T3 SinglePass X User manual

SINGLEPASS X
User Guide
1.5"wide iron
Model No. 73541

2
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
KEEP AWAY FROM WATER
Electricity and water are a dangerous combination and can
cause death by electric shock. Do not allow electrical cords to
come into contact with water or other liquids.
ELECTRICAL APPLIANCES ARE ELECTRICALLY LIVE WHEN
PLUGGED IN, EVEN IF TURNED OFF.
To reduce the risk of death by electric shock:
1. Always unplug the appliance immediately after using.
2. Do not use while bathing.
3. Do not place or store the appliance where it can fall or be
pulled into a bath tub or sink.
4. Do not place in or drop into water or other liquid.
5. If the appliance falls into water, unplug it immediately. Do not
reach into the water.
READ ALL INSTRUCTIONS BEFORE USING
When using electrical appliances, especially when children are
present, basic safety precautions should always be followed,
including the following:

3
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
To reduce the risk of burns, electrocution, fire or injury to
persons:
1. An appliance should never be left unattended when plugged
in.
2. Close supervision is necessary when this appliance is used
on, or near children or individuals with certain disabilities.
3. Use this appliance only for its intended use as described in
this manual. Do not use attachments not recommended by
the manufacturer.
4. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, or if it has been dropped,
damaged, or dropped into water. Return the appliance to a
service center for examination and repair.
5. Keep the cord away from heated surfaces. Do not wrap the
cord around the appliance.
6. Never use while sleeping.
7. Never insert any object into the styling iron.
8. Do not use outdoors or operate where aerosol (spray)
products are being used or where oxygen is being
administered.
9. Do not use an extension cord with this appliance.
10.This styling iron is hot when in use. Do not let eyes and bare
skin touch the heated surfaces.

4
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
11. Do not place the heated styling iron directly on any surface
while it is hot or plugged in.
12. Do not use if the plug is loose in the outlet, as there may be
risk of fire, electric shock, electrical shortage and burning.
13. Make sure to remove the plug from the wall outlet after use.
Do not use the appliance near a bath tub, washbasin
or other vessel filled with water. Never place the
appliance in water or any other liquid.
SAVE THESE INSTRUCTIONS

5
ENGLISH
MAINTENANCE INSTRUCTIONS
SINGLEPASS X
1. Your appliance is virtually maintenance free. It contains no
user serviceable parts, and no lubrication is needed.
2. Keep heated surfaces clean and free of dust, dirt & hairspray.
3. If cleaning becomes necessary, disconnect the appliance
from the power source and let it cool. Wipe the exterior with a
damp cloth.
4. If any malfunction occurs, unplug the appliance, allow it to
cool and return it to a service center to repair.
5. Never wrap the cord around the appliance since this will
cause the cord to wear prematurely and break. If the cord
becomes twisted, untwist it prior to use.
6. Handle the cord carefully for longer life and do not put any
stress on the cord where it enters the handle. Avoid jerking,
twisting or straining especially at the plug connections. It
could cause the cord to fray and possibly break.
7. Do not attempt to repair the appliance yourself.
STORAGE
When not in use, your styling iron should be disconnected and
stored in a safe, dry location, out of reach of children. Do not
wrap the cord around the styling iron. Allow the cord to hang or
lie loose and straight at the point of entry into the styling iron.

6
ENGLISH
This appliance is intended for household use.
Use on Alternating Current (60/50 Hz) only.
This appliance has a polarized plug (one blade is wider than the
other). As a safety feature, this plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Do
not attempt to defeat this safety feature.
AUTO SHUT-OFF
After approximately one hour, the unit will automatically shut
itself off. To reactivate the unit, press the Power & Temperature
Adjustment Button.
AUTO WORLD VOLTAGE
This appliance contains a special electronic circuit that
automatically converts it for worldwide usage - from 100VAC 60
Hz to 240VAC 50 Hz. Just plug it into the local power outlet and
use it as normal; the styler will automatically adjust to the local
current. You may need an adapter to allow the plug to fit into the
local outlets.
Note: Tool heat up time may vary based on country and voltage.
OPERATING INSTRUCTIONS
SINGLEPASS X

7
ENGLISH
OPERATING INSTRUCTIONS
SINGLEPASS X
Electrical Cord
Heating Plate
2 Sectioning Clips
(included)
Main Body
Power & Temperature
Adjustment Button
Operating Display
Plug

8
ENGLISH
OPERATING INSTRUCTIONS
SINGLEPASS X
1Press the Power & Temperature
Adjustment Button using AUDIO
MODE or SILENT MODE to turn the
iron on. You will hear a tone and the
lights on the iron will cascade up.
OPERATING MODE
Audio Mode: Click the Power & Temperature Adjustment Button
quickly to begin operation.
Silent Mode: Hold the Power & Temperature Adjustment Button
down 2 seconds to begin operation.
Changing Modes: Turn the iron off first, and then turn on the
iron using Audio Mode or Silent Mode operation.
The Heating Plates will become very hot within a few seconds.
Avoid contact with skin to prevent burns.

9
ENGLISH
OPERATING INSTRUCTIONS
SINGLEPASS X
2
3
The temperature lights and T3 logo will
turn solid when the iron is ready to use and
you will hear a long tone. Upon first use,
the iron will automatically heat up to 351ºF,
indicated by 3 solid lights.
Note: Each time you turn the iron on, it will
heat up to the last set temperature.
To turn off the iron, hold the Power &
Temperature Adjustment Button downfor 2
seconds. You will hear a tone and the lights
on the iron will cascade down.
Note: You cannot turn the iron off when
you are in the TEMPERATURE ADJUSTMENT
MODE.

10
ENGLISH
OPERATING INSTRUCTIONS
SINGLEPASS X
TEMPERATURE ADJUSTMENT MODE
While the iron is on, adjust the temperature
by double clicking the Power & Temperature
Adjustment Button. You will hear a tone and
the lights will flash.
Continue to click the button to cycle through
the temperature settings. When you reach
the desired setting, release the button.
After several seconds you will hear another
tone, the selected temperature light(s)
will flash and the lights will cascade up
or down as the iron is adjusting to the
selected temperature.
When the iron has reached your set temperature, you will hear three
tones indicating the iron is ready to use.

11
ENGLISH
OPERATING INSTRUCTIONS
SINGLEPASS X
SELECT THE RIGHT TEMPERATURE
Select the right temperature for your hair type using the chart below.
When using the iron for the first time, it is recommended that you
start at the lowest setting and gradually increase the temperature
based on your needs. Never style hair for the first time on a high
setting as this may damage your hair.
TEMPERATURE SETTINGS
*Hair that has not been chemically treated
Coarse, curly
or virgin* hair
Normal
hair
410°F
210°C
390°F
199°C
351°F
177°C
300°F
149°C
261°F
127°C
Fine, damaged or
chemically treated hair

12
ENGLISH
HOW TO USE YOUR
SINGLEPASS X
1
2
Hair should be completely dried
before using the iron. Then use a
brush or comb to detangle hair.
Twist the top part of your hair out
of the way and secure it with one
of the included sectioning clips.
Gather the rest of your hair into the
other clip, leaving a thin section out
to begin styling.
To avoid kinks, style your hair using
thin, horizontal sections* so the
iron can be positioned close to the
roots.
Prep Your Hair
Section Your Hair
Hair section should be as wide as the plate length.
Hair section should be
as thick as the plate.
*Expert Tip:

13
ENGLISH
HOW TO USE YOUR
SINGLEPASS X
3Take the hair section and pull it taut
starting at the root. Clamp the iron
close to the roots and glide the iron
through slowly*.
Repeat with each section until hair
is fully styled.
To avoid burns, do not allow the
iron to touch the scalp.
Glide Slowly
Slow down for perfect results in a single glide:
Fine hair: Glide iron at 2-3 inches per second
Medium Hair: Glide iron at 2 inches per second
Coarse Hair: Glide iron at 1 inch per second
*Expert Tip:

14
ENGLISH
T3 LIMITED WARRANTY
TERMS & CONDITIONS
T3 Micro will repair or replace (at our option) T3 products for twenty-
four (24) months from the date of purchase if they are defective in
workmanship or materials. This limited warranty does not cover (1)
damage due to misuse or abuse, such as incorrect voltage supply,
dropping, or failure to follow enclosed instructions or (2) tampering,
such as repair or attempt to repair. To obtain service under this
warranty, please visit t3micro.com/warrantyclaim to submit a
warranty claim, or call us at [phone] to receive detailed
instructions. You will be required to provide proof of purchase.
THIS LIMITED WARRANTY IS ONLY VALID IF THE PRODUCT IS
PURCHASED FROM AN AUTHORIZED SELLER OF T3 GOODS AND IF
THE ORIGINAL SERIAL NUMBER ON THE PRODUCT HAS NOT BEEN
REMOVED OR OTHERWISE TAMPERED WITH.
Any implied warranties, obligations, or liabilities, including but not
limited to the implied warranty of merchantability and fitness for
a particular purpose, shall be limited in duration to the 24 month
duration of this written limited warranty. Some states do not allow
a limitation on how long an implied warranty lasts, so the above
limitation may not apply to you.
IN NO EVENT SHALL T3 BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED.
Visit www.t3micro.com/register to complete your warranty
registration.

MODEL NO.
73541
SPECIFICATIONS
Operating Voltage: 120240V, 6050 Hz
Power Consumption: 48W
T3 Micro, Inc.
Venice, CA USA
Made in China
018473541B

Model: 73541
This device complies with Part 15 of the FCC Rules:
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
(2) and (2) this device must accept any interference
received, including interference that may cause
undesired operation.