Required Cut out HVxxxPU7F16-xxx
Mounting Angle:
Mounting Angle must be 90°
Cooling Space:
To ensure cooling leave at least 10cm of free space around product.
W
H
R
R
R
R
D

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 16/27
2. Remove the screws highlighted in red and then remove the mounting frame.
Fig. 4 Screws to hold the mounting Frame
3. Insert the projected capacitive touch panel from the front into the cut out and make sure that the sealing fits properly.
4. Reattach the mounting frame and fix it into place by reattaching the screws highlighted in red.
5. The product is now installed properly.
Wall
Projected capacitive touch panel

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 17/27
3.3.2. TFT/HVxxxPU71x16-xxx
All TFT/HvxxxPU71x16-xxx are equipped with a VESA100 (100x100mm) mounting system delivered with M4x8 Philips screws. To
mount the device follow these steps:
1. Remove the screws from the back of the device
2. Screw the device to the VESA100 mounting frame. Maximum thickness of the frame is 3mm. If using a thicker frame
replace the crew. The crew must not fit more than 8mm and must fit least fit 5mm.
Device #
X [mm]
W [mm]
H 1[mm]
H2 [mm]
TFT/HV104PU71x16-xxx
100
89
74
50
TFT/HV121PU71x16-xxx
100
111.5
102
63
TFT/HV150PU71x16-xxx
100
142.5
139
63
Tab. 7 HVxxxPU71x16-xxx VESA dimensions
Mounting Angle:
Mounting Angle must be 90° ± 15°
Cooling Space:
To ensure cooling leave at least 10cm of free space around product.
For best thermal performance use spacer M4 x 5mm between the VESA mounting
frame and the device
X
X
W
H1
W
H2

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 18/27
3.4. Service Cover
To change the battery or the C-Fast follow the steps described in this chaper
3.4.1. TFT/HBxxxPU71x16-xxx
1. To remove the Service Cover remove the two knurled screws highlighted and remove the cover.
2. After removing the cover the C-Fast and the battery slot are accessible.
3. Please install the Service Cover before operating the Projected capacitive touch panel.
3.4.2. TFT/HVxxxPU71x16-xxx
1. To remove the Service Cover remove the two Philips screws highlighted in red and remove the cover.
2. After removing the cover the battery and the C-Fast slot are accessible.
3. Please install the Service Cover before operating the Projected Capacitive Touch Panel.
battery
C-Fast Slot
C-Fast holder
Battery

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 19/27
3.5. Interfaces
3.5.1. Power supply
The processor and its peripherals are powered by a non-isolated, integrated power supply which generates all internal voltages.
Power Supply requirements:
The power supply used must fulfil surge protections according to the
application.
Always use a short circuit protected power supply.
Do not use power supplies wires or cables longer than 3m.
Pin
Signal
Marking
Remarks
1
+24VDC_AUX
VAUX
Additional, permanent power supply
2
Fail/Remote on/off
PF
Power fail input
3
+24VDC
VDC
+10V..+30V
4
GND
GND
GND (/shield)
Tab. 8 Power supply connector P1 (1x4 pin)
For normal operation the external power supply has to be connected to the pins 3 (+24VDC)
and 4 (GND) of the connector P1.
Pin 1 (+24VDC_AUX) is used to extend battery life time if the device main power is disabled.
Pin 2 is used as an input for either a power fail on remote on/off signal.
3.5.2. System Interfaces
For details regarding the integrated IPC interfaces see separate product documentation DOC/COMPACT71-MLE.
3.6. Touch Screen
All devices use a DMC Touch Sensor with an EETI chipset. If the native operating system does not provide required features,
install EETI eGalax Touch driver.
3.6.1. Basic functions of the touch screen
The touch screen operates using the PCT (Projected Capacitive Touch) technology.
Therefore the touch must be manipulated using fingers, special gloves or pens/styluses that are made for use with capacitive
touch panels.
Depending on the driver version and Operating System the PCT touch supports Dual-touch. Which means you can operate the
touch screen with two fingers for drawing or selecting.
The calibration should be carried out with a touch stylus in order to ensure the
optimum functioning of the touch screen.
3.6.2. Using On Screen Keyboard (OSK) with Windows7
When using the On Screen Keyboard (OSK) for Tablet Computer TabTip.exe under Windows 7 you need to use the original
Windows7 driver that is automatically installed instead of the separate touch driver provided by Syslogic to allow TabTip.exe to
work properly.
If you use TabTip.exe in Windows7 instead of OSK.exe you will benefit from some comfort features like automatic activation of
the OnScreenKeyboard when you activate a text input field.
1
4

TFT/HxxxxPU71x16-xxx: user documentation
DOC/Protouch-71; V1.0
© Syslogic Datentechnik AG, CH-5405 Baden-Dättwil, Switzerland, http://www.syslogic.com 20/27
Note:
If you need to use the special features provided by separate touch driver provides you can use OSK.exe instead of TabTip.exe.
But the automatic activation of the On Screen Keyboard when you activate a text input field will not work.
3.6.3. Touch screen calibration using Windows 7 touch driver
To calibrate the touch using the Windows7 with the Windows touch driver execute the following steps:
1. Tap the Start button, Control Panel and then Hardware and Sound.
2. Select Tablet PC Settings, then Calibrate the screen for pen or touch input.
3. On the Display tab select Calibrate located in the section Display Options. Follow the on-screen instructions to
calibrate the touch screen.
3.6.4. Cleaning the glas front
For cleaning the glass front please use a soft cloth and a standard glas cleaning detergent.
Even the touch controller is optimized to detect cleaning it may happen that input
are generated. Prevent unwanted and potentially dangerous actions while the front is
being cleaned.
Prevent the system from unwanted and dangerous while the front is being
cleaned.
3.6.5. Cleaning the metal housing
For cleaning the metal housing please use a soft cloth and a metal polish.
Do not use a coarse scouring cloth, scouring powder or solvent.
Cleaning should only be carried out when the device is switched off!
3.7. Display brightness
Display brightness can be adjusted writing one byte to the I/O register 0x820d. Use the io_rw (Debian, lincan demo) or the
DumpPort (Windows 7, WINIO_v3) to access the register.
Value
Signal
Remarks
0xFF
Maximum Brightness (default)
0x10-0xFE
Brightness from dark to bright
0x00
Backlight turned off
Tab. 9 Meaning of the backlight register.