System air OCWATERLOO PKIR3G Installation instructions

FIRE DAMPER AND FIRE DAMPER FOR EXPLOSIVE AREAS
For explosive areas:
Round - PKIR3G-Ex
Rectangular- PKIS90-Ex / PKIS120-Ex / PKIS3G-Ex / PKIS3GA-Ex
Round - PKIR3G & EKIR
Rectangular- PKIS3G / PKIS3GA / PKIS-EI90S / PKIS-EI120S
ORIGINAL INSTALLATION, OPERATION AND INSPECTION MANUAL
EVERY FIRE DAMPER NEEDS TO BE INSTALLED IN ACCORDANCE WITH THIS MANUAL!
1396 - CPD - 0062
1396 - CPR - 0076
1396 - CPR - 0077
Newest versions of all FSP relevant documents are at www.systemair.com/FSPoverview

2 / 48 | PP-28_201612 | PKIR, PKIS
Installation methods for the round re dampers
Tab. 1: Permitted installation methods for the round re dampers based on re resistivities
NOTES:
* ATEX: When ordering the ATEX re damper, use code PKIR3G-Ex
All ATEX re dampers are rated as explosion proof class
* W: Installation on/ out of a wall with mineral wool, installation method 1.6.2 with EI60S up to DN = 500 mm
Modulated re dampers (activation mechanism DV9-T-SR in Tab. 26) are manufactured: PKIR3G with DN ≥ 160 mm.
IN ACCORDANCE WITH EN 15650 EACH FIRE DAMPER MUST BE INSTALLED ACCORDING TO THE INSTALLATION INSTRUCTIONS PROVIDED
BY THE MANUFACTURER!
Rigid / Flexible wall Only rigid wall / ceiling
Dimension
range (mm) Certicate No. Product type Fire resistivity
Supporting
construction
Installation - tested at underpressure (Pa)
Wet Dry Soft
crossing Instal. kit On a wall Out of a wall
100 ≤ DN ≤ 400 PKIR3G
PKIR3G-Ex *ATEX
EI60 (ve ho i↔o) S
ve 500 300 300 500 300*W300*W
ho 500 300
EI90 (ve ho i↔o) S
ve 500 300 300 500 300*W300*W
ho 500 300
EI120 (ve ho i↔o) S
ve 500 500
ho 500
400 < DN ≤ 630
PKIR3G
PKIR3G-Ex *ATEX
EI60 (ve ho i↔o) S
ve 500 300 300 500 300*W300*W
ho 500
EI90 (ve ho i↔o) S
ve 500 300 300 500
ho 500
EI120 (ve ho i↔o) S
ve 500 500
ho 500
630 < DN ≤ 1000
PKIR3G
PKIR3G-Ex *ATEX
EI60 (ve ho i↔o) S
ve 500 500
ho 500
EI90 (ve ho i↔o) S
ve 500 500
ho 500
EI120 (ve ho i↔o) S
ve 500
ho 500
1396 - CPR - 0076
FTZU14ATEX0127X
1396 - CPD - 0061
FTZU13ATEX0046
FTZU13ATEX0046
1396 - CPR - 0076

PKIR, PKIS | PP-28_201612 | 3 / 48
Installation methods for the rectangular re dampers
Tab. 2: Permitted installation methods for the rectangular re dampers based on re resistivities
NOTES:
* ATEX: When ordering the ATEX re damper use codes with Ex such as PKIS3G-Ex or PKIS90-Ex ...
All ATEX re dampers are rated as explosion proof class
* KIT: up to 800 × 600 mm only
* MULTI: Multi-installation in a wall (method 1.7, Fig. 17) is possible: two dampers beside each other or one above the other, or four
dampers - always with a horizontal axis of the blade
* P: Installation on/out of a wall with Promatect boards (method 1.6.3, 1.6.4) insulation for lower ceiling with resistivity
EI30/45/60/90/S, PKIS3G only up to 800 × 600 mm
* W: Installation on/out of a wall with mineral wool (method 1.6.1 and 1.6.2)
The tightness according to EN 1751: blade class 2 as standard, or upon request class 3 for extra charg; casing class C as standard.
Modulated re dampers (activation mechanism DV9-T-SR in Tab. 26) are manufactured PKIS3G with H ≥ 160 mm.
IN ACCORDANCE WITH EN 15650 EACH FIRE DAMPER MUST BE INSTALLED ACCORDING TO THE INSTALLATION INSTRUCTIONS PROVIDED
BY THE MANUFACTURER!
Dimension
range (mm) Certicate No. Product type Fire resistivity
Supporting
construction
Installation - tested at underpressure (Pa)
Wet Dry Soft
crossing Instal. kit On a wall Out of a wall
100 × 100
up to
1200 × 800
PKIS3G
PKIS3G-Ex *ATEX
EI60 (ve ho i↔o) S
ve 500 300 300 500*KIT 300*W, P 300*W, P
ho 500 300
EI90 (ve ho i↔o) S
ve 500 300 300 500*KIT 300*W, P 300*W, P
ho 500 300
EI120 (ve ho i↔o) S
ve 500 500*KIT 300 i→o
*W, P 300 i←o
*W, P
ho 500
800 < W ≤ 1200
& 100 ≤ H ≤ 300
PKIS3GA
PKIS3G-Ex *ATEX
EI60 (ve ho i↔o) S
ve 300 300*P300*P
ho
EI90 (ve ho i↔o) S
ve 300 300*P300*P
ho
W > 1200
and/or
H > 800
up to
1600 × 1000
PKIS-EI90S *MULTI
PKIS90-Ex *ATEX
PKIS-EI120S
PKIS120-Ex *ATEX
EI90 (ve ho i↔o) S
ve 300 300 300 300*W300*W
ho 300 300 300
EI120 (ve ho i↔o) S
ve 300
ho 300 300
FTZU14ATEX0127X
1396 - CPR - 0077
1396 - CPR - 0077
FTZU13ATEX0046
1396 - CPD - 0062
Rigid / Flexible wall Only rigid wall / ceiling

4 / 48 | PP-28_201612 | PKIR, PKIS
S
ø
D
1
1
S
W
1
H
1
1
Fig. 1: RRW – Solid wall / ceiling with a round opening Fig. 2: RSW – Solid wall / ceiling with a rectangular opening
1Concrete, Masonry, Cellular concrete
Legend
Fire resistivity
(min.)
s(mm)
Wall Ceiling
Concrete, Masonry Cellular Concrete Concrete Cellular Concrete
60 110 ± 10 110 ± 10 110 ± 10 125 ± 10
90
120 150 ± 10 150 ± 10 150 ± 10 150 ± 10
Tab. 3: Thickness of standardized walls / ceilings under EN 1366-2
NOTE: Dimensions øD1, W1, H1 are dened in every installation by Tab. 5 through 24

PKIR, PKIS | PP-28_201612 | 5 / 48
m
ax.
6
2
5
S
2
4
ø
D
1
1
3
□
D
2
m
ax.
6
2
5
2
4
1
3
S
H
1
W1
Fig. 3: FRW – Flexible (plasterboard) wall
with a round opening
Fig. 4: FSW – Flexible (plasterboard) wall
with a rectangular opening
1Plasterboard reproof plate, thickness 12,5 mm / 2 layers
2Vertical CW - proles (prole width sCW based on re resistivity, see Tab. 4), maximum spacing in the opening area 625 mm.
3Horizontal CW - proles (prole width sCW based on re resistivity, see Tab. 4), must be rmly embedded into the vertical proles
4Mineral wool thickness / cubic weight see Tab. 4
Legend
Fire resistivity
(min.)
ssCW
Insulation – mineral wool
Thickness Cubic density
(mm) (kg/m3)
60 100 50 40 40
90 125 75 60 50
120 150 100 60 100
Tab. 4: Thickness of standardized walls and layers according to EN 1366-2
NOTE: Dimensions øD1, W1, H1 are dened in every installation by Tab. 5 through 24

6 / 48 | PP-28_201612 | PKIR, PKIS
Fig. 5: Wet installation of a round re damper PKIR3G using a mixture of plaster with mortar or concrete
Wall
and opening type
Dimensions of the
openings øD1
Dimensions of the
internal frame □D2
(mm)
RRW øDN + 80 -
FRW øDN + 80 □DN + 100
Nominal dimension
DN (mm)
LD(mm)
ZV, DV1 through DV6 DV7 - DV9
100 - 400 210
450
282
192
500
242
560
630 - 1000 342
1Bendable hanger
2Plaster / mortar / concrete lling
3Screw 5,5 DIN7981
Legend
Tab. 5: Wall opening
NOTE: øD1 , W1 , H1 see Fig. 1 – 4
Tab. 6: Distance of the connected duct’s ending from the wall
WET - gypsum/mortar/concrete - EI120S 1.1
L
D
3
1
2
øDN

PKIR, PKIS | PP-28_201612 | 7 / 48
1.1 WET - gypsum/mortar/concrete - EI120S
Fig. 6: Wet installation of a rectangular re damper PKIS using a mixture of plaster with mortar or concrete
Wall and
opening type Dimensions of the openings W1× H1(mm) Dimensions of the
internal frame (mm)
RSW W + 120 × H + 120 -
FSW W + 120 × H + 120 W + 120 × H + 120
LD(mm)
PKIS3G PKIS-EI60S PKIS-EI90S PKIS-EI120S
185 254
1Bendable hanger
2Plaster / mortar / concrete lling
3Screw 5,5 DIN7981
Legend
Tab. 7: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 – 4
Tab. 8: Distance of the damper’s ending from the wall
2
3
1
H
W
L
D

8 / 48 | PP-28_201612 | PKIR, PKIS
Fig. 7: Dry installation of a round re damper PKIR3G using mineral wool with coverplates
Wall and
opening type Dimensions of the openings øD1 (mm) Dimensions of the in-
ternal frame □D2(mm)
RRW øDN +120 -
FRW øDN + 120 □DN + 120
Nominal dimension
DN (mm)
LD(mm)
ZV, DV1 through DV6 DV7 - DV9
100 - 400 230
450
282
192
500
242
560
630 - 1000 342
1Bendable hanger
2Mineral wool lling (min. 50 kg/m3)
3Screw 5,5 DIN7981
4Coverplate PRR-PKI (accessories)
5Screw 5,5 DIN7981
6Fire resistive mastic, e.g. Intumex AC
Legend
Tab. 9: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 – 4
Tab. 10: Distance of the connected duct’s ending from the wall
DRY - mineral wool - EI90S 1.2
3
4
2
4
L
D
øDN
5
6
6
1

PKIR, PKIS | PP-28_201612 | 9 / 48
4
2
4
H
W
L
D
3
1
6
5
6
1.2 DRY - mineral wool - EI90S
Fig. 8: Dry installation of a rectangular re damper PKIS using mineral wool with coverplates
Wall and
opening type Dimensions of the openings W1× H1(mm) Dimensions of the
internal frame (mm)
RSW W + 120 × H + 120 -
FSW W + 120 × H + 120 W + 120 × H + 120
LD(mm)
PKIS3G PKIS-EI60S PKIS-EI90S PKIS-EI120S
205 254
3 1 4
PKIS-EI90S PKIS3G
5
3 14 5
2
1Bendable hanger 2Mineral wool lling (min. 50 kg/m3)
3Screw 5,5 DIN7981 4Coverplate PRS-PKI (accessories) 5Screw 5,5 DIN7981 6Fire resistive mastic, e.g. Intumex AC
Legend
Tab. 11: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 - 4
Tab. 12: Distance of the damper’s ending from the wall

10 / 48 | PP-28_201612 | PKIR, PKIS
Fig. 9: Installation of a round re damper PKIR3G into a soft crossing
Wall and
opening type Dimensions of the openings øD1(mm) Dimensions of the in-
ternal frame □D2(mm)
RRW øDN + 120 -
FRW øDN + 120 □DN + 120
Nominal dimension
DN (mm)
LD(mm)
ZV, DV1 through DV6 DV7 - DV9
100 - 400 210
450
282
192
500
242
560
630 - 1000 342
1Bendable hanger
2Mineral wool segment (150 kg/m3)
3Screw 5,5 DIN7981
4Layer of re resistive mastic (e.g. Intumex AC)
at least 2 mm thick
Legend
Tab. 13: Wall opening
NOTE: øD1 , W1 , H1 see Fig. 1 - 4
Tab. 14: Distance of the connected duct’s ending from the wall
SOFT CROSSING - mineral wool - EI90S 1.3
4
3
1
L
D
m
in.
1
0
0
m
i
n
.
1
0
0
øDN
2
m
i
n
.
1
0
0

PKIR, PKIS | PP-28_201612 | 11 / 48
1.3 SOFT CROSSING - mineral wool - EI90S
Fig. 10: Installation of a rectangular re damper PKIS into a soft crossing
Wall and
opening type Dimensions of the openings W1× H1(mm) Dimensions of the
internal frame (mm)
RSW W + 120 × H + 120 -
FSW W + 120 × H + 120 W + 120 × H + 120
LD(mm)
PKIS3G PKIS-EI60S PKIS-EI90S PKIS-EI120S
185 254
1Bendable hanger
2Mineral wool segment (150 kg/m3)
3Screw 5,5 DIN7981
4Layer of re resistive mastic (e.g. Intumex AC)
at least 2 mm thick
5L-prole 60 × 40 × 3 mm (see chapter 1.3)
6Screw 5,5 DIN7981
7Screw 3,9 × max.13 DIN7504
Legend
Tab. 15: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 - 4
Tab. 16: Distance of the damper’s ending from the wall
4
2
7
3
5
6
L
D
H
W
1
4
m
i
n
.
1
00
min
.
10
0

12 / 48 | PP-28_201612 | PKIR, PKIS
Fig. 11: Installation of a round re damper PKIR3G using an installation kit
Wall and
opening type
Dimensions
of the openings øD1± 1
W1× H1± 1 (mm)
Dimensions
of the internal
frame (mm)
Suitable
installation kit
RRW øD1 (Tab. 19) - IKRR-PKI
FSW * W1× W1 (Tab. 19) W1+ 50 × W1+ 50 IKRS-PKI
Tab. 17: Wall opening
NOTES: øD1, W1, H1 see Fig. 1 - 4
* Internal surfaces of the opening need to be covered by two layers (12,5 mm) of plasterboard across their entire perimeter
** Distance of the connected duct’s ending from the wall
1Screw 5,5 DIN7981
Legend
INSTALLATION KIT - insulation assembled from factory - EI120S 1.4
1
26
5
*
*
m
in.100
øDN

PKIR, PKIS | PP-28_201612 | 13 / 48
1.4 INSTALLATION KIT - insulation assembled from factory - EI120S
Fig. 12: Installation of a rectangular re damper PKIS3G using an installation kit
Wall and
opening type Dimensions of the ope- nings W1× H1± 1 (mm) Dimensions of the
internal frame (mm)
RSW W + 100 × H + 100 -
FSW * W + 100 × H + 100 W + 150 × H + 150
Tab. 18: Wall opening
NOTES: øD1, W1, H1 see Fig. 1 - 4
* Internal surfaces of the opening need to be covered by two layers (12,5 mm) of plasterboard across their entire perimeter
1Screw 5,5 DIN7981
Legend
1
185
H
W

14 / 48 | PP-28_201612 | PKIR, PKIS
Fig. 13: Installation kit shapes (IKRR-PKI, IKRS-PKI, IKSS-PKI)
DN
W1W2W3øD1øD2
(mm)
100 200 350 187 200 187
125 250 375 237 250 237
150 400
180 300 430 287 300 287
200 450
225 350 475 337 350 337
250 500
280 400 530 387 400 387
315 565
355 450 605 437 450 437
400 500 650 487 500 487
450 550 700 537 550 537
500 600 750 587 600 587
560 660 810 647 660 647
600 700 850 687 700 687
630 730 880 717 730 717
Tab. 19: Dimensions of the installation kit and opening
in the wall
NOTE: øD1, W1, H1 see Fig. 1 - 4
Installation kit can not be delivered separately. The deli-
very is always with the damper as a complete assembly.
Rectangular instal. kit only up to 800 × 600 mm.
IKRR-PKI IKSS-PKIIKRS-PKI
INSTALLATION KIT - insulation assembled from factory - EI120S 1.4
øD2
øDN-2,5
120
435
265
W2×W2
~150
30
ø6,2
W3×W3
øDN-2,5
120
435
265
W2×W2
~150
30
ø6,2
W×H
95
(W+88)×(H+88)
126
325
185
(W+250)×(H+250)
~150
30
ø6,2
2
3
40
PKIR3G
1

PKIR, PKIS | PP-28_201612 | 15 / 48
Fig. 14: Installation of a round re damper PKIR3G
100 ≤ DN ≤ 630 mm on a wall and out of a wall
NOTE: This picture is valid for LD = max. 1500 mm from
the damper’s ending. For LD> 1500 mm the maximum
spacing between threaded rods must be 1500 mm and
one more point of suspension must be added in the
position of damper blade as close as possible to the end
of the damper.
Wall and
opening type Dimensions of the openings øD1(mm)
Dimensions of the
internal frame
□D2(mm)
RRW øDN+120 -
FRW øDN+120 □DN+120
Tab. 20: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 - 4
1Steel threaded rod M12
2Sheet metal ringlet for damper suspension
(e.g. MP-MX/HILTI)
3Ceramic tape (e.g. A-KERA) width 40 mm, thickness 2 mm
4Sheet metal belt 40 × 2 mm bent into a shape L
with sides 35 and 160 mm
5Screw 5,5 DIN7981
6Screw 3,9 × max. 13 DIN7504
7Mineral wool (66 kg/m3) - in a wall
8Layer of re resistive mastic (e.g. Intumex AC)
at least 2 mm thick
9Mineral wool (66 kg/m3) - inner layer
10 Mineral wool (66 kg/m3) - outer layer
11 Steel binding wire thickness 1,6 mm
12 Insulation front cover*
Legend
* Accessory IPOR-PKI (see TPI-28)
1.5.1 ON A WALL &1.6.1 OUT OF A WALL - Mineral wool - EI90S
8
9
7
12
11
1
80
1
5
0
6
45
110
6
øDN
17
0
4
0
15
5
L
D
2
3
40
PKIR3G
1

16 / 48 | PP-28_201612 | PKIR, PKIS
Fig. 15a: Installation of a rectangular re damper PKIS on a wall
and out of a wall
NOTES: This picture is valid for LD = max. 1500 mm from the damper’s
ending. For LD> 1500 mm the maximum spacing between threaded rods
must be 1500 mm and one more point of suspension must be added in
the position of damper blade as close as possible to the connection ange.
16
15
617 16 11
PKIS-EI90S
ON A WALL 1.5.1 &OUT OF A WALL - Mineral wool - EI90S 1.6.1
9
8
7
6
4
5
11
12
10
1
13 14
2
39
L
D
1
5
0
c
1
4
0
b
a
H
W
18
2
3
18
2
2
31
1
PKIS3G

PKIR, PKIS | PP-28_201612 | 17 / 48
1Steel threaded rod M10
2U-prole (e.g. MQ31/HILTI)
3Calcium-silicate board 60 × 20 mm *
4Steel L-prole 60 × 40 × 3 mm
5Screw 5,5 DIN7981
6Screw 3,9 × max. 13 DIN7504
7Mineral wool (66 kg/m3) - in a wall
8Layer of re resistive mastic (e.g. Intumex AC)
at least 2 mm thick
9Mineral wool (66 kg/m3) - inner layer
10 Mineral wool (66 kg/m3) - outer layer
11 Welding pin – length 90 or 100 mm **
12 Welding pin – length 180 or 200 mm **
13 Insulation front cover *
14 Screw 3,9 × max. 13 DIN7504
15 IPOS-PKI hanging steel frame made of tubular
proles 60 × 40 × 3 mm *
16 Sheet metal 85 × 40 × 2,5 mm
17 Damper insulation frame’s screw
18 Steel threaded rod M8
Legend (Fig. 15a)
* Part of the accessory IPOS-PKI (see TPI-28); ** top without welding pins, side 20 pins/m2, bottom 20 pins/m2;
distance between pins max. 260 mm, distance of the pin from the edge 80 mm
Selection dimensions in
mechanism’s protective covers PKIS3G PKIS-EI90S
a40 65
b155 320
c180 200
Wall and
opening type Dimensions of the openings W1× H1(mm) Dimensions of the
internal frame (mm)
RSW W + 120 × H + 120 -
FSW W + 120 × H + 120 W + 120 × H + 120
Tab. 21a: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 - 4
Tab. 21b: Dimensions of the roundup for the mechanism in protective covers
1.5.1 ON A WALL &1.6.1 OUT OF A WALL - Mineral wool - EI90S

18 / 48 | PP-28_201612 | PKIR, PKIS
Fig. 15b: Installation of a round re damper PKIR3G 100 ≤ DN ≤
500 mm on a wall and out of a wall - re resistivity EI60S
NOTE: This picture is valid for LD = max. 1500 mm from the
damper’s ending. For LD> 1500 mm the maximum spacing bet-
ween threaded rods must be max. 1500 mm and one more point
of suspension must be added as close as possible to the end of
the damper.
Wall and
opening type Dimensions of the openings øD1(mm)
Dimensions of the
internal frame
□D2(mm)
RRW øDN+120 -
FRW øDN+120 □DN+120
Tab. 22a: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 - 4;
wall type RRW and FRW see Tab. 3 - 4
1Steel threaded rod M12
2Sheet metal ringlet for damper suspension
(e.g. MP-MX/HILTI)
3Standard sheet metal ringlet for damper suspension (2×)
4Mineral wool (66 kg/m3)
5Layer of re resistive mastic (e.g. ISOVER Protect
BSF) on both side at least 2 mm thick
6Mineral wool th. 100 (66 kg/m3 ; e.g. ISOVER
Ultimate U-ProtectWiredMat 4.0Alu1)
7Aluminium tape around the front side and on
places uncovered with alufoil
8Layer of re resistive glue (e.g. ISOVER Protect BSK)
9Wire clamp for U-ProtectWiredMat xation
Legend
LD
5
4
3
1
0
0
1
6
7
øD
N
8
2
2
PKIR3G
1
9
ON A WALL 1.5.2 &OUT OF A WALL - Mineral wool - EI60S 1.6.2

PKIR, PKIS | PP-28_201612 | 19 / 48
1.5.2 ON A WALL &1.6.2 OUT OF A WALL - Mineral wool - EI60S
Fig. 15ba: Installation of a rectangular re damper
PKIS3G on a wall and out of a wall - re resistivity EI60S
NOTES: This picture is valid for LD = max. 1500 mm from
the damper’s ending. For LD> 1500 mm the maximum
spacing between threaded rods must be max. 1500 mm
and one more point of suspension must be added as
close as possible to the connection ange.
L
D
8
0
H
W
6
5
4
3
1
2
8
L
S
5
7
9
Wall and
opening type
Dimensions
of the openings
W1× H1(mm)
Dimensions
of the internal
frame (mm)
RSW W + 120 × H + 120 -
FSW W + 120 × H + 120 W + 120 × H + 120
1Steel threaded rod M10
2U-prole (e.g. MQ31/HILTI) Top & Bottom
3Mineral wool (66 kg/m3)
4Layer of re resistive mastic (e.g. ISOVER Protect BSF)
on both side at least 2 mm thick
5Layer of re resistive glue (e.g. ISOVER Protect BSK)
6Mineral wool th. 80 mm (min. 66 kg/m3;
e.g. ISOVER Ultimate U-Protect Slab 4.0 Alu1)
7Welding pin – length 80 mm *
8Stiffening rods: horizontal for W > 600 mm;
vertical for H > 400 mm. **
9Aluminium tape around the front side
and on places uncovered with aluminium foil
Legend
Tab. 22b: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 - 4
* Top without welding pins, side 20 pins/m2,
bottom 20 pins/m2; distance between pins max. 260 mm,
distance of the pin from the edge 80 mm
** Along the insulated duct - the rst stiffening rod is placed
inside the wall. Each subsequent stiffening rod must be placed
with an LS distance = max. 1000 mm. The last stiffening rod must
be placed 1000 mm from the re damper ange at most. If the
re damper ange is closer to the wall than the overhang of the
open blade (R2 ; see Tab. In TechSpec_TPI-28...), then move the
rst stiffening rod to the right so that the distance between the
stiffening rod and the re damper ange is R2 + 50 mm.

20 / 48 | PP-28_201612 | PKIR, PKIS
Fig.15c: Installation of a rectangular re damper PKIS3G or PKIS3GA on a wall and out of a wall with Promatect boards
- resistivity EI90S
H
W
1
8
0
m
i
n
.
1
00
m
i
n.
10
0
8
0
LD
9
8
7
4
10
3
6
6 521
Wall and
opening type Dimensions of the openings W1× H1(mm) Dimensions of the
internal frame (mm)
RSW W + 120 × H + 120 -
FSW W + 120 × H + 120 W + 120 × H + 120
1Steel threaded rod M10
2U-prole (e.g. MQ41/HILTI)
3Calcium-silicate board th. 40 mm;
e.g. Promatect L500/Promat
4Calcium-silicate board th. 40 mm; width min. 100 mm;
e.g. Promatect L500/Promat
5Installation kit IKOWS – W × H (details see Fig. 15e)
6Fire protection glue; e.g. Promat kleber K84/Promat
7Gypsum board th. 15 mm; width min. 100 mm
8Steel L-prole 25 × 25 × 2 mm
9Mineral wool th. 50 mm / 150 kg/m3
10 Screw 5 × 80; DIN7997
Legend
Tab. 23: Wall opening
NOTE: øD1, W1, H1 see Fig. 1 - 4
ON A WALL 1.5.3 &OUT OF A WALL - Promatect - EI90S 1.6.3