Takara Belmont apollo 2 User manual

Thank you for choosing TAKARA BELMONT equipment.
Please read through this manual before assembling, installing or using the product to ensure safe and correct
use. This product is designed for commercial use in hairdressing and beauty salons. Do NOT use this product
for purposes other than the practices and services typically offered in these places.
Please keep this manual in a safe place for your future reference.
A PDF version of this manual can be downloaded at takarahairdressing.co.uk/downloads
Hydraulic Chair Manual
Apollo 2
Takara Belmont UK Ltd. Belmont House, 1 St. Andrews Way, Bow, London E3 3PA UNITED KINGDOM
takarahairdressing.co.uk T: [phone] E: [e-mail]

Assembling the U-shape and T-shape footrest
1. Locate and remove the attached screws from the underside of the chair top > 2. Attach the footrest to the position
where the screws were attached > 3. Tighten firmly > 4. Check that the footrest is attached securely.
1. Lock the chair using the foot pedal before lifting > 2. Carry the chair by holding it beneath the base > 3. Place
the chair down gently, being careful not to mark the floor > 4. Lift the chair carefully into its final position.
Assembling the chair top with the base
If the chair is used without the pin inserted firmly into the ditch,
the chair may become unstable resulting in damage or injury.
Safety precautions during installation
The chair must be installed on a flat and solid floor to ensure its stability.
At least two people should assist with carrying or moving a chair at all times.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Chair top
Chair base
Line up the ditch
to the pin and insert
the seat flange firmly.
• When assembling the footrest, do NOT use any screws other than those provided by Takara Belmont (located on the underside of chair top).
• Ensure all screws are tightened firmly. If the footrest is not attached to the chair firmly, it will become unstable and may result in damage or injury.
• Take care not to damage the upholstery or the chair parts during assembly: the chair top should be kept separate from the assemblage area.
> Please note, these drawings are for illustrative purposes only.
• Carefully position the chair base on a flat and solid floor.
• Present the chair top to the base, line up the ditch to the pin
and insert the seat flange firmly.
• Check that the chair top is attached securely.
• Do NOT apply any weight or stress to the armrest while carrying or
moving the chair to avoid breakage or deformation to the armrests.
• Do NOT hold and move the chair with somebody or something in the
seat.
• Take care when touching the underside of the chair top. Parts such
as fixing screws, fasteners, metal parts are attached here and careless
contact may result in injury.
• Carrying the chair by gripping the chair top is likely to cause the chair
base to slip off and may result in serious injury.

Seat front
Seat rear
Attachment
positions x4
Screws
U-shape
Footrest
U-shape
Footrest
T-shape
Footrest
Screws Screws
Seat rear
Seat front
Attachment
positions x4
Seat front
Attachment
positions x2
Seat rear

Safety precautions during operation
These precautions are provided for the safe use of this product and to prevent personal injury to users.
Do NOT lean on the chair carelessly, climb on the seat, or sit on the armrest to avoid unbalancing or
unintentionally rotating the chair, resulting in damage or injury.
For ease and comfort, ensure that your customers enter and exit the chair at its lowest position.
For comfort and stability while seated, recommend your customers to keep their feet on the footrest.
Symbols key:
Raising, lowering and rotating the chair
To avoid damage or injury, please observe the following advice:
• Before raising or lowering the chair, ensure that there are no people or
objects obstructing the chair, foot pedal or footrest.
• Before rotating the chair, ensure that there are no people or objects
including cables obstructing the chair, foot pedal or footrest.
• Before rotating the chair, ensure that the customer’s feet are not
going to be pinched between the footrest and the foot pedal. Advise your
customer to place their feet on the footrest securely.
• Operate the foot pedal with appropriate force to avoid hitting the
backrest with your knee.
Entering and exiting the chair
To avoid toppling the chair resulting in damage or injury, please
observe the following advice:
• Do NOT apply a load of 30kg or over to the tip of the footrest and do NOT
jump on the footrest even if the load is less than 30kg.
• Do NOT step on the tip of the footrest.
• Do NOT enter or exit the chair by stepping on the footrest.
To avoid customer injury as a result of chair use, please observe
the following advice:
• Pay attention to the chair base when entering and exiting the chair to
avoid tumbling which may result in injury.
• Take care that your customer’s exit is not obstructed by the foot pedal
or footrest to avoid tumbling which may result in injury.
To avoid damage or injury from accessories such as hairdryers,
please observe the following advice:
• Take care NOT to hook or tangle any cables around the underside of the
chair top, armrests or backrest.
OPERATION INSTRUCTIONS
Hydraulic base operation
Operate the foot pedal with appropriate force.
Observe the safety precautions shown below.
Adjusting the height
To avoid damage or injury, please
observe the following advice:
• Before raising or lowering the
chair, ensure that there are no
people or objects obstructing the
chair, foot pedal or footrest.
RAISE
Pump gently
to raise the seat
UNLOCK
Gently press down
to unlock
LOWER
Gently press down and hold
to lower the seat
ROTATE
Swivel the chair carefully
with two hands
LOCK
Gently press upwards and hold,
to lock the chair in place
LOCK
Gently press upwards and hold,
to lock the chair rotation
Rotating the chair
To avoid damage or injury, please
observe the following advice:
• Before rotating the chair, ensure
that there are no people or objects
including cables obstructing the
chair, foot pedal or footrest.

Daily Maintenance
• Do NOT use leather cleaner containing solvents or abrasives. The
surface may degrade, leading to changes in the texture and luster.
• Do NOT use volatile chemicals such as thinners, alcohol, benzene, nail
polish remover, gasoline or kerosene, abrasive wax, abrasive sponges
and so on.
• Do NOT use brushes or scouring pads.
• Make sure that cleaning utensils do NOT contact the product during
general cleaning. Neglecting this caution may result in deterioration or
breakage of the product.
Daily Inspections
The following inspections should be carried out every day to
ensure safety during use and the longevity of the equipment:
Notes
Please observe the following.
The standard period of use for this product is seven years:
The ‘standard period of use’ is a guide to a standard period of time that
the product can be expected to perform under normal salon conditions,
assuming regular inspections and any appropriate maintenance
(including parts replacement) has been performed during this period.
Note: this is not a warranty period.
• No parts are specified as “consumable” for this product.
• Scratches, dirt, deterioration and corrosion of the exterior parts stated
below are not covered by warranty:
– upholstery including the vinyl, cushioning, threads, etc.
– all other exterior parts
Maintenance service parts and replacement parts:
We hold parts for the product for seven years after the discontinuation of
the product. Note: the maintenance service parts refer to the parts that
are required for repairing or restoring the product’s physical integrity or
functions to the intended optimum condition.
Disposing of the product:
When the product or the replaced parts are to be disposed of, treat them
appropriately according to the laws and regulations pertaining to proper
disposal in your country.
Upholstery Care
The following guidance applies to both synthetic and
natural leather upholsteries.
Adherence of fabric dyes:
The upholstery may be stained by coming into contact with fabric, belts or
other such attire. In order to avoid infiltration by plasticiser when colour
has been adhered, apply a solution of neutral detergent diluted by about
10% to a soft towel and wipe off the colour as soon as possible. After
wiping off the colour, wipe the area dry.
Colour deterioration and staining caused by contact:
• Contact with things such as other plastic parts, paints, solvents,
and adhesive tape may cause changes to the surface shine, cracking,
deformation, or peeling.
• Contact with newspaper or printed materials may cause colour staining.
• Contact with liquids such as benzene, nail polish remover, or alcohol
may cause the surface to discolour, dissolve, harden, soften, peel, extract
plasticiser, or experience changes to its shine.
• Using bleach or sheets that use bleach may cause discolouration or
changes to shine.
• Keep all sharp objects away from the upholstery.
• When placed next to a source of excessive heat such as an iron or
heater, deformation or discolouration may occur.
• Shield the upholstery with a curtain or other such item so that it does
not come into contact with direct sunlight. Otherwise, surface changes,
shrinkage, discolouration, or fading may occur.
• Heavy objects placed on the upholstery for long periods of time may
leave an impression and wrinkles that may be permanent.
Wrinkles and/or surface waviness may exist in the chair’s
upholstery or occur over time:
The product uses soft cushion materials and considered fabrics for
comfort and durability. Fabrics possess characteristic marks which exist
by design and not by fault. Furthermore, additional wrinkles and surface
waviness may develop depending on the demands and conditions of use.
CARE AND MAINTENANCE
Hydraulic Chair Manual for APOLLO 2_2016.6
© All Rights Reserved
Inspect Test method Defective results
Stability
of chair
and base >
Gently push or shake the
top of the backrest in all
directions, observing any
instability >
If you find the chair to
be unstable, do NOT use
it. Contact your dealer
or Takara Belmont for
advice.
Moving and
lockable parts
>
Use the foot pedal to
adjust the chair height,
checking that the chair
stops and locks at the
desired position without
sinking down >
If the chair does not stop
at the desired position, do
NOT use it. Contact your
dealer or Takara Belmont
for advice.
Function
without
obstruction >
Check that the chair does
not produce abnormal
sounds during rotation
and height-adjustment >
If the chair produces
abnormal sounds, do
NOT use it. Contact your
dealer or Takara Belmont
for advice.
Takara Belmont UK Ltd. Belmont House, 1 St. Andrews Way, Bow, London E3 3PA UNITED KINGDOM
takarahairdressing.co.uk T: [phone] E: [e-mail]